Question about 2006 Mercury Mariner

Open Question

Iac 2006 mercury mariner iac location - 2006 Mercury Mariner

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 28 Answers

SOURCE: 2006 mercury mariner. stupid tail light assembly.

they are hard to take off sometimes, you are doing it right just keep willing it it will come off, there is 2 gromits that hold it into place might have a little dirt into the plunger.

Posted on Feb 22, 2009

  • 1 Answer

SOURCE: 2006 Mercury Mariner - sticky gas pedal

I have a 2005 Mariner with the same problem. Always when the weather drops

Posted on Jan 09, 2010

johnjohn2
  • 5763 Answers

SOURCE: How do I reset the oil change light on a 2006

there are two types of displays heres both.hope this helps.for base instrument cluster.
1) press and release trip/reset button until setup menu hold reset displayed
2)press & hold trip/reset untilreset for sys check or sys check hold reset is displayed
3)release trip/reset button
4)press and release trip to scroll until hold reset if new oil is displayed
5)press and hold resetuntil oil life set to 100% and let button go you are done.
if you have a message center dash display then do this one. 1)push and release setup button until you see press reset to begin (2)press& release reset button until hold resetif new oil is displayed.(3)press and hold reset for 2secondsuntiloil set to 100%. done. hope this helps.

Posted on Jan 27, 2010

Ford007
  • 131 Answers

SOURCE: how to I change the right tailight on my 2006

Open the liftgate and remove the 2 screws holding the lamp. Now grab the lamp and pull straight back to dislodge the spring clips. Then twist the sockets to remove the bulbs.

Posted on Mar 17, 2010

  • 1 Answer

SOURCE: Need to find the computer module on the 2006 Mercury Mariner

Located on passenger side. Tou need to look under the dash then turn to look under the console. You will see a black box PAT unit around 8 or 10 inches long with fairly large numbers printed on its side. These are the 5 numbers you will need

Posted on Jun 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the 2006 mercury mariner reverse switch located?


Assuming a V6 and A/T, the reverse lamps relay is located in the smart junction box.

Oct 14, 2016 | 2006 Mercury Mariner

1 Answer

What fuse location does the Auxiliary Power Point use on a 206 Mercury Mariner?


Assuming your Mariner has a V6 and is not a hybrid, 20A FUSE 12 in the battery junction box (BJB) supplies 12 volts to the power point.

Sep 21, 2014 | 2006 Mercury Mariner

2 Answers

2006 Mercury Mariner - sticky gas pedal


I have a 2005 Mariner with the same problem. Always when the weather drops

Jan 07, 2010 | 2006 Mercury Mariner

1 Answer

2006 Mercury Mariner V6 4WD. Sporadic stalling when stopping


One of the most common causes of stalling like that but not showing any fault codes on many types of vehicles is the IAC valve, or IAC motor. (same thing) It's mounted on the side of the throttle body near front opening and it controls engine idle under load conditions such as applying brakes, turning wheel, AC on, basically anything you use in vehicle that puts any load on the engine, which will make RPM's drop at idle, that valve, steps it up to where it should be to eliminate that. I'd remove it, get a can of throttle body spray cleaner, and clean pintle (pointed part) and the port (hole) it came out of real good, then re-install it & see if problem goes away. If it goes away, then returns before too long, replace it with a new one.

Aug 06, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Need to find the computer module on the 2006 Mercury Mariner


Located on passenger side. Tou need to look under the dash then turn to look under the console. You will see a black box PAT unit around 8 or 10 inches long with fairly large numbers printed on its side. These are the 5 numbers you will need

Jun 07, 2009 | 2006 Mercury Mariner

1 Answer

2006 mercury mariner. stupid tail light assembly.


they are hard to take off sometimes, you are doing it right just keep willing it it will come off, there is 2 gromits that hold it into place might have a little dirt into the plunger.

Feb 22, 2009 | 2006 Mercury Mariner

1 Answer

Removing tail light assm


From Inside The Trunk Or Hatch Whichever You Prefer. Locate The Panel Or Carpeting. It Will Be Directly Behind Where The Light Is Located Only On The Inside. Remove That Panel And Or Carpet And Youll Find Three Bolts Holding The Unit In Place.

Jan 23, 2009 | 2006 Mercury Mariner

Not finding what you are looking for?
2006 Mercury Mariner Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...