Question about 1998 Plymouth Grand Voyager

1 Answer

What is the torque specs for the transmission oilpan on a 98 plymouth grand voyager/

Posted by on

  • rnys865 Jun 19, 2009

    Thank you very much. I just needed to know how tight and it would appear that it is just past hand tight but not cranked in.

  • Greg Margossian
    Greg Margossian May 11, 2010

    What is the engine size?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 6,982 Answers

You don't really need exact specs on that but it is usually around 14 inch pounds... Just use a nut driver or 1/4 in drive ratchet and use a cross pattern on the bolts, not a circle. do not tighten anything 'till you have every bolt in and verify that it goes in easily. Be careful to not crush the gasket, after you get the fluid in, watch for seepage and tighten up wherever you see any . Most important to remove all old gasket material from both pan and trans rail that is the primary cause of leaks.

Posted on Jun 19, 2009

  • Richard Scordino Jun 19, 2009

    You've got it! it's too easy to pull the threads out of an aluminum case!!! Also easy to cross-thread. Good luck!

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front turn signal light bulb on 1993 Plymouth Grand Voyager SE 3.0 L


Need a screwdriver etc..lift hood and u see attachments or it may b in front..dontrush

Mar 24, 2018 | 1993 Plymouth Grand Voyager

1 Answer

How do i change out a torque converter for a 2000 plymouth grand voyager se??


Drop the transmission and replace convertor and then reinstall. Not a DIYS job, you really need a lift

Jan 04, 2015 | 2000 Plymouth Grand Voyager

1 Answer

1998 plymouth voyager , transmission will not shift past second gear,


Buy an ATSG Transaxle Manual

They are avail on their web site or at
a local trans supply house where the local
shops go for parts

Mar 31, 2014 | 1998 Plymouth Grand Voyager

1 Answer

Transmission diagram


the tcm is the computer to the transmission and it is that silver looking box on inner passenger fender under the hood.

May 02, 2013 | 1998 Plymouth Grand Voyager

1 Answer

Where is the tcm located on a 98 plymouth grand voyager


The TCM transmission control module is on top of the front right wheel well, right in front of the powersteering reservour. You did not state what your problem was. There has been a some problems with wires and terminals opening up and losing contact. Take an ohm meter and check your connections before blaming the TCM. I have a problems with an open wire on my 98 grand voyager. I found the wire that is the problem but now can;t find a terminal so I can splice in a wire and put a terminal on it. I'm hitting the salvage yards tomorrow to try and get part or a whole harness to fix it.

Oct 23, 2012 | 1998 Plymouth Grand Voyager

1 Answer

Need torque specs to replace head gasket on a 1989 plymouth voyager


Normaly supplied with the head gasket with the sequence in which to tighten them.

Jun 24, 2012 | Plymouth Voyager Cars & Trucks

1 Answer

Torque specs for main and rod bearing 98 plymouth voyager


I'd suggest you go to www.autozone.com and register for free. Once registered you'll have access to many manuals, including shop manuals, that will provide the info you need now and should be beneficial to you whenever you have a problem.

Mar 27, 2011 | 1998 Plymouth Voyager

1 Answer

Torque specs for 98 Plymouth voyager 3.0 intake manifold


ramundoo_3.giftorque spec is 20 -28 ft pound.here is the sequence.thankyou.ramundoo

Mar 16, 2011 | 1998 Plymouth Voyager

1 Answer

I have a 98 plymouth voyager, the back up lights do not work


replace the transmission park and neutral switch.most of the time when it stop working your back up lights stop working.

Jul 20, 2009 | 1997 Plymouth Grand Voyager

1 Answer

Engine swap from 2.4 to 3.0


yes it will but u will need to swap all the engine related electronics as well.

Jun 01, 2009 | 1998 Plymouth Grand Voyager

Not finding what you are looking for?
1998 Plymouth Grand Voyager Logo

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...