Question about 2003 Nissan Altima

1 Answer

Injecting but won't start

Will only start with easy start once running its ok

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Is the check engine light on?
Do a compression test on all cylinders.
First Check the condition of the spark plugs and wires. Fouled plugs
could cause hard starting.
Check ignition timing.
Check for vacuum leaks. Replace cracked and worn vacuum lines.
Does the Fuel filter have more than 50000 miles. I believe on that model year, its at the firewall close to the brake vacuum booster.

Posted on Apr 19, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I fix and 97 GMC 1/2 ton with a 350 vortec. Runs great once running. Sat for 5 years. If sits more than 5 minutes wont start without shot of starer fluid


have you changed the fuel filter and emptied the gas tank and put fresh gas in? Stale gas will not start as well as fresh gas and there could be water from condensation in the tank.

Mar 29, 2015 | 1997 GMC Sierra

1 Answer

Fuel tbi strting issue


Verify fuel pressure to the throttle body, if ok, then with the key on check for 12v at the injectors , if not , check fuses, if ok, check for injector pulse. disconnect injector connector , jump the two leads with a noid light or test light and have someone crank the engine, bulb should blink.

Dec 22, 2013 | 1992 Cadillac Fleetwood

1 Answer

Ignition modules locked


Hi!!! I'm having problems with my car: when I run it for a while and turn it off and try to start it again, it wouldn't start. It cranks but it does not start right away.
However, there is gas injecting into the chamber.

Sep 06, 2012 | 2003 Pontiac Aztek

2 Answers

Will start but it won't stay on once I step on the


not getting air or exhaust ....its being 'choked'

Nov 01, 2011 | 1989 Jeep Cherokee

1 Answer

When my buick century 1995 is cold it will start but won't rev up. once it is hot it runs okay


Number of possibilities. See if you have any diagnostic codes stored. Could be throttle position sensor, coolant temp. sensor, hard to say. I would start with the codes. Does it start easy when warmed up, and run good? Boy, I just don't know.

Oct 30, 2011 | 1995 Buick Century

1 Answer

When warm it idles rough and is hard to start


When the engine is cold, turn the key 2-3 time w/o starting the engine. What you do there is injecting fuel through the starting valve to get started. Normally this is performed by the remaining pressure in the system. Then turn another time and start the engine. If it starts easy then the fuel pump, which has a valve preventing back-flow, is the problem. However if this is the case the car should start quite ok after a stop shorter than say 10-20 minutes.
In case this wont be it, then it could be a problem with the cold start valve, which is a electrically activated valve. The problem might be that this valve does not close completely and leaks extra fuel in the intakes which than would influence the idle. You wont feel it driving, other than good pickup and lower gas mileage.

May 18, 2011 | Oldsmobile Silhouette Cars & Trucks

2 Answers

Mits Lancer GLXi 1996 Model .. Can't Start


Can you be more specific. Did you do any work on the car or did this just happen??How do you know its injecting fuel?? Did you smell fuel in the exhaust.???

Apr 26, 2010 | 2002 Mitsubishi Lancer

2 Answers

Just got an 1998 Isuzu Wizard (diesel), some times


It sounds like the fuel is gelled, is it cold where you are and what are running for fuel? If your in freezing weather you should be running blended fuel, straight No.2 will gel at about 25 degrees (F). Take a hair dryer or heat gun and warm the fuel filter up. Or if you can get in warm garage and get it started thin the diesel with kerosene, about 2 gallons to 20 gallons of diesel. Then drive it for at least five miles so the kerosene gets circulated through the system. I've used gasoline to do this too, but only use about 1 gallon to 20 gallons of diesel.

Jan 08, 2010 | 1998 Isuzu Trooper

Not finding what you are looking for?
2003 Nissan Altima Logo

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...