Question about 2006 Mazda RX-8

Open Question

Car wont start,would the intake manifold tuning valve have anything to do with it

I was driving and the car just shut down

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 43 Answers

SOURCE: the car ran fine yesterday. i changed the valve

First thing I'd do is check if everything was connected, vacuum lines, fuel lines, connectors, etc. If all good, check the fuses and fuel pump relay. My guess would be the vac line to the fuel pressure regulator.

Posted on Nov 22, 2009

Ad
  • 197 Answers

SOURCE: I have a 2004 mazda mpv 3.0 engine it shows code

do ou have dohc

if so sounds like the vvt actuator.....
just a thought!!

Posted on Feb 15, 2011

emissionwiz
  • 76682 Answers

SOURCE: I have a 2006 Mazda RX8 in the shop with a code

It is not that simple, mulipile issues can cause this code.

Posted on Sep 09, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code PO660 has come up. How do you fix it


code p 0660 refers to intake manifold tuning valve ,bank 1--circuit open===causes --wiring--intake manifold tuning valve
The fix will be a replace valve
the problem is to find it's location but if you talk with Mazda spares or service department , they should show you where it is located
a workshop manual would be a help as well

Feb 03, 2016 | 2003 Mazda MPV

Tip

How to remove/replace the Valve Cover Gaskets on a New Beetle car?


Replace the valve cover gasket if the valve cover gaskets are leaking or if they're worn. The procedure is as follows:--
1) First of all let the motor cool down if the car was recently driven. Then remove the air intake boot.The air intake boot ios attached to the engine's throttle body.
2) Carefully disconnect the throttle cable , hoses and electrical connectors located on the upper intake manifold.
3) Then disconnect the hard pipe that is connected to the EGR (exhaust gas recirculation) valve.
4) The EGR valve is located beneath the upper intake manifold.
5) Then remove the bolts from both the upper intake manifold and the manifold support bracket.
6) Now the upper intake main fold and lower intake manifold both have got loose as you removed the nut.
7) After that remove the upper intake manifold from the lower intake manifold. Carefully place clean rags over the intake runners to prevent anything from falling into the intake system.
8) Then you will have to disconnect the crank case breather valve on the valve cover.
9) Then remove the bolts from the valve cover and remove the reinforcing straps.
10) Then remove the camshaft belt cover and the dust shield from the back of the camshaft sprocket.
11) Now carefully remove the valve cover. Properly clean the old gasket material with gasket remover.
12) You can install a new gasket in the reverse procedure of removal.


This will help. good luck.

on Mar 09, 2010 | Volkswagen Beetle Cars & Trucks

1 Answer

Fault code p0161


code p0161 refers to intake manifold tuning valve --bank 1 circuit low===causes --wiring short to ground--intake manifold tuning valve

Jan 03, 2014 | 2003 Toyota Highlander

1 Answer

Manifold tuning valve circuit low bank 1.(code po661)


one of the intake manifold tuning solonoids is down and needs replacing, there are 3 of them, 1 blue, 1 white, 1 red. p0661 is the white one

Nov 26, 2013 | Mazda RX-8 Cars & Trucks

1 Answer

Noise inside my intake manifold on 1999 sl2 saturn


if it sounds like a rattle thats your p.c.v. valve did you have a tune up latley probaly changed then . if so thats ok.

Nov 21, 2012 | Saturn SL Cars & Trucks

1 Answer

Car shuttering when started,like its not tune,rev up and down.


idle control valve, remove top intake manifold to get to it. replace icv and two hoses going to it. anything else plastic or rubber that breaks along the way...replace that stuff too. plan on 3 trips. to the auto parts store the bmw dealer and hardware store.

Jun 07, 2010 | 2000 BMW 3 Series

1 Answer

Tune up


NOPE TUNE UP CHECK ALL ENGINE FLUIDS.CLEAN INSPECT BATTERY.TURN OFF RADIO FIRST BEFORE REMOVING BATTERY CABLES SO YOU WONT LOSE CODE.CHECK THE COOLING SYSTEM.CHECK ALL HOSES.CHECK FUEL SYSTEM.AND AIR FILTER.CHECK DRIVE BELT OR BELTS.REPLACE SPARK PLUGS + WIRES.YOU DONT NEED TO REMOVE INTAKE AND EXHAUST MANIFOLDS.

Apr 11, 2010 | 2004 Kia Sedona

2 Answers

Engine runs rough and want to die when i put it in gear or when slowing at an intersection some times it runs perfect but not for long i changed sending unit , filter , and complete tune up. sometimes...


This condition can be caused by a sludged up idle speed control valve and a dirty throttle valve, do the following procedure to correct this, if it still doesn't repair the problem have the idle speed control system tested by the dealer.

Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

Mar 03, 2010 | 1999 Chevrolet S-10 Pickup

1 Answer

1993 golf shuts down under hard


1 Inspect Carburetor Worn, Faulty or Damaged Carburetor. 2 Inspect Fuel Filter Clogged or Dirty Fuel Filter. 3 Inspect Intake Manifold Gasket Leaking, Worn, or Damaged Intake Manifold Gasket. 4 Inspect FreshAir Intake Hose Clogged or Damaged FreshAir Intake Hose. 5 Inspect Fuel Pump Low Fuel Pressure. 6 Inspect Fuel Injector Dirty or Worn Fuel Injectors.

Jul 02, 2009 | 1993 Volkswagen Golf

2 Answers

Crank and start but wont stay on


bad ignition,air flow sensor that keeps leaning out the mix and it stalls,bad iac idle control motor,start with a good tune up.cap rotor,wires plugs air filter and clean the throttle body.some honda cars have bad egr valves and the intake manifold has to come apart because it is plugged up inside with carbon.

Jun 07, 2009 | 1997 Honda Accord

Not finding what you are looking for?
2006 Mazda RX-8 Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...