Question about Cars & Trucks

1 Answer

1997 Chevy z71 were is camshaft position sensor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Cars & Trucks Master
  • 808 Answers

Is located in the distributor.

Posted on Apr 21, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
leetamara
  • 702 Answers

SOURCE: where is my camshaft positioning sensor located

The CMP (camshaft position sensor) is located where the distributor would normally be.

Posted on Jul 02, 2008

  • 39 Answers

SOURCE: Where is the camshaft position sensor located-99 Chevy Lumina 3.1

It's held down by one bolt right above the timing chain cover. It's next to the head that's facing toward the front of the car.

Posted on Feb 06, 2009

  • 1 Answer

SOURCE: camshaft position sensor

The camshaft position sensor is on the rear cylinder head on the left end (the serpentine belt end of the engine - passenger side). It is a son-of-a gun to get at. When it is bad or the connector is intermittant or bad, the symptom will be irregular idle from 500 to 750 RPM or so.

Posted on Aug 22, 2009

  • 14036 Answers

SOURCE: 98 silverado 5.7L camshaft position sensor

ITS ABOVE CRANKSHAFT PULLEY.IT CONNECTS WITH CRANKSHAFT POSITION SENSOR.

Posted on Oct 23, 2009

  • 3640 Answers

SOURCE: Getting the following codes from a 1997 Pontiac Grand Am....... PO121 TPS / Pedal Position Sensor A CKT Range / Perf Also, PO341 Camshaft Position Sensor A - Bank 1 CKT Range/Perf. Any thoughts on the

po121 means that there is a problem with the throttle position sensor ( tps). or in the wiring or connector, most likely its the tps that is bad. first remove connection from tps, heres how to test. use an ohms meter and hook a lead to top or bottom terminal of tps. use other probe on center terminal of tps. move throttle plate slowly, if the needle on meter does not move at a smooth pace, then tps is bad. good-luck!!

Posted on Oct 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1997 Chevy 1500 Cheyenne with 305 vortex with code p1345 manufacturer control. Ignition system or misfire


does the engine run? If it does you may have a loose / intermittent connection at the crankshaft sensor or cam sensor. Check the crankshaft position sensor. Make sure it isn't loose. Also check the camshaft position sensor.

Mar 02, 2017 | Chevrolet Cars & Trucks

1 Answer

Picture of camshaft sensor 1997 Chevy Silverado 350 vortech


The cam shaft position sensor is in the distributor housing and is the only sensor in the unit.

Apr 20, 2014 | Cars & Trucks

1 Answer

1998 gmc z71 surges in drive p1345


The P1345 means SGC (Cam Position) sensor circuit malfunction/crankshaft position-camshaft position correlation
P0300 means random/multiple cylinder misfire detected

mpps ecu chips

Aug 07, 2012 | 1998 GMC Sierra

1 Answer

How to fix p1345 obd code on 97 chevy 1500 5.7 Lt.


P1345 is "Crankshaft position sensor / Camshaft position sensor correlation"

Code P1345 determines if the distributor is installed incorrectly, or if a mechanical malfunction is present in the engine. The light will trigger when the engine is running and the camshaft sensor reference pulse is not detected at a correct relative position with the crankshaft pulse. Most likely causes for this Chevy check engine light code include a faulty crankshaft position sensor, a wiring concern or an improperly installed distributor. A quick check on the crankshaft sensor is to monitor the RPM value with a scan tool while revving up the engine. If the reading is close to twice the expected RPM, then the sensor is likely faulty. There are other less likely concerns possible, such as base engine or computer related issues, but these involve more in depth testing. I hope this information is useful.

May 27, 2011 | 1997 Chevrolet K1500

1 Answer

Where is the cam position sensor on a 1997 chevy 5.7L


The camshaft position sensor (also known as the distributor pickup) is inside the distributor which is driven by the camshaft gear and directly below the water pump, the water pump must be removed to access the distributor to change the sensor. Here is a picture of the camshaft position sensor.


emissionwiz_90.jpg

Jan 13, 2011 | 1997 Chevrolet K1500

1 Answer

How do you check and change a camshaft position


The camshaft sensor wouldn't explain the clattering noise. But a timing chain would explain both. Clattering from a loose chain and the camshaft sensor code from when the chain broke and the camshafts stopped turning.

Aug 02, 2010 | 2000 Chevrolet Tracker

1 Answer

How to install a 1992 chevy pickup camshaft sensor 1992 chevy pickup 1500 z71 and where is it located? i have no spark coming from my coil so this is my next task? any other answers?


There isn't a camshaft sensor. The distributor has a control module and a pick up coil inside of it, 1 or both could be bad, it's usually best to replace both. Some parts stores can test them. The is also an Electronic Spark Control Module. I would check the pick up coil and control module.

Apr 30, 2010 | 1992 Chevrolet K1500

2 Answers

1997 K1500 z71 4X4 Chevy (Throttle position sensor)


does anyone know where the throttle position sensor is located on a 1997 chevy Z71 truck ?

Jan 19, 2010 | 1997 Chevrolet K1500

1 Answer

Camshaft positioning sensor


Maybe your oxygen sensor is not working

Jul 28, 2009 | 1997 Chevrolet Cavalier

1 Answer

1997 mercury sable camshaft sensor replacement


do you have 3.L 2v or 4 valve?

3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder blocks (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (12270) (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder blocks.
Installation
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be used to position the synchronizer assembly prior to installation of the camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs. Locate camshaft position sensor electrical connector in the pre-removal position.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (14-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.

Feb 22, 2009 | 1997 Mercury Sable

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...