Question about 2013 Mercedes-Benz Sprinter

Open Question

Wing mirror arm replacement

I need to replace the arm on the exterior mirror

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 840 Answers

SOURCE: REPLACE SIGNAL BULB

You need a small flat screw driver and look at the back side the outer edge and push in and slowly pop out it has little dimples to keep it in. and if you need a mirror lens i hate to to tell you this you can try keystone automotive in the yellow pages it may be the cheaper but I would get one from Mercedes if need any more help go to collisionrepairadvice.com

Posted on Mar 10, 2009

Ad
  • 1986 Answers

SOURCE: How do i fit a replacement nearside wing mirror

You'll need a screw driver (philips is most common), a plastic prying lever, socket (should be 10mm, but can't remember)

If you're lucky, on the inside of the door, will be a triangular panel right behind the mirror that you can pop off. If you're not as lucky and it's one piece or the panel is blocked by the door panel, you'll need to remove the door panel to change it.

On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can remove the bolts holding the mirror onto the door

Posted on Oct 23, 2009

  • 7 Answers

SOURCE: mercedes w210 2001 wing mirror dissmantel to

Hi, Fold mirror in towards car and you will see an inspection hole at the bottom left of the end of the mirror housing. Insert a flat blade screwdriver into the hole and press against a small metal clip. you will feel the clip move and the housing will then slide off allowing you to unclip the glass

Posted on May 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have malfunctioning electric-driven exterior towing mirrors on a 1999 ford f-350. How to diagnose/fix? Mirrors respond only to right adjust; no response on up/down or left adjust.


there is a separate motor for up/down and another for left/right adjust. The glass is serviceable but not the motors, built into the frame of the mirror body.

SECTION 501-09: Rear View Mirrors 2000 F-Super Duty/Excursion/Motorhome Chassis Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass Removal
NOTE: Left-hand dual arm mirror with heat shown, non-heated and aero mirrors similar.
  1. Position the exterior rear view mirror glass in the full down position.
  1. Grasp the top and carefully pull the mirror glass away from the mirror housing.
  1. Disconnect the electrical terminals (if equipped) and remove the exterior rear view mirror glass.
Installation
  1. Remove the jack pins from the mirror glass back.
  1. Remove the sealing boots.
  1. Install the jack pins in the sealing boots.
  1. Install the jack pins and sealing boots.
    1. Install the jack pins in the mirror housing.
    1. Install the sealing boots so the boot shoulder is under the mirror collar.
  1. Loosely install the glass.
    1. Connect the electrical wiring to the electrical terminals (if equipped).
    1. Position the friction pins in the mirror housing.
    1. Align the jack pin locating tabs to match with the mirror glass back.
  1. Using a flat hand, press on the center of the mirror glass until seated on the center pivot of the mirror housing.
    • Press the mirror glass toward one of the jack pins until snapped in place.
    • Repeat for second jack pin.

Jan 13, 2011 | Ford F-350 Cars & Trucks

1 Answer

2002 Mountaineer. How do you change the light bulb at the bottom of the driver side rear view mirror. Dan


SECTION 501-09: Rear View Mirrors 2002 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Exterior Mirror Glass Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.

NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
ed6be7c.gif
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released.
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

Dec 26, 2009 | 2002 Mercury Mountaineer

1 Answer

How do I replace the passenger side exterior mirror?


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Aug 08, 2009 | 1996 Volvo 850

1 Answer

Whatis the procedure to replace the driver's side on 2005 Freesty


2005 Freestyle/Five Hundred/Montego Workshop Manual
  1. Remove the exterior mirror trim cover.(on inside of door)
  1. Disconnect the exterior mirror electrical connector.
  1. Remove the 3 exterior mirror nuts.
  1. Remove the exterior mirror.
  1. To install, reverse the removal procedure.

Jul 23, 2009 | 2005 Ford Freestyle

1 Answer

Passenger side mirroe is broken from the neck...


is it just the glass that broke?

Exterior Mirror Glass Removal
  1. Position the inner edge or the exterior rear view mirror glass to its maximum travel.
  1. s1h~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Place a shop towel between the exterior rear view mirror glass and the hand to avoid personal injury in the instance of glass breakage.
    Grasp the outboard edge of the exterior rear view mirror glass and pull outward.
  1. Remove the exterior rear view mirror glass.
    • If equipped, disconnect the heated rear view mirror glass electrical connectors.
Installation
  1. If equipped, connect the heated rear view mirror glass electrical connectors.
  1. NOTE: An audible click will be heard during installation.
    Press firmly in the center of the exterior rear view mirror glass until it snaps onto the exterior rear view mirror motor.

Jul 01, 2009 | 2001 Ford Taurus

1 Answer

Mirror glass replacement on drivers side


i don't have aviator. here's explorer, should be the same.

You will see a small rectangle where the screwdriver goes in. You are pryingtowards glass. The retention is about a 3 inch rectangle that has a lip around it that snaps onto a rectangle on the mirror body.

SECTION 501-09: Rear View Mirrors 2002 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released. (and pull screwdriver towards glass)
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

Apr 18, 2009 | 2003 Lincoln Aviator

1 Answer

1998 safari van - removal of passenger internal door panel


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. then you just remove the bolts to the mirror

Mar 22, 2009 | 1998 GMC Safari

1 Answer

2006 ford focus driver side mirror (electric)


Not that hard on this model.Here is a pic of the mirror and the removal and installation proceedure.

http://i253.photobucket.com/albums/hh43/chuck943/N0025797.gif

  1. Remove the exterior mirror trim cover.
    1. Release the retaining clip.
    1. Disconnect the exterior mirror control switch electrical connector.
  1. Disconnect the exterior mirror electrical connector.
  1. Remove the exterior mirror bolt.
    • To install, tighten to 11 Nm (8 lb-ft).
  1. If equipped, remove the exterior mirror screw.
    • To install, tighten to 2 Nm (18 lb-in).
  1. Remove the exterior mirror.
  1. To install, reverse the removal procedure.

Mar 02, 2009 | 2001 Ford Focus

1 Answer

Replacement of Mirror/Assembly, 2004 Ford E350 Super Duty


Exterior Mirror Removal and Installation
NOTE: Aero mirror shown, dual arm similar.
Manual mirrors
  1. Remove the mirror sail cover to gain access to the exterior mirror retaining nuts.
Power exterior mirrors
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. If equipped, remove the front door speaker.
  1. Remove the front door watershield.
All exterior mirrors
  1. Remove the rubber plugs and dust shield.
Power exterior mirrors
  1. Disconnect the electrical connector(s).
    1. Disconnect the power exterior mirror electrical connector.
    1. If equipped, disconnect the heated exterior mirror connector.
All exterior mirrors
  1. Remove the nuts and remove the exterior mirror.


  1. To install, reverse the removal procedure.
  2. 01cb1f9.gif

Jan 08, 2009 | 2007 Ford E-350 Super Duty Length XLT

2 Answers

How to remove mirror glass 2008 ford f350


here's 2003, don't have 2008

Removal
NOTE: Left-hand dual arm mirror with heat shown, non-heated and aero mirrors similar.
All exterior mirrors
  1. Position the exterior mirror glass in the full down position.
  1. Grasp the top and carefully pull the exterior mirror glass away from the mirror housing.
8157e6e.gif
  1. Disconnect the electrical terminals (if equipped) and remove the exterior mirror glass.
Power exterior mirrors
  1. Remove the jack pins from the exterior mirror glass backing plate.
    • Use pliers to grasp the jack pins at the base to remove.
429f568.gif
Installation
Power exterior mirrors
  1. Remove the sealing boots from the exterior mirror motor.
a8bd649.gif
  1. Install the jack pins in the sealing boots.
869a220.gif
  1. Install the jack pins and sealing boots.
    1. Hold the legs of the jack pins and push the jack pins back into the exterior mirror housing.
    1. Install the sealing boots so the boot shoulder is under the mirror collar and turn each jack pin until the head of the jack pin is aligned with the slots in the sockets on the backing glass plate.
95e6577.gif
All exterior mirrors
  1. Place the new exterior mirror glass assembly down on a smooth firm surface.
  1. Align the friction pins vertically to the exterior mirror glass backing plate socket and push down to snap the pivot ball into the socket.
52fef14.gif
  1. s3o~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not over heat the exterior mirror glass backing plate. Heat only until backing plate is warm to the touch.
    Using the special tool, warm the main pivot sockets in exterior mirror glass backing plate.
ed69017.gif
  1. Loosely install the glass.
    1. Connect the electrical wiring to the electrical terminals (if equipped).
    1. Position the friction pins in the mirror housing.
    1. Align the jack pin locating tabs to match with the mirror glass back.
  1. Using a flat hand, press on the center of the mirror glass until seated on the center pivot of the mirror housing.
    • Press the mirror glass toward one of the jack pins until snapped in place.
    • Repeat for second jack pin.
a10e39d.gif
Power exterior mirrors
NOTE: If the jack pins do not engage, they may not be aligned correctly. Remove the exterior mirror glass, align the jack pins to the slots in the sockets and repeat the installation procedure.
  1. NOTE: The jack pin should click while manually adjusting the exterior mirror glass.
    Tilt the exterior mirror glass to the full outboard position and then press on the outer side of the class until the in/out jack pin snaps into the socket on the exterior mirror backing plate.
  1. NOTE: The jack pin should click while manually adjusting the exterior mirror glass.
    Tilt the exterior mirror glass to the full down position and then press on the outer side of the class until the up/down jack pin snaps into the socket on the exterior mirror backing plate.

Nov 14, 2008 | 2008 Ford F-350

Not finding what you are looking for?
2013 Mercedes-Benz Sprinter Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

80637 Answers

Joseph Prosser

Level 3 Expert

772 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...