Question about 2007 GMC Envoy Denali

1 Answer

Ujoint what should the cost be to replace a ujoint

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 9,587 Answers

Depends on where it is located. If its on the drive shaft for the rear wheels the cost will be lower than the ones on the front wheels. Shop around. Drive line shops specialize in them but any good mechanic can do it.

Posted on Jul 24, 2016

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just replaced rear joint on my 1997 Chevy 1500 4x4 (5.7L). Went down the road and the caps on the joint that are tightened by the four bolts popped out. I did put in the clamp rings but they still popped...


There should be clips in the grooves on the caps that are held in by the drive shaft straps.All ujoint caps either have a clip in a groove or a snap ring clip on top that fits into a groove on the drive shaft yoke.These clips not only help keep the ujoint front spitting the caps out they also center the ujoint in the yoke on the rear axle.If you dont have a clip groove then you may have the wrong ujoint.Look closely at the old ujoint and you should see what I mean.Good Luck!

Mar 27, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Theres play in my front drive shaft. I dont know if its the u joint or the rear end going into the transfer case. what is the most in expensive way to fix problem. problem is when braking accasionally feel...


the cheapest way would be to remove the front driveshaft I guess... This will give you opportunity to inspect the Ujoints too!
If it is only a Ujoint... you can replace the Ujoint and shaft when you have the money to do so...

Sep 28, 2010 | 1992 Ford Explorer

4 Answers

Need a source to get a replacement part Ford F150 20004 Truck


a rear u joint shouldnt cost more than about 30 bucks at any autoparts store...napa, canadian tire, pep boys whatever.

Sep 03, 2009 | 2004 Ford F150

2 Answers

How to replace front u joints 2001 suburban?


if its 4wd drop front drive shaft remove the clips that hold the ujoints in place use a socket or a punch about the size of ujoint cap put in vise and knock out the old joint and replace with new one careful not to hurt needle bearings in the caps. if it is rear wheel drive and two piece driveshaft undo the the shaft at rearend and undo the center support bearing in the middle of the two shafts and pull out of vehicle replace ujoints same way as above. if it does not have the clips holding caps it plastic seal which needs to be heated up until the plastinc runs out of hole in flange

Aug 30, 2009 | 2001 Chevrolet Suburban

1 Answer

How do you change the front universal joints on a 2003 dodge ram 2500 4x4


The drive shaft will need to be removed. Remove ujoint cap clips from yolk and shaft. Should be four all together.tap out the u joints.
Remove cap from new ujoint. place into yoke from outside. Slip ujoint inside, attach to cap. press ujoint into housing. do the same with drive shaft side. Dont forget to put the new clips provided, on the shaft and yolk

Jul 23, 2009 | Dodge Ram Pickup 2500 Cars & Trucks

1 Answer

I need a ujoint, do they just replace it or the whole axle?


u-joints are replaceable. Or, get a used driveshaft at car-part.com. page with asterisk is low price.

May 22, 2009 | 2005 Nissan Xterra

1 Answer

What is the flat rate time & materials to r&r front ujoint


you will need u-joints,frt hub seals,axle shaft dust seals and hub o-rings.most ford dealers charge 3 hrs for the hub service(seals) and 1.5 hrs to replace L+R u-joints.if they try to charge any more than 4.5 hrs go to different shop.if DIY there is a special seal driver needed to complete this repair.

Oct 20, 2008 | 2000 Ford F250 Super Duty Crew Cabs

Not finding what you are looking for?
2007 GMC Envoy Denali Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...