Question about 1994 Toyota Camry

1 Answer

Egr erg code changed all componets with egr cleared code lite came back on

Posted by on

  • Wayne Fraser Apr 20, 2014

    A sticky Egr valve will cause a vacume leak . Which will cause the same code . Make sure there is nmo other vacume leaks.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Contributor
  • 42 Answers

Remove Negative Battery cable. wait a few minutes. Re attach

Posted on Apr 19, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Egr lite


sometimes the egr ports get clogged and you have to clean them out

Apr 19, 2014 | 1994 Toyota Camry

1 Answer

I have a 91 pontiac grand am with a 2.5 liter engine. My check engine light keeps coming on. The code says the problem is the egr circuit. My egr is vacumn actuated and has no eletrical connector. Where...


Take off erg valve and clean. Also take wire brush or used air compressor on its highest setting and blow out erg valve and egr housing areas

Aug 30, 2013 | Cars & Trucks

1 Answer

Will a bad egr sensor cause 2002 ford windstart to run bad in the rain


Before replacing it, disconnect the sensor with the engine off and spray WD-40 on the connection. Then reconnect and try it. You can disconnect the battery for 10 minutes to clear the Code.

Mar 18, 2013 | 2002 Ford Windstar Cargo

1 Answer

I have a 2001 Nissan Altima & my Service Engine Soon lite comes on. When checked these are the error code's; P1441 & P400. So far I put in a new EGR but still the lite goes back on. Please help...


On the nissan is there a swirl chamber code that comes on also, If it does then its truly a EGR code, but if the code is 1441 and 400 then its not the EGR, 400 is the EGR system not the EGR you r fix and solution is to solve P1441 the 400 is for function only. the failure is 1441 here is the definition Fuel filler cap, replace your gas cap and if its the type that click as you close the cap make sure it does Leave the EGR alone

Jun 13, 2011 | Nissan Altima Cars & Trucks

1 Answer

I am getting check engine codes that read EGR Flow CKT RNG/Perform and Engine Oil Pressure Switch CKT and EGR Closed Position/Perform


Replace what ever the codes say needs replaced,,,start with the ERG,,,Than run the scan again, if that engine oil switch comes up after you replace the ERG than replace it. Always clear the codes after you read them.

Mar 07, 2011 | 2001 Chevrolet Monte Carlo

1 Answer

Check engine light on, Dtc shows erg insufficient flow, changed erg control solenoid and dpfe unit


Hello, since I do not know if you cleared the computer on your vehicle, the first thing I will remind you of is to clear the computer after making repairs. The Errors can continue to show for 25-35 Startups after the problem is fixed. Both Autozone and Oreillys will scan and clear your computer for free.

Next, usually on older 4.6 V-8s' but on some other models the EGR passages below the Airhorn would clog with carbon. All you need to do is remove 8 bolts and clean the groove under the Airhorn gasket and then replace the gasket. Many, many times it is not necessary to replace any other parts.

What happens is the Diagnostics are wrong because they do not measure EGR flow at the source. Flow is measured after the EGR Valve, and after all of the Solenoids. Obviously all the parts down the line can't work if there is no flow from the manifold to go through them. Quite a money maker for the Auto guys.

I hope you find my solutions very helpful in solving your problem.

Jan 06, 2011 | Ford Expedition Cars & Trucks

1 Answer

I have a 2000 Honda Accord V-6 that had an engine light on code


check egr ports may be filled with **** or egr might be full of **** and need clean

Jan 08, 2010 | 2000 Honda Accord

1 Answer

Need a wiring diagram for a 1998 toyota camry for the vsv. replaced the transducer and vsv still getting code p0401 erg flow insufficient. any suggestion?


Start car with egr disconected. You should hear a sucking noise from said hole. If not you must clear this hole and there is your problem. If it is open then all thayt is left is the egr valve itself. hth

Oct 06, 2009 | 1998 Toyota Camry

1 Answer

Blocked Passage on ERG System, or Failed ERG Valve, or ERG solenoid Faulty


Very common on Ford engines with EGR codes is the tube inside the intake manifold that takes unburned exhaust gasses and recirculates them back into the engine for reburning,the tube becomes restricted from hydrocarbons and just plugs up.The intake manifold and tube has to be removed and thoroughly cleaned.

Jul 26, 2008 | 2000 Ford Focus

Not finding what you are looking for?
1994 Toyota Camry Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...