Question about 2006 Aston Martin DB9

Open Question

To remove the lock from the door - 2006 Aston Martin DB9

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

Tip

How to Replace Door Locks in Cadillac cetera car?


The procedure to replace the door locks in car is as follows:--
1) First of all carefully remove the arm rest and any speaker covers if speakers are connected.
2) Then remove the door panel. The door panel is connected by plastic clips.
3) Then remove the door handle screws with the help of screwdriver.
4) After the screws are removed the door handle will come out
5) Now the interior doors handle needs to be removed. the interior door handle is fitted by plastic clips you can use a pliers to pop out the plastic clip, then twist the clip to allow the interior door handle to swing free and easily come out.
6) Take the door handle out
7) Now in the door remove the rod from lock core.Then remove the two bolts holding the door handle assembly.
8) Now before removing the old door lock, please take note of the position in which it is placed. So while inserting new lock there is no problem about placing the new lock.
9) Insert the new lock carefully to the proper position. And reverse/refit all the parts which you removed while replacing the old door lock.
This will help. Thanks.

on Mar 25, 2010 | Cadillac Catera Cars & Trucks

Tip

How to Replace Door Locks in Eagle Vision ?


The procedure to replace the door locks in car is as follows:--
1) First of all carefully remove the arm rest and any speaker covers if speakers are connected.
2) Then remove the door panel. The door panel is connected by plastic clips.
3) Then remove the door handle screws with the help of screwdriver.
4) After the screws are removed the door handle will come out
5) Now the interior doors handle needs to be removed. the interior door handle is fitted by plastic clips you can use a pliers to pop out the plastic clip, then twist the clip to allow the interior door handle to swing free and easily come out.
6) Take the door handle out
7) Now in the door remove the rod from lock core.Then remove the two bolts holding the door handle assembly.
8) Now before removing the old door lock, please take note of the position in which it is placed. So while inserting new lock there is no problem about placing the new lock.
9) Insert the new lock carefully to the proper position. And reverse/refit all the parts which you removed while replacing the old door lock.
This will help. Thanks.

on Mar 25, 2010 | Eagle Vision Cars & Trucks

1 Answer

How do i remove the driver's inside panel door? My electric button panel for windows and locks isn't moving.


Like reference guide, check this procedure to Removal & Installation / Door Lock Motor...

The door lock motor is integral with the door latch. If the door lock motor is found to be defective, the entire door latch must be replaced.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Roll the door glass down.
  3. Disengage the 2 clips attaching the speaker grille to the door trim panel. (They are at the front of the grille, one near the top, and the other one at the bottom).
  4. Remove the 3 large washer-headed screws surrounding the speaker.

    6acb803.jpg
    Fig. Fastener location for the door lower trim panel
  5. Remove the access cover at the front of the door trim panel. Remove by prying at its rear edge.
  6. Remove the red courtesy reflector from the lower tail of door. Disengage by prying at the screwdriver notch at the bottom of the reflector.
  7. Remove the flag trim panel from the door by prying it off at the 2 attachment clip points.
  8. Remove the 7 screws attaching the door trim panel to door:
    1. One screw is located at the lower rear screw pocket.
    2. Three screws are located along the bottom of the door.
    3. One screw is located inside the handle opening.
    4. One screw is located at the upper front.
    5. One screw is in the pull cup.
  9. Disengage the 2 hidden clips attaching the rear of the trim panel; pry them off at the 2 attachment clip points.
  10. Lift the trim panel upward and away from the door, disengage the trim panel from the upper retainer channel.
  11. Disengage the clip attaching the latch linkage to back door handle.
  12. Disconnect the electrical connectors as necessary, including the lower foot light, if equipped.
  13. Remove the door trim panel from the door.
  14. Remove the water shield (water dam) from the inside of the door.

    b5ff0ae.jpg
    Fig. Remove the flag trim panel, door trim access cover, inside remote handle, and power door lock switch
  15. Raise the door glass.
  16. Remove the bolt and nut for the rear glass run channel and position the channel aside.
  17. Disconnect the lock rod from the lock button bellcrank.
  18. Disengage the lock and latch rods from the clips on the inner door panel.
  19. Disconnect the lock and latch rods from the outside door handle and the key cylinder at the door latch.
  20. Disconnect the wire connector from the power door lock motor.
  21. Remove the screws attaching the door latch to the door end frame.
  22. Remove the door latch and the power door lock motor from the vehicle.

    c5c04cf.jpg
    Fig. Expanded view of the door lock, latch, and linkage


    185c44d.jpg
    Fig. View of the door lock button, latch rod, lock rod, and door latch

Hope helps (remember rated this).

Jun 26, 2010 | 2000 Chrysler Sebring

1 Answer

Door lock assembly


Toyota Corolla 1988-1997 Repair Guide Door Locks - REMOVAL & INSTALLATION
(see Figure 1)
  1. Disconnect the negative battery cable.
  2. Remove the door panel and watershield. Remove the service hole cover.
  3. Disconnect the door outside opening linkage. Remove the two mounting bolts and remove the door handle if in need of replacement.
402f2b0.jpg

Fig. 1: Power door lock control system component locations
  1. Disconnect the lock cylinder control linkage.
  2. Remove the lock knob and the child protector lock lever knob.
  3. Remove the lock assembly retaining screws and remove the door lock. If equipped with power locks, disconnect the electrical harness.
  4. To remove the lock cylinder, remove the lock cylinder retaining clip and pull the cylinder from the door.
To install:
  1. Coat all the door lock sliding surfaces with multi-purpose grease.
  2. Install the outside handle with the two retaining bolts, if removed.
  3. Install the door lock solenoid linkage to the door lock.
  4. Connect the link to the outside handle.
  5. Install the lock knob and the child protector lock lever knob.
  6. Install the door opening control link tighten the mounting bolts to 48 inch lbs. (5 Nm).
  7. Install the door lock cylinder control linkage.
  8. Install the door panel and watershield.
  9. Reconnect the negative battery cable.

Hope help with this; remember rated this post and thank you for using Fixya.

May 20, 2010 | 1991 Toyota Corolla

Tip

How to Replace Door Locks in Avanti convertible ?


The procedure to replace the door locks in car is as follows:--
1) First of all carefully remove the arm rest and any speaker covers if speakers are connected.
2) Then remove the door panel. The door panel is connected by plastic clips.
3) Then remove the door handle screws with the help of screwdriver.
4) After the screws are removed the door handle will come out
5) Now the interior doors handle needs to be removed. the interior door handle is fitted by plastic clips you can use a pliers to pop out the plastic clip, then twist the clip to allow the interior door handle to swing free and easily come out.
6) Take the door handle out
7) Now in the door remove the rod from lock core.Then remove the two bolts holding the door handle assembly.
8) Now before removing the old door lock, please take note of the position in which it is placed. So while inserting new lock there is no problem about placing the new lock.
9) Insert the new lock carefully to the proper position. And reverse/refit all the parts which you removed while replacing the old door lock.
This will help. Thanks.

on Mar 25, 2010 | Avanti Convertible Cars & Trucks

Tip

How to Replace locks in Door Locks of Acura Integra car


The procedure to replace the door locks in car is as follows:--
1) First of all carefully remove the arm rest and any speaker covers if speakers are connected.
2) Then remove the door panel. The door panel is connected by plastic clips.
3) Then remove the door handle screws with the help of screwdriver.
4) After the screws are removed the door handle will come out
5) Now the interior doors handle needs to be removed. the interior door handle is fitted by plastic clips you can use a pliers to pop out the plastic clip, then twist the clip to allow the interior door handle to swing free and easily come out.
6) Take the door handle out
7) Now in the door remove the rod from lock core.Then remove the two bolts holding the door handle assembly.
8) Now before removing the old door lock, please take note of the position in which it is placed. So while inserting new lock there is no problem about placing the new lock.
9) Insert the new lock carefully to the proper position. And reverse/refit all the parts which you removed while replacing the old door lock.
This will help. Thanks.

on Mar 25, 2010 | Acura Integra Cars & Trucks

1 Answer

How do I replace the door lock actuator on a 1999 Mercury Villager w/o damaging the connecting rods and door track?


SECTION 501-14A: Handles, Locks, Latches and Mechanisms 1999 Villager Workshop Manual REMOVAL AND INSTALLATION Actuator —Power Door Lock, Front Removal
  1. Remove the front door latch. For additional information, refer to Latch—Front Door .
  1. Remove the power door lock actuator from the front door latch.
    1. Release the locking tabs.
    1. Remove the power door lock actuator from the front door latch.
583b623.gif
go here too

http://groups.yahoo.com/group/villagerquest/

Sep 26, 2009 | 1999 Mercury Villager

3 Answers

ELECTRIC DOOR LOCKS ONLY LOCK SOME TIMES


if you hit the lock button a couple times, will it finally lock?

If so, then you will need to take door cover off and lube up the connectors as they probably got corroded.

Aug 14, 2009 | 2000 Ford F350 Super Duty Super Cab

Tip

How to Replace Door Locks in Audi All road car?


The procedure to replace the door locks in car is as follows:--
1) First of all carefully remove the arm rest and any speaker covers if speakers are connected.
2) Then remove the door panel. The door panel is connected by plastic clips.
3) Then remove the door handle screws with the help of screwdriver.
4) After the screws are removed the door handle will come out
5) Now the interior doors handle needs to be removed. the interior door handle is fitted by plastic clips you can use a pliers to pop out the plastic clip, then twist the clip to allow the interior door handle to swing free and easily come out.
6) Take the door handle out
7) Now in the door remove the rod from lock core.Then remove the two bolts holding the door handle assembly.
8) Now before removing the old door lock, please take note of the position in which it is placed. So while inserting new lock there is no problem about placing the new lock.
9) Insert the new lock carefully to the proper position. And reverse/refit all the parts which you removed while replacing the old door lock.
This will help. Thanks.

on Mar 25, 2010 | Audi AllRoad Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Aston Martin Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

896 Answers

Are you an Aston Martin Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...