Question about 2003 Saturn VUE

1 Answer

Removel of door panel

Need to fix window cant get panel off

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Saturn Master
  • 5,332 Answers

You will need to remove the outside panel to service the window or window regulator or the window motor. The outer panel is held in place with a dozen or so bolts that a male torx socket is needed to remove. You will first remove the trim piece that is on the upper back of the outside of the door, two screws. Then remove the window seal on the outside of the window. Then remove the outer door handle. Then remove the torx bolts and lift up on the door skin, you may have to wiggle a little to get it to pop.

The video is for an S-Series but the principal is the same. Good luck!

Posted on Apr 20, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power window switch DR DOOR REMOVEL


put a fork tool under the rear of the switch panel and carefully pry up and grab it with your hands and pull back and up at the same time to release the rest of the clips. do not pry on the front because there is a tab that goes under the door panel that will break off.

Aug 29, 2013 | 2009 Chevrolet Traverse

1 Answer

2000 Silvarodo 2500 extended cab rear door pannel removel?


they have alot of hiden screws if it has a speeker in the door panel take the cover of there might be screws under it then look at the bottom of the door panel there might be screws at botom under the door panel

Nov 21, 2010 | 2000 Chevrolet Silverado

1 Answer

Trying to take off the panel to the driver side rear door. How do you take off the door handle to remove the panel.


Removing door panels from auto's are all a little different, but very simular.
1) Locate and remove any, and all screws from the panel(if any, some door panels do not have screws).
2) After removing all screw's, you will want to disingage all of the pop clip's located out of site around the outside edge of the panel. For this you will need a panel and trim removel tool. It looks like screw driver except it has a forked end and is bent at 45% on the tool end. The tool can be priced as high as 40.00 from company's like Snap-on, or as inexpensive as 3.99 from company's like Harbor Freight. After you have the tool, simply place the forked end between panel and door, and gently pry up until you feel the pop clip release. Repeat this process for all clips.
3) Now make sure that you have all screws for things like window cranks removed, and be carefull of power window wire's and switches.
This should free the panel from the door. I hope this helps you.

Oct 24, 2010 | 2005 Chevrolet Uplander

1 Answer

Get rear interior door panel off , want 2 bang dent out of exterior door


you have screws to remove then you have plastic clips to take off you need a removel tool for clips

Nov 20, 2009 | 2004 Pontiac Grand Prix

1 Answer

Need a diagram of how the door panel comes off of a 95 chevy blazer. I need to remove the door panel to fix the lock assembly. Need to know if there are clips at the bottom of the door, or just the screws.


There will always be clips attached to the panel from the inside-after screw removal and window crank removal (window crank on mostly earlier models) You can start at a bottom edge with what i recommend a door panel removal tool-most auto parts store carry these. even if a clip falls out you can reinsert it.Also the door removel tool doubles as a window crank clip remover.

Sep 20, 2009 | 1995 Chevrolet Blazer

1 Answer

My 1994 vans right side front window does'nt work. I was wondering if you could tell me how to take the door apart to check the power window regulator and motor. The van also has power mirrors.


There is likely a bolt under the arm rest take that out but you need a door panel removel tool to pry the plastic pegs out so you don't brake them or you will have to replace them they brake very easily,it looks like a srew driver with a forked end. and if your switches are on the arm rest you have to pry it out carefully

Sep 01, 2009 | 1994 Chevrolet G20

1 Answer

Dismount door panel. VW Polo Net


Sounds like it is a broken window regulator. You will need to remove the door panel to fix it. Mine broke and I can actually pull the window up and it will stay until the vibrations of the freeway eventually make it slide back down again (this would be a temporary fix of course). Anyways, there are a couple screws behind the door handle I believe, and then some snaps around the edges, and some clips along the window line. You should get a Bentley's manual so you know exactly how to fix the window regular. 

Jun 15, 2009 | 1999 Volkswagen Jetta

2 Answers

Replace power window motor right side


I looked at one earlier and I believe that first obviously that you remove the inner door panel.There are screws all around the outer edge of door panel.Also there are two quarter inch screws that are above the handle in middle of door.Then you peel back carefully the water barrier that is stuck to door.You will see three holes in the centr of door.The screws are golden in color in those holes.I believe they are 9mm or its standard counterpart.You should be able to remove the motor by pulling straight back.Be careful because I believe once you pull it out the window will fall.I'm not sure.Unhook wire connector and reinstallation is reverse of removal.Good lick!!!!I haven't done one yet but I'm going to do one in a bit on a 2002 saBLE.My email is ctate2@stx.rr.com if you have any questions.I don't know much but I can help people with alot of things every once in a while.I hope you get it going.

Jun 10, 2009 | 2003 Chevrolet Venture Passanger

1 Answer

1997 SL Saturn Headliner Removel


search google for the saturn fourms they had detailed instructions with pics . The short answer is all plastic trim around the top or doors from the windshield to the back window. The top of the dash needs to come off too It just pops off pretty easy . all clips you can see when the trim is pulled back a bit from the bottom and use a screwdriver to pry the clip out or it will break . you need a star wrench set to remove the setbelt bolts. the passenger handle is a pain I cant remember that one .

Feb 20, 2009 | 1997 Saturn SL

1 Answer

Fusion door panel removel


There is a fastener behind a circle looking plug behind the inside door handle. Take a small flat screwdriver and pop it off. It will be a torx. The same as the other screws on the door panel. After removing all fasteners start with the bottom of the panel and get your fingers between the panel and pry ou there will be door fasteners that will pop releasing the door. Do this carefully.

Nov 08, 2008 | 2008 Ford Fusion

Not finding what you are looking for?
2003 Saturn VUE Logo

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...