Question about 2008 Chrysler Pt Cruiser

1 Answer

2008 PT Crusier will not start. The coil is not sending power to the spark plugs. Brand New Coil, all fuses are good. New Camshaft sensor.... Still hunting the problem, any suggestions....

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chrysler Master
  • 44,621 Answers

Check that the immobiliser is operational. Check that power is getting to the coil ( ign fuse ). Check power from run position on the ignition switch to coil.

Posted on Apr 19, 2014

  • 1 more comment 
  • Helirush
    Helirush Apr 19, 2014

    Power is getting to the Coil. Just not getting Spark to the plugs...

  • Helirush
    Helirush Apr 19, 2014

    All ASD relays and fuses are good. New Ignition Coil, New Cam and Crankshaft sensors.

  • Bill Boyd Apr 20, 2014

    If the power is getting to the coil(12 volts or 7.5 volts depending on the coil specs coil) check that you are getting power out of the coil to the ignition module in the distributor . That unit may be faulty and not creating the pulse at the correct timing to induce the high voltage from the coil to the plugs.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
johnny5846
  • 379 Answers

SOURCE: where is the crankshaft sensor on a 2002 pt crusier

0eda6e7.jpg

looks like its above the axel on the engine side . above oil filter . you should be able to find it from there , best picture i could find .

Posted on Jan 06, 2009

blueextc3221
  • 15935 Answers

SOURCE: Crankshaft Position Sensor location 04 PT Cruiser

It is located behind the **** of the starter on the front of the engine starting in '03 the 2.4 lt was changes the repair manual failed to update this..you may sneak it out with small fingers with out pulling out the starter.

7e1821a.jpg

Posted on Feb 08, 2009

polarcycle
  • 1392 Answers

SOURCE: replace crankshaft sensor

Crank sensor on that car should be located near the pulley end of the motor, and near the firewall side. Fairly easy to get to.

Posted on Mar 06, 2009

  • 1 Answer

SOURCE: PT Cruiser 2003 died while driving, no spark from new coil

check the wireing harness under the car that goes th crank sensor and altnator it has been known to drop and rub tha passanger side axile and cut through sensor wire i had this happen on mine put the wires back toghter it started up and has no more problem .oh. please tie the harness up out of thr way i put mine th the oil cooler bolt

Posted on Mar 17, 2009

  • 295 Answers

SOURCE: 2001 PT crusier sunroof will not close, motor must

The motor is gone and the switch could be gone too.

I would replace both to be on the safe side.
The switch is not that expensive. The motor is more expensve.

Posted on Apr 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 chryser pacifica coil not firing coil is good


Do you have engine management light lit up on the dash?

Dec 22, 2016 | Cars & Trucks

1 Answer

I have power to my coil but none coming out on my 84 351 Windsor brand new distributor coil is good module came on new distributor I need help ?


Since the coil is getting power you need to get a spark tester or pull a cord of one spark plug and lay it on the engine and have some crank the engine. You should see and hear a spark. If not check fuses and check the ignition module - that is the device that tells the the coil to send a spark. You could also remove the wire from the coil to the dist cap and look for a spark.

Jan 04, 2016 | Cars & Trucks

1 Answer

No Spark


The relay for the fuel pump is working but have you checked that the pump is actually pressurising the system . Next you have power at the coil but is it getting to the spark plugs from the distributor.

Feb 15, 2014 | 2003 Chrysler PT Cruiser

2 Answers

It turns but it wont start,it has gas and power


Pull off the coil ignition cable at the distributor and check for spark coming out of coil when cranking engine over. Use a heavy rag or glove to hold the wire 1/4 inch from a metal ground. Should see a strong blue spark when cranking to verify ignition is good. If no spark, check for battery voltage to coil on the coil primary. If you have current to the coil, suspect a bad coil, ignition module, crank position sensor, or cam position sensor, or pcm. The coil, ignition module, and sensors can be tested before replacing.

Jan 29, 2013 | Cars & Trucks

2 Answers

2008 pt cruiser - check engine light came on, within minutes it started to "power down" and and died. Won't start. What could cause this? BTW have changed spark plugs, camshaft sensore, cranks


My PT did that when my timing belt broke. It cost $500.00 to replace it. If it is broken, be ready to have some motor work done. I had to have to values replaced at a cost of $900.00. If your timing belt is not broken then check the alternator and battery. I was riding down the road and my PT shut all the way down and would not start. I had to leave it beside the road. It was my alternator. It gave me no warning.

Dec 04, 2012 | 2008 Chrysler Pt Cruiser

1 Answer

98 kia sephia


code scan vechicle for faulty crankshaft sensor,camshaft sensor.check ignition fuse make sure ignition coil and ignition module getting power.because if power going to both either one of those could be faulty.

Nov 14, 2011 | Cars & Trucks

1 Answer

2003 dodge stratus has no spark. already replaced coil pak


CHECK IGNITION COIL FUSE.IF FUSE OKAY.YOU REPLACED COIL POWER TRANSISTOR. OTHER POSSIBLE CAUSES YOU NOT GETTING SPARK COULD BE FAULTY CAMSHAFT SENSOR AND CRANKSHAFT SENSOR ALSO FAULTY PCM.BEST TO CODE SCAN CAR BEFORE BUYING NEW PARTS.

May 03, 2011 | Dodge Stratus Cars & Trucks

5 Answers

PT Cruiser 2003 died while driving, no spark from new coil


Hello, I hear that pt quit while driving and you heard a thump,and you replaced the battery and coil and still no fire. Well it sounds like you have timing belt that broke it will keep it from firing at the coil if broke. Remove oil fill have someone spin engine over and see if camshaft turns if not turning the belt is broken. Please rate this answer, Thank you.

Feb 23, 2009 | 2003 Chrysler PT Cruiser

1 Answer

The car is running on 2 cylinder,


If you have no spark on the coil pack for these cylinders, try scanning the car to see if you get codes for a camshaft positioning sensor or crankshaft positioning sensor.

Dec 16, 2008 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...