Question about Cars & Trucks

1 Answer

Were is camshaft position sensor 97 silverado

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

I am sure it is above the starter motor at the bottom left side of the vehicle block looking at the vehicle from the front.

Posted on Apr 20, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
davesmith_37
  • 94 Answers

SOURCE: P0340 Code Camshaft Position Sensor


The Camshaft Position (CMP) Sensor detects the position of the camshaft in order to identifiy when piston No. 1 is on its compression stroke. The CMP sensor is used for ignition timing in the Ford DIS igntion system, but not in the EDIS igntion system. Both DIS/EDIS use the CMP signal for synchronizing the firing of sequential fuel injectors.

On the 3.0L vulcan engine, the CMP signal is generated by a single Hall-Effect magnetic switch, activated by a single "vane" spinning around by virture of a synchronized shaft which is driven by the camshaft. 

The CMP sensor & synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Posted on Feb 27, 2009

  • 218 Answers

SOURCE: Camshaft Position Sensor Location

IF U GO TO THE RIGHT SIDE OF THE ENGINE AND LOOK 4 INCHES BEHIND THE BELT IT WILL BE ON TOP OF THE TIMING COVER.THE WIRES WILL BE RED/WHITE,BLACK,BROWN/WHITE

Posted on May 05, 2009

  • 1 Answer

SOURCE: camshaft position sensor

The camshaft position sensor is on the rear cylinder head on the left end (the serpentine belt end of the engine - passenger side). It is a son-of-a gun to get at. When it is bad or the connector is intermittant or bad, the symptom will be irregular idle from 500 to 750 RPM or so.

Posted on Aug 22, 2009

  • 144 Answers

SOURCE: Where is the camshaft position sensor located in a 2001 VW Passat

when you are looking at the engine pull off the plastic cover on top then the front cover that covers you timing belt there is a wire harness tha goes right to it in the left upper coner two ten mil bolts and it comes off careful not to drop bolts down in belt that could be bad. it is that easy

Posted on Sep 01, 2009

alicantecoli
  • 22156 Answers

SOURCE: 2000 Daewoo Nubira camshaft position sensor

on the front under timing belt cover ,back cam ,if its not their then back of head about 3inches along from the gear wheel end

Posted on Sep 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the cam position sensor on a 97 Hyundai elantra


Hi Zolo,here's a link to your camshaft position sensor. Duralast Camshaft Position Sensor SU4117 ReadReviews onDuralast SU4117 The Camshaft Position Sensoris located: Under hood, passenger side, upper engine area, mounted in engine block .Here's another on how to replace it.
Repair Guides Electronic Engine Controls Camshaft Position cmp Sensor...

Sep 28, 2016 | Hyundai Cars & Trucks

1 Answer

I have 97 silverado. 5.0 vortex with code p1345 changed crank position sensor camshaft position and done a tune up. Why would this code still be on and still have a bad misfire


This code usually sets if a distributor has been istalled incorretly (a tooth or so off)..
Have you had the distributor removed recently or before the code started showing up?

Also, once the problem is fixed the computer will have to monitor it for a while before it turns off the check engine light.(or you can get someone with a scan tool to turn it off for you.

Jul 29, 2014 | Cars & Trucks

1 Answer

Where are the camshaft and crankshaft position sensors on 2001 silverado 8.1 V8


pic-1681384701591865649-tmb.jpegCrank shaft sensor
Remove the driver side rear ignition coil bolts. Reposition the coil. Disconnect the crankshaft position (CKP) sensor electrical connector. # Use penetrating oil and allow the oil to soak around the CKP sensor prior to removing the sensor. You're looking at left, rear side of engine.
CAMSHAFT POS.
front side of engine on the drives side about half way up the timing cover, not hard to get to.

Nov 11, 2013 | Chevrolet 3500 Cars & Trucks

1 Answer

Will my car a (97 nissan maxima)run hot wen the camshaft position sensor or maf sensor is bad


No that would not affect temperature in any significant way. the engine in most cases just won't run or will be hard starting.

Jun 21, 2012 | 1997 Nissan Maxima

2 Answers

P1345


With your code reader, clear the codes and check they stay gone.

Aug 15, 2017 | Cars & Trucks

2 Answers

98 silverado 5.7L camshaft position sensor


ITS ABOVE CRANKSHAFT PULLEY.IT CONNECTS WITH CRANKSHAFT POSITION SENSOR.

Oct 23, 2009 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Camshaft positioning sensor


Maybe your oxygen sensor is not working

Jul 28, 2009 | 1997 Chevrolet Cavalier

1 Answer

2004 Chevy Silverado HD 2500


On many engines with distributor less ignition systems and sequential fuel injection, a camshaft position sensor is used to keep the engine's control module informed about the relative position of the crankshaft. By monitoring cam position (which allows the control module to determine when the intake and exhaust valves are opening and closing), the control module can use the cam position sensor's input along with that from the crankshaft position sensor to determine which cylinder in the engine's firing sequence is approaching top dead center. This information is then used by the engine control module to synchronize the pulsing of sequential fuel injectors so they match the firing order of the engine. On some applications, input from the camshaft position sensor is also required for ignition timing.
The camshaft position sensor may be magnetic or Hall effect, and mounted on the timing cover over the camshaft gear, on the end of the cylinder head in an overhead cam application, or in a special housing that replaces the distributor (in the case of some of the GM applications). Operation and diagnosis is essentially the same as that for a crankshaft position sensor.  

Re  check the wire harness and the sensor installation to the camshaft sensor in Bank #1 which is where the #1 cylinder is. Good luck and hope this adds some light to you question, keep me posted and be glad to help.

Jun 02, 2009 | 2003 Chevrolet Silverado 2500HD

1 Answer

Where is the camshaft and crankshaft position sensors on a 1998 Silverado with a 5.0 Liter 305 V8?


The camshaft position sensor is the distributor on the back top of engine. The crankshaft position sensor is right behind the harmonic balancer on the front of the engine

Jul 29, 2008 | Chevrolet C1500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...