Question about 2002 Land Rover Freelander

Open Question

02 freelander V6 misfire

Just fitted a new top hose to the freeloader, new inlet gaskets etc, all back together but i've now gained a misfire

Posted by Anonymous on

4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 9 Answers

SOURCE: I can't find the two rear timing belts freelander

I just did the timing belts on mine; there is one main timing belt that connects to the crank, water pump, tentioner, idler, and to the intake cams on each head. The small timing belts are at each head at the rear of the head where the intake cam belts to the exhaust cams. If you pay like $30 on website you can subscribe for an online repair manual for the vehicle; where they have instructions and diagrams. If you look on YOUTUBE under the search for "rover kv6 timing belt replacement" there is films on this engine.

Posted on Oct 27, 2009

Testimonial: "Hi, you answer is very helpful and thanks"

  • 136 Answers

SOURCE: have no timing marks and has come to me in kit

copy and paste this adress for pictures of timming mark tools this should show you where they line up.:

Posted on Nov 27, 2009

SOURCE: 2002 land rover freelander v6 awd.Back brake

I had this happen before......Have you checked the fuses? If good I remember the wiring going thru the turn signal switch and replacing it solved the problem.

Posted on Nov 16, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is the next step in diagnosing our Terracans electrical problem

code p1123 refers to long term fuel trim--additive--mixture too rich===causes-- HO2S--fuel pressure --fuel system---mechanical fault---ECM
check all wires and connections. With the mechanical fault I would be revisiting all the items you removed to get to the rocker cover to ensure that all the hoses and wires were correctly replaced and that the gasket has not been mis -fitted or squashed out from under the cover at some point

May 20, 2014 | Hyundai Terracan Cars & Trucks

1 Answer

Oil leaks from a freelander 2002 V6 2.5L engine block. I am told dorman Cup expansion plug/freeze plug spoiled. How do I solve this problem?

where exactley is it comming from is it from the rocker cover or the sump either way a new gasket will be needed check hoses around the carbs as well and cylinder head as gaskets can go but not all together but you get oil seaping out of cylinder head hope this helps ivan

Sep 25, 2012 | 2002 Land Rover Freelander

1 Answer

How to replace a thermostat on a 1998 lexus ES300

Trace the upper radiator hose from the radiator to where the hose connects to the engine block via the water inlet tube. Remove the hose from the inlet tube by loosening the band clamp by squeezing the two compression tabs together with a pair of pliers. With the compression tabs squeezed together, pull the hose off the inlet tube.

Remove the two bolts that secure the water inlet tube to the engine of the Lexus with a 12-mm socket. When used with a swivel, you can remove the bolts without removing the air compressor motor. Lift the water inlet tube off the engine. It's a tight fit but you can work the tube out without removing any engine components.

Pull the thermostat out of the engine. Place the new one in the engine. The end with the spring on it sits inside the engine.

Pull the old gasket off the engine and clean the surface. Place the new gasket on the engine.

Position the water inlet tube on the engine and bolt it into place.

Slide the hose onto the water inlet tube and secure it with the clamp.

Oct 09, 2010 | Lexus ES 300 Cars & Trucks

3 Answers

Where the thermostat is located on a 1993 maxima

Usually in any vehicle the thermostat is underneath the fitting either on the engine manifold or the block that is attached to the TOP radiator hose. 1 clamp, 2 to 3 attaching bolts for the fitting, a gasket and the thermostat. Just make sure to clean the mating surfaces well and install an new gasket with the thermostat.

applies most any automotive engine......

Feb 02, 2010 | 2000 Nissan Maxima

1 Answer

Have no timing marks and has come to me in kit form freelander v6 costumer tryed to do head gaskets themselves and cant put back together. wish i had never taken job on,

copy and paste this adress for pictures of timming mark tools this should show you where they line up.:

Nov 24, 2009 | 2002 Land Rover Freelander

2 Answers

1993 toyota camry change thermostat

You're going to lose some coolant, so have a bucket or other container ready. Follow the upper radiator hose to the point where it's connected to the engine. The hose is clamped to a metal housing which is bolted to the engine. Remove the bolts (not the hose) and lift the housing to expose the thermostat (may require a little prying with a screwdriver or similar tool). Note how the old thermostat is fitted (which end is up), lift it out of the engine, and then remove all traces of gasket from the housing and the engine. Install the new thermostat and gasket, replace the bolts, add coolant as necessary, and you're done.

Nov 05, 2009 | 1993 Toyota Camry V6

3 Answers

I can only find three spark plugs on my freelander v6 engin

  1. Disconnect battery earth lead.
  2. Remove engine acoustic cover.
  1. RH bank only: Release locking clips and disconnect multiplugs from plug top coils.
  2. RH bank only: Remove 6 bolts securing plug top coils to RH camshaft cover and remove coils.
  1. LH bank only: Noting their fitted positions, disconnect ht leads.
  2. Using a 16 mm plug socket, remove spark plugs from both cylinder heads.
  1. Set gap of each new spark plug to 1.00 mm .
  2. Fit spark plugs and tighten to 25 Nm (18 lbf.ft) .
  3. LH bank only: Connect ht leads.
  4. RH bank only: Fit plug top coils to spark plugs.
  5. RH bank only: Fit bolts securing plug top coils to RH camshaft cover and tighten to 9 Nm (6.5 lbf.ft) .
  6. RH bank only: Connect multiplugs to plug top coils and secure with locking clips.
  7. Fit engine acoustic cover.
  8. Connect battery earth lead.

Jun 04, 2009 | 2003 Land Rover Freelander

1 Answer

Misfire in plug 4 in a 2004 landrover freelander

if your losing a bit of coolent mayby its the inlet manifold gasket as they can leak and cause problems if not start with the plug.

Nov 29, 2008 | 2004 Land Rover FreeLander

2 Answers

2004 freelander

After removing the engine cover and disconnecting the battery ,disconnect the air pipes that run across the manifold , these are normally brittle so handle them gently , remove them by pushing the clip at the base of the pipe down while pulling the pipe out.Do this with the fuel pipes too .The inlet manifold is held on by 4 bolts found next to the inlet pipes.There is also a bracket behind the manifold held on by two philips screws.When you refit the new manifold , apply some rubber grease on the o-rings as not to pinch them.Get you radio code before you disconnect the battery.

Oct 19, 2008 | 2004 Land Rover FreeLander

Not finding what you are looking for?
2002 Land Rover Freelander Logo

Related Topics:

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides