Question about 1988 Mazda B2600 Cab Plus

Open Question

1992 Mazda b2600 timing chain tensioner release

How to release tensioner

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

short shadey
  • 421 Answers

SOURCE: 1992 mazda B2600 ute

find the oil pressure sensor on the block and unplug it the light should go out, if not try grounding it if it goes out make sure you have adequate oil pressure and change the sensor please rate -jeff

Posted on Sep 01, 2008

  • 56 Answers

SOURCE: How to release tension to slip new belt on 2003

There should be a belt tensioner which requires a socket and a ratchet to pull tension off the belt by prying on this tensioner in the opposite direction.. Good Luck

Posted on Dec 08, 2009

  • 365 Answers

SOURCE: i need to set up the camshaft timing marks on a 1994 mazda b2600

its not just the camshaft timing marks you set up, you also have to have the crankshaft timing mark set right to or you may damage your engine
check the internet for the right timing procedure for you model car ok

Posted on Jun 11, 2010

MNfisherman
  • 11896 Answers

SOURCE: can a timing chain on 1992 Mazda 2600i jump a

Yes it can. The have plastic chain guides under the cover that can wear and cause slack in the chain which can cause it to jump. Have you used a timing light on it?
New plugs and wires?
Good fuel filter?
Check engine light off?

Have you tested power from coil packs or distributor?

A camshaft position sensor can cause this as well but most likely the check/service engine light would be on if there was a bad sensor.

Posted on Jul 23, 2010

Testimonial: "fast excellent reply!"

  • 6 Answers

SOURCE: how do i remove timing cover off 89 mazda b2600

put a rope to the car and toll it to the nearest scarp yard and burn the mazda

Posted on Nov 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Are mazda B2600 gearbox same to Mitsobishi. Can I replace Mitsobishi gearbox on Mazda B2600..1992?


Mazda and Ford parts will change,your B2600 with swap out with a 92 Ford Ranger.

Dec 25, 2012 | 1992 Mazda B-Series

1 Answer

How do i remove timing cover off 89 mazda b2600 2.6 seems to be hangin up at the bottom drivers side


put a rope to the car and toll it to the nearest scarp yard and burn the mazda

Nov 09, 2010 | 1988 Mazda B2600 Cab Plus

1 Answer

I need to set up the camshaft timing marks on a 1994 mazda b2600


its not just the camshaft timing marks you set up, you also have to have the crankshaft timing mark set right to or you may damage your engine
check the internet for the right timing procedure for you model car ok

Jun 11, 2010 | 1988 Mazda B2600 Cab Plus

1 Answer

How do you time a 2.6 mazda?


Here's a guide and diagram for you: (copy & paste entire link)
http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?partName=Timing+Chain+and+Tensioner&pageId=0900c15280076a5a&partId=0900c15280076a5a

Nov 28, 2009 | 1988 Mazda B2600 Cab Plus

1 Answer

How do you release the tension on the timing chains for the camshafts. i'm changing the head gaskets and can't figure out the timing chains tensioner. please help.


there are two large bolts in timing casing area 32mm size, one tensions cam chain the other tensions intermediate shaft chain, make sure engine is pinned in crank pulley to lock engine before releasing tensioners

Nov 04, 2009 | 2001 Porsche Boxster

1 Answer

96 brazo oil and mtal in over head cam engin stopped on highway


i have seen some mazda motors having busted cam shafts, so that's the only thing i can think of. if you didn't say behind the throtle body, i would say you have a busted piston but i doubt that's the case here.

Mar 02, 2009 | 1988 Mazda B2600 Cab Plus

1 Answer

1992 mazda B2600 ute


find the oil pressure sensor on the block and unplug it the light should go out, if not try grounding it if it goes out make sure you have adequate oil pressure and change the sensor please rate -jeff

Sep 01, 2008 | 1988 Mazda B2600 Cab Plus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...