Question about 1999 Chevrolet Cavalier

Open Question

Remove axle need to remove rear axle

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Rear Axle Removal

if you are talking about the axle seals, 1.REMOVE THE WHEELS.2. REMOVE THE DIFF COVER(slowly)3.REMOVE THE BRAKE CALIPER ASSEMBLY.4.REMOVE THE 8MM PIN IN THE DIFF CARRIER. 5.TURN CARRIER AND REMOVE THE LARGE PIN.6. FIRMLY HIT IN THE AXLE, A SMALL RETAINING C CLIP WILL FALL INTO THE DIFF HOUSING. DO THE SAME WITH THE OTHER SIDE. ( be careful if you have rear speed sensors remove it when you remove the brake calipers . you will break it when you are pushing in the axles.)7.pull axles and replace seals

Posted on May 30, 2008

  • 6982 Answers

SOURCE: Rear axle removal

Remove wheel, remove rear diff cover, remove small bolt that retains spider gear cross shaft in the carrier. Push axle in, remove "c" clip on end of axle and remove axle from housing. Reverse to replace. Only problem you may have is that sometimes small bolt is broken inside carrier. if broken you will need to drill a tiny hole into it and remove with tiny "easy out" or other similar device.
Do not turn carrier when shaft has been removed or spider gears will rotate and fall out!

Posted on Feb 24, 2009

  • 541 Answers

SOURCE: need to remove rear axle on 67 camaro can't locate c clips

some older cars do not have c lips. you need to jack up car and place on jack stands withe the whelles off the ground. remove rims/tires. remove drum brakes. remove rear end cover. you need a drain pan under it. you need the car in neutral. spin axle. look in rear end. posi or not you will see the large pin that goes through the middle of the diff. one end of the pin is held in by a bolt. reomve the bolt. spin the diff down. slide the pin out. in side the diff on each side are spider gears. with the pin out push the axle in. this will push the clip so you can pull it off of tha axle and spider gera. then pull axle out. noe an easy or claen job but very doable.

Posted on Dec 27, 2009

  • 14036 Answers

SOURCE: how to remove rear axle to replace axle seal?

YOU NEED A HAYNES OR CHILTON REPAIR MANUAL.TO REMOVE REAR AXLE YOU HAVE TO REMOVE REAR DIFFERENTIAL COVER AND GASKET.YOUR DIFFERENTIAL HAS EITHER PINION SHAFT LOCKING SCREWS OR C - LOCKS.THEY HAVE TO REMOVED BEFORE AXLE SHAFT WILL COME OUT.

Posted on Mar 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 jeep grand cherekee rear axle seal removel do i need to remove c clips in rear to remove axle


No.....after removing the brake caliper and rotor, Unbolt the axle retainer plate from the axle tube flange. You need a slide hammer to pull the axle out.

Mar 19, 2011 | 2004 Jeep Grand Cherokee

2 Answers

I have greese all over the rear brakes


Rear Axle seals are bad, they must be replaced. Good Luck

Jan 14, 2011 | 1993 Ford Econoline

1 Answer

Rear axle removal ? i want to take to replace two broken lug nut bolts


to remove the rear axle you will need to put the rear of the jimmy on jack stands off the ground and remove the wheels

then remove the rear drums or if you have disc brakes the caliper and rotor

next you will need to remove the rear differential cover

once you have removed the rear differential cover you will need to rotate the differential by just turning the rear axle to gain access to the lockbolt

using an 8 mm socket you should be able to fairly easily remove the lock bolt

once you have removed the lock bolt you will need to push the axle in from the side that the wheel gets mouted to and then in the rear differential remove the locking 'c' clip

once the locking 'c' clip is removed you should be able to pull the axle right out

installation is the reverse of the removal

keep in mind that after romoving the lock bolt you must make sure not to rotat the axle if you do you will mess up the allignment with the differential and axle and you will spend loads of time trying to re-allign it again

hope this helps

Aug 13, 2010 | 1996 GMC Jimmy

1 Answer

How to remove gears from differential on a 95 mustang v6


Removal
  1. Raise vehicle and place jackstands under rear frame crossmember. Lower the hoist so that rear axle housing is at suitable working height.
  1. Remove axle housing cover from rear axle housing and drain lubricant.
  1. Perform the inspection before disassembly.
  1. Remove rear wheels, rear disc brake calipers and rear disc brake rotors.
  2. Working through cover opening, remove differential pinion shaft lock pin and remove differential pinion shaft and differential pinion gears (4215). 3fdbe2c.gif
NOTE: THIS IS FREE INFORMATION!!!!
  1. Remove rear brake anti-lock sensor . Push axle shaft inward until u-washers at button end of the axle shaft are clear of side gear recess.
  1. stb~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage inner wheel bearing oil seals when removing axle shafts from rear axle housing. In addition, axle shafts should be completely removed from rear axle housing.
    Remove u-washers and pull axle shafts out of the rear axle housing. 85189ce.gif

Mar 25, 2010 | 1996 Ford Mustang

1 Answer

Need detailed manual or assistance in replacing left rear axle seal and bearing on 2005 GMC Sierra pickup with 5.3L engine and a 324 rear end


You'll need to remove the rear end cover, remove the pin in the center pumpkin, push axle toward the center of vehicle and remove the axle clip, pull out axle. You may need a bearing puller to remove bearing.

Mar 04, 2010 | 2005 GMC Sierra

1 Answer

How do I remove the rear axle from a 1970 Datsun PL 520. I need to change the wheel studs


I'm not familiar with the vehicle but a rear axle is a rear axle.Remove the cover on the rear end[drain pan in place].Roll the diff around till you find an anchor pin.Remove the pin and roll it around again until you can remove the "c" clip.Now the axle will come out.Are you sure you need to remove the axle?You may be able the beat the ild stud out and draw a new stud with a spcer and retighten the wheel bolt to pull it in place,just a thought.

Oct 26, 2009 | 2000 Datsun 510

1 Answer

1994 gmc rear axle removal how to


-Remove tire and brake drum
-put drain pan under axle housing
-remove rear axle housing cover (10 or 12 bolts)
-turn gear untiil the bolt for cross shaft shows and remov e the bolt
-remove the cross shaft.
-push axle in until you can remove "U" clip from axle and axle will pull out,
Remove seal, you need a pulller to remove axle brg.

Jul 26, 2009 | 1994 GMC Suburban

1 Answer

Replace left rear axle seal 1999 ford explorer


Axle Shaft Removal
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the differential housing cover (4033).
    1. Loosen the bolts and drain the lubricant from the rear axle housing (4010).
    1. Remove the bolts.
    1. Remove the differential housing cover.
Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Turning the differential case (4204) or an axle shaft (4234) with the differential pinion shaft (4211) removed will cause the differential pinion gears (4215) to fall out of the assembly and damage the components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  2. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the U-washer groove.
  3. Remove the U-washer (4N237).
  4. Push the axle shaft inboard.
  5. Remove the U-washer.
Reinstall the differential pinion shaft.
  1. Install the differential pinion shaft.
  2. Install the differential pinion shaft lock bolt finger-tight.
  3. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal (1177).
    Remove the axle shaft.
-----------------------------------------------------------------------------------------------------------------
Seal Removal
  1. Remove the axle shaft (4334). For additional information, refer to Axle Shaft in this section.
  1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the wheel bearing oil seal (1177) by itself. Always remove the rear wheel bearing (1225) and the inner wheel bearing oil seal at the same time.
    NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged with foreign material.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal together.
6c7eb46.gif Installation
  1. Lubricate the new rear wheel bearing.
    • For 4.0L SOHC and 4.0L EI with limited slip rear axles and 5.0L vehicles, use SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL-M2C192-A.
    • For 4.0L SOHC and 4.0L EI with conventional rear axles, use SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. Using the special tools, install the rear wheel bearing.

ece7d89.gif
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the wheel bearing oil seal.
c21e27d.gif
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

Feb 22, 2009 | 1999 Isuzu Rodeo

1 Answer

Bent right rear RH axle 2001 prerunner 2wd.


Hello, and welcome to FixYa. Let me assist you as follows:
Removing the rear axle shaft is realy quite easy.
Her is what you need to do:

Remove the wheel/tire.
Remove the rear brake drum.
Remove the brake line to the rear wheel cylinder and plug the line.
Remove the park brake cable.
Remove the entire rear backing plate assembly; no need to remove the rear shoes.
When the backing plate is off, the axle shaft slides out of the axle housing; there are no "C" clips to remove, like on a Chevrolet. The axle is not held at the differential in any fashion.
Note that if you replace the axle shaft, you will need a machine shop to press the wheel bearings & seals onto the new shaft.

If you have any further questions; please feel free to respond.

Thanks for choosing FixYa for assistance; the graciousness of a FixYa rating for my instructions would be greatly appreciated.
Thanks in advance.

Jan 25, 2009 | 2001 Toyota Tacoma

1 Answer

Need to know how to change rear wheel bearing in a 95 suburban


jack & support vehicle. remove rear axle cover drain fluid, removeleft rear tire drum/rotor brakes, remove bolt in axle housing that holds the 3/4 inch pin in place pull pin , push left axle shaft inwards and remove c clip from inside axle case,slide out axle shaft,remove seal,remove bearing and install in revers

Jan 16, 2009 | 2003 GMC Sierra

Not finding what you are looking for?
1999 Chevrolet Cavalier Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...