Question about 2006 Chrysler Sebring

2 Answers

Why it is not starting?

Well my car keeps blowing out the A20 fuse and it wont start,everytime I turn on my car it blows out the fuse and don't start

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Did it blow the fuse b4 replacing the battery ...if not then you may want to recheck your connections on the battery if you have not yet.

Posted on Apr 21, 2014

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

When my car was blowing this fuse the starter needed replacing.

Posted on Apr 20, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What can i do to start my car?


u need to check that the battery was installed correctly. red cable to positive and black cable to negative post. did u get the same size battery as the old one?

Apr 20, 2014 | 2006 Chrysler Sebring 2.7

1 Answer

Odometer fuse keeps blowing when starting


Try a slow blow fuse? I think thats what they are called.

Mar 14, 2014 | 1996 Chevrolet Blazer

1 Answer

Cause fuse keep blowing


You have a short. you will need patience to route the wires from the harness to the light source, and to inspect for frail damaged wires.

Aug 16, 2013 | 2006 Toyota Sienna LE

1 Answer

Starter fuse keeps blowing


hi,i would say the solenoid on your starter is faulty

Mar 20, 2013 | 2000 Ford Crown Victoria

1 Answer

Amp fuse keeps blowing when car is turned off


It sounds like that fuse is supplying power to more than just the amp and is being shorted out in the START mode. Normally I would think the power to the sound system would be cut off by the ignition switch in the START mode. Try to find out what else that fuse supplies power to. You can disconnect suspected trouble areas to see if that helps locate the source of the fault.

Feb 16, 2013 | GMC Cars & Trucks

1 Answer

I have a 2003 mitsubishi lancer. Everytime I try to turn my key from the ignition to start my car my fuse 4 (40A) blows up I replaced it twice but the new fuse just keeps blowing up:/ what's going on?...


There is a major electrical fault that keeps blowing the fuse. The fuse protects that part of the electrical circuit, 40 amps is heavy electrical circuit, it it wasn't protected by a fuse it car could catch on fire.
You need to get an auto electrician or your Mitsubishi service center to locate the fault and repair.
If you had a wiring diagram for your car then you can trace the wiring from the 40A fuse to the various components to locate the wiring fault or component fault.

Dec 30, 2012 | Cars & Trucks

1 Answer

Ignition Fuse keeps blowing


Hi Jeff , in what fuse box is this 10 amp ign. fuse located ? I am looking at a power distribution diagram and i see a IGN 3 10amp fuse located in the I/P fuse box ! Is this the fuse that blows ? I see where you replaced the 10 amp with a 30amp . That is never a good idea , you don't want to make your problems worst . Melt wiring harness , could start a fire . Do you know how to do electrical trouble shooting ? How to use a wiring diagram , power distribuition diagram ? That fuse is hot in the run , powers the rear Heat / A/C , automatic level relay, ESC - electronic suspension control module , rear wheel steering control module , Plus someother thing's depending which vehicle , Y91 - ULT . Your Taho doesn't have all this options . http://www.bbbind.com/free_tsb.html find the thing's that fuse powers , disconnect them one at a time till the problem goes away .

Apr 08, 2017 | Cars & Trucks

1 Answer

Mycar wont start ichanged the fuelpump fuse and it keeps blowing its a 2003 pontiac grandam it turns over just wont start


REMOVE FUEL PUMP RELAY.REPLACE FUSE IF STILL BLOWS SHORT IN PCM TO IGNITION CIRCUIT.IF FUSE DONT BLOW I AM LOOKING AT A BAD FUEL PUMP RELAY OR FAULTY FUEL PUMP.

Jul 10, 2010 | 2003 Pontiac Grand Am

2 Answers

Fuel ECU fuse keeps blowing (30 amp)


Your fuel pump is internally binding and causing the fuse to blow. Change the pump (and filter while you're back there.)

Jun 14, 2009 | 1993 Jeep Wrangler

Not finding what you are looking for?
2006 Chrysler Sebring Logo

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...