Question about 2005 Ford F 350 Super Duty

Open Question

How to bleed abs brakes 2005 ford f-350 - 2005 Ford F 350 Super Duty

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Brian032472
  • 150 Answers

SOURCE: bleeding abs brakes

Manual

WARNING: Brake fluid contains polyglycol ethers and polyglycols. Avoid contact with eyes. Wash hands thoroughly after handling. If brake fluid contacts eyes, flush eyes with running water for 15 minutes. Get medical attention if irritation persists. If taken internally, drink water and induce vomiting. Get medical attention immediately.

CAUTION: Do not allow the brake master cylinder reservoir to run dry during the bleeding operation. Keep the brake master cylinder reservoir filled with the specified brake fluid. Never reuse the brake fluid that has been drained from the hydraulic system.

CAUTION: Brake fluid is harmful to painted and plastic surface's. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water.

NOTE: When any part of the hydraulic system has been disconnected for repair or installation of new components, air can get into the system and cause spongy brake pedal action. This requires bleeding of the hydraulic system after it has been correctly connected. The hydraulic system can be bled manually or with pressure bleeding equipment.

  1. Clean all dirt from and remove the brake master cylinder filler cap and fill the brake master cylinder reservoir with the specified brake fluid.

  2. Place a box end wrench on the RH rear bleeder screw. Attach a rubber drain tube to the RH rear bleeder screw and submerge the free end of the tube in a container partially filled with clean brake fluid.
  3. Have an assistant pump the brake pedal and then hold firm pressure on the brake pedal.
  4. Loosen the RH rear bleeder screw until a stream of brake fluid comes out. While the assistant maintains pressure on the brake pedal, tighten the RH rear bleeder screw.
    • Repeat until clear, bubble-free fluid comes out.
    • Refill the brake master cylinder reservoir as necessary.
  1. Tighten the RH rear bleeder screw.
  2. Repeat Steps 2, 3, 4 and 5 for the LH rear bleeder screw.
  3. Place a box end wrench on the RH front disc brake caliper bleeder screw. Attach a rubber drain tube to the RH front disc brake caliper bleeder screw, and submerge the free end of the tube in a container partially filled with clean brake fluid.
  4. Have an assistant pump the brake pedal and then hold firm pressure on the brake pedal.
  5. Loosen the RH front disc brake caliper bleeder screw until a stream of brake fluid comes out.
    • While the assistant maintains pressure on the brake pedal, tighten the RH front disc brake caliper bleeder screw.
    • Repeat until clear, bubble-free fluid comes out.
    • Refill the brake master cylinder reservoir as necessary.
  1. Tighten the RH front disc brake caliper bleeder screw.
  2. Repeat Steps 7, 8, 9 and 10 for the LH front disc brake caliper bleeder screw.

Posted on Nov 08, 2008

Ad
emissionwiz
  • 76164 Answers

SOURCE: 1993 Ford E 350 abs light will not turn off on ford .

the system has self test capabilities and can store a trouble code, have it tested the code will tell u what sensor circuit the fault exists in.

Posted on Mar 25, 2009

  • 202 Answers

SOURCE: how do you bleed the front brakes on a 2005 ford taurus

If the car has ABS, you will need to bleed it there also.

Posted on Mar 26, 2009

c17hydro
  • 2984 Answers

SOURCE: how to bleed the brakes for 2001 ford taurus

Please don't forget to rate:


Bleeding The Brake System Bleeding When any part of the hydraulic system has been disconnected for repair or replacement, air enters the lines causing spongy pedal action (because air can be compressed and brake fluid cannot). To correct this condition, it is necessary to bleed the hydraulic system to ensure all air is purged.
Always begin bleeding the brake system from the furthest wheel cylinder or caliper from the master cylinder; the right rear.
NOTE: The right side of the vehicle is the passenger side. The sides of the vehicle are determined from the driver's perspective. This reference is taken from sitting in the driver's seat, facing forward.
Maintain a full reservoir during the bleeding operation. Never use brake fluid that has been drained from the hydraulic system, or from an open container, no matter how clean it is. Always use brake fluid from a new, sealed container. The front and rear reservoir will drain as the front or rear brakes are bled.

  1. Park the vehicle on a level surface. Place the vehicle in PARK (automatic) or REVERSE (manual) with the engine OFF, and apply the parking brake. Chock the rear wheels to prevent vehicle movement. NOTE: Wheel chocks may be purchased at your local auto parts store, or a block of wood cut into wedges may be used.
  2. Loosen the lugnuts from all four wheels, but do not remove the lugnuts until the vehicle is raised and supported properly.
  3. Use an approved jack and raise the vehicle high enough to place jack stands under all four corners of the vehicle. Place the jack stands under the frame or axles of the vehicle. Ensure that the front of the vehicle is raised higher than the rear.
  4. Remove the wheels from the vehicle.
  5. Clean all dirt from around the master cylinder fill cap. Remove the cap and fill the master cylinder with brake fluid until the level is within 1/4 in. (6mm) of the top edge of the reservoir.
  6. Clean the bleeder screws at all four wheels. The bleeder screws are located on the back of the brake backing plate (drum brakes) and at the top of the brake calipers (disc brakes).
  7. Attach a length of rubber hose over the bleeder screw and place the other end of the hose in a plastic jar.
  8. Have an assistant place and hold pressure on the brake pedal.
  9. Open the bleeder screw 1/2 - 3/4 turn. As the bleeder is opened, the brake pedal will travel to the floor. Have the assistant inform you when the pedal has bottomed out. NOTE: Do not remove pressure from the brake pedal once it is bottomed out. No movement to the pedal should occur until the bleeder is closed and the assistant is made aware of the situation. Failure to do this will draw more air into the system.
  10. Close the bleeder screw and tell your assistant remove their foot from the brake pedal. Continue this process to purge all air from the system.
  11. When bubbles cease to appear at the end of the bleeder hose, tighten the bleeder screw and remove the hose.
  12. After bleeding each wheel, check the master cylinder fluid level and add fluid accordingly.
  13. Repeat the bleeding operation at the remaining three wheels, ending with the one closet to the master cylinder. The pattern is, RR, LR, RF, LF.
  14. Fill the master cylinder reservoir to the proper level and install the reservoir cap.

Posted on Jul 22, 2009

alicantecoli
  • 22156 Answers

SOURCE: Brakes engaging without pressing the pedal

this is a simple job of adjusting the rod on the end of the servo that pushes the master cylinder .remove master cylinder and with help push the brake pedal down and then screw the end of the shaft in a mm or so .This will cure your problem.

Posted on Sep 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check master cyclinder booster


Jim, Bleeding brakes 1999 Cadillac Deville.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
http://www.autozone.com/repairguides/DeVille-Eldorado-Seville-1999-2005/Anti-Lock-Brake-System/Bleeding-the-ABS-System/_/P-0996b43f80cb4368
Bleeding ABS Brake Systems
How to Bleed the Master Cylinder and Brake System

Aug 22, 2016 | 1999 Cadillac DeVille

1 Answer

Bleed brakes for 2005 prius


release? explain what that means.
what parts were disconnected? MC, tell what you did.
brakes good, bleed, no bad
brakes bad, parts pulled, now bad bleed,???? just a clue.here.
if you open a fitting north of the ABS main unit, you will be in trouble.


did you read the FSM on PRIUS< if not why not>?
got ABS,? sure...
some cars with ABS, have very specail rules and steps for
bleeding ABS. , including factory scan tools that must modulate
the ABS solenoids to clear air !
RTM.
or alldata.com/
i bounce in and read now for you.
it says.
Bleeding the brakes requires the use of the Toyota Hand-Held tester, or other appropriate scan tool. Follow the operating procedures of the Toyota Hand-Held tester, or other appropriate scan tool when bleeding the hydraulic brake system.

Before fiddling any car with ABS, google your car
see what others did wrong.... save lots of grief.
and a tow to a shop.


Dec 22, 2013 | 2005 Toyota Prius

1 Answer

Bleeding brakes, right rear still has air, ford 350 2001


You need to bleed the Rear wheel ABS unit first. It is mid vehicle, driver's side frame rail I believe. Until it is bled, you won't get fluid to the rear wheels.

Oct 24, 2010 | Ford F-350 Cars & Trucks

1 Answer

Replaced master cylinder, front brake calipers and rear calipers,


BY TRUCK HAVING ABS BRAKE.YOU NEED A SCANNER TO BLEED BRAKES THE SCANNER HAS TO RESET OPERATION OF THE BRAKE HYDRALIC SYTEM BEFORE YOU CAN BLEED SYSTEM.

Jul 13, 2010 | 2005 Ford F 350 Super Duty

1 Answer

Brakes engaging without pressing the pedal


this is a simple job of adjusting the rod on the end of the servo that pushes the master cylinder .remove master cylinder and with help push the brake pedal down and then screw the end of the shaft in a mm or so .This will cure your problem.

Sep 01, 2009 | 2005 Ford Five Hundred

1 Answer

On a 2003 ford ranger is there a different method of bleeding the brakes if the truck is equipped with ABS?


start with the wheel furthest from the abs unit.it just takes longer to do.it also depends on whether the system was completely drained or not.the best way for you to do it is get the copy of the procedure from the shop manual from ford.the best way is to have fresh fluid pumped into the resovoir,and drained one wheel at a time .

Jun 12, 2009 | 2008 Ford F-350 Super Duty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...