Question about 1987 Chevrolet Monte Carlo

1 Answer

Bumper diagram front

HEADLIGHTS WONT BOLT ON, MISSING A BRACKET

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Are you serious? What other possible solution are you looking for this is a monte carlo you either go find the bracket or you put on your redneck gear and grab some bondo (not suggested....)

Posted on Jun 21, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002chevy silverado no low or high lights.changed switch,bulbs,fuses and relays good.have power to light socket.what else can it be


Have you had any recent body damage out front ? The grounds for the headlights are bolted to the radiator support "ears" on the frame just behind the bumper. make sure nothing has damaged them. You will see a 10mm bolt and about a 12ga black wire .If these grounds aren't made, you wont have lights..
Let me know if this doesn't fix it and I will study the wiring diagram ..

Jan 04, 2017 | Cars & Trucks

2 Answers

2005 350z headlight upgrade to 08 xenon headlights


Do you know if the 08 bumper even fits?
Thanks,
Lee

Jun 17, 2008 | 2005 Nissan 350Z

1 Answer

How do I go about installing a Warn winch on the metal bumper and chassis of a 1996 3.0l v6 Mitsubishi Pajero without modifications? Cables are standard Warn designed for this winch.


just make sure you get the right steel plate for your bumper to hold the winch on or it will rip your bumper off the first time you use it make sure it is bolted sucure

Jan 19, 2015 | Mitsubishi Cars & Trucks

1 Answer

How to take off existing fog lights on a 2003 escalade and install new fog light assembly


The fog lamp assemblies can be removed by getting underneath the front bumper and on top of the fog lamp assemblies you will find the metal mounting bracket. The bracket attaches to the vehicle with 3 small bolts that are 8-10mm (i forgot exactly) that bolt down through the bracket into the front bumper cover above the actual lens itself and can be accessed with a box wrench. I replaced both assemblies in mine in under 1/2 and hour!

Jun 24, 2010 | Cars & Trucks

1 Answer

How do i replace the headlights


Front bumper requires removal to gain acsess to the lower 10mm bolts. Bumper comes off by removing the 2 10mm bolts on the top of the bumper then unscrew the 2 T30 screws in the front wheel arch liner (bumper side) and then you will be able to see a 10mm bolt reversed into a bracket at the top of the bumper from a inside veiw, remove and repeat for the other side. Then its 3 10mm bolts that secure the front under tray (if yours has one). Then there will be another 10mm bolt to the wing side of the headlamp from a above veiw. Bumper should then just pull off and watch for the connector for the fog lamp harness.

Just the 2 lower headlamp bolts andit should pull from its housing

Mar 29, 2010 | 2003 Jaguar S-Type

1 Answer

Tow bar (mounts) front end of larado


Use the same bolt holes the front bumber uses. You may have to build a bracket that attaches to the frame horns where the bumper mounts and using longer bolts (grade 8) pinch the bumper between the mount and the frame horns. Attach your tow tongue to this mount.

Jan 15, 2010 | 1994 Jeep Grand Cherokee

1 Answer

I neede to remove the headlights for my 2008 E 350 and need instructions. OIt appears that removing the front bumper is needed ? Thanks


Here's some instructions for removing bumper and headlights.

E-Class W211 front bumper removal (standard body style).

Tools needed:
- Automotive wheel ramps (Rhino ramps from Autozone).
- 1/4" drive socket set with 8mm and 10mm sockets.
- #20 torx bit.
- Floor jack, optional but useful.
- Flat blade screwdriver.

Instructions for bumper removal:

1) Turn front wheels full right to remove push-pin fastener at lower front corner of left wheel well plastic splash guard. It's difficult to remove this fastener once the car is up on the wheel ramps.

2) Turn front wheels full left to remove push-pin fastener at lower front corner of right wheel well plastic splash guard.

3) Drive car up on wheel ramps. Block rear tires. Open hood.

4) Remove lower mesh plastic grille. There are five attachment points on the top edge of the grille. You can get to three of them with your hand by reaching between the radiator and the back side of the grille. The two outer ones can be released with a screwdriver also reaching in between the grille and radiator. Once the plastic tabs are released, you can remove the grille by pulling it out from the front of the car.

5) Remove the plastic panel located immediately behind the bumper from the bottom of the engine compartment. This panel is held in place with nine sheet metal screws with a 8mm hex head. Five screws are on the bottom of the car and there are two screws in each wheel well at the inner lower edge. After removing all nine screws you can work the panel free.

6) Disconnect the cable from each fog light and remove both fog lights. They are held in place by two sheet metal screws with a #20 torx head.

7) Remove the side marker bulbs. The one on the passenger side turns clockwise to remove and the one on the driver side turns counter-clockwise.

8) Remove the temperature sensor from its socket on the driver side.

9) If you have a floor jack, raise the car at the jack point on the cross member below the engine. You do not want to raise it off the wheel ramps. But it helps to have more clearance above the tires to work in the front wheel wells.

10) Remove three of the plastic nuts holding the forward half of the plastic wheel well liner in place. It's not necessary to remove the plastic liner. You just need to loosen it up so that you can pull it away from the fender to gain access to the screw and bracket securing the bumper to the fender.

11) Pull back the wheel well liner and remove the sheet metal screw from the rear end of the metal bracket . There is only one sheet metal screw (#20 torx head) holding this bracket in place. Don't attempt to remove the bracket yet. I used a #20 torx bit in a 1/4" socket with a 6-inch extension for a 1/4" drive wrench. The head of the screw faces the ground.

12) Remove the 5mm bolts (8mm hex head) holding the bumper to the headlight assembly between the small lens and large lens (both sides).

13) Remove the two 6mm bolts (10mm hex head) on either side of the large grille area opening.

14) Remove the two 6mm bolts (10mm hex head) securing the bumper to the bottom edge of the crashbar. You can access these bolts through the front where you removed the plastic mesh grille.

15) Remove the three 5mm bolts (8mm hex head) holding each headlight assembly in place. Two longer bolts are on top. One at the rear outer corner and one at the front inner corner. The third bolt is accessed from the bottom. It's in the area above the fog lamps. You don't need to disconnect the headlight cables and remove the assembly. But it helps to allow the headlight assembly to "float" freely while you disengage the bumper from the fender.

16) At this point all of the fasteners holding the bumper in place have been removed. The only thing left to do is to remove the two brackets "clamping" the bumper cover to the lower front edge of the front fenders. Before you do this, position some cardboard boxes, bags of packing material, six packs of paper towels, or other suitable items to protect the bumper in case it falls off the car.

17) The bracket holding the bumper cover to the fender has a "pin" that slips into a slot at the front edge of the bumper cover. There is a matching slot near the front edge of the fender. It's not possible to see this pin from the bottom of the car. Use a flat blade screwdriver to pry the bracket away from the bumper/fender and towards the center of the car. The bracket will "hinge" on the pin at the front end of the bracket. After you swing the bracket away from the bumper, you need to slide it forward to remove it from the slot in the bumper cover and fender. You will probably scratch some paint off of this bracket with the screwdriver. I recommend repainting the scratched areas of the bracket before reinstalling it.

18) After removing the bracket from each side of the car you need to deal with the small plastic "hook" holding the bumper cover to the very front tip of the fender. This hook is an integral part of the bumper cover. Disengaging this hook from the fender is probably the most difficult step of removing the bumper. Simultaneously raise the head light assembly slightly, push the leading edge of the fender outward slightly, and push the bumper cover inward toward the headlight assembly. Don't get too aggressive with the fender. It's aluminum and you will make a real mess if you apply too much pressure on the fender. It took me about 20 minutes to free each side from this hook. It should take you less time, since you now know that the hook exists!

19) Gently pull the bumper forward and away from the car. This is one step where a second person would be helpful. But I did manage to do this step alone. There is a "pulley" like attachment point on each side just below the fender/bumper seam.

To re-install the bumper, reverse the order of the steps above. When re-installing the bracket between the bumper cover and fender, I smeared a thin coating of car wash soap on the bracket to facilitate snapping the bracket back into place.




Oct 09, 2009 | Mercedes-Benz E350 Cars & Trucks

1 Answer

Instal diagram for nissan xterra grill gaurd


they jusy bolt to bomper brackets and where bumper bolts to bracket hey vote for me ok

May 26, 2009 | 2008 Nissan Xterra

1 Answer

How can I change the headlights in a 1998 Honda Accord?


Its not that hard but you have to remove bumper to get to the two bottom bolts that holds the headlights. First remove grille and there are 2 10mm bolts that holt the tip of fenders they are the first bolts under the fender weld closes to the bumper cover. Then there are two bumper mounts/brackets that hold bumper to frame/radiator support. they are held by (4) 12mm bolts may need a swivel socket to get to them( easily accessed if you remove front signal lights in the bumper held by philips screws in the corners).After removing bracket bumper should come right off. Headlights are in plain clear view. (4) 10mm bolts and you are done. Re-install in the reverse. Good Luck . If I fixed ya leave me a FIX-YA comment. Contact me if you need more info

Dec 10, 2008 | 1998 Honda Accord

Not finding what you are looking for?
1987 Chevrolet Monte Carlo Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...