Question about 1989 Ford F 150

1 Answer

89 f-150 no power to fuel pump

Have checked fuse .

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 250 Answers

If it takes buying a set of fuses (which it might not even be a normal/buss fuse anyways), then I think it's worth it.
Most autoparts stores will help you out with locating where the part goes.

Posted on Jun 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car will not start it cranks but will not turn on. So far I have changed the crank sensor I also have no spark to coil packs or spark plugs Fuel pump does not turn on when I turn the key. What is the...


Begin by checking fuses. Ignition, efi, fuel pump fuses. When key turned to on, do the warning lights and gauges work? That verifies switch has power and is sending power out. With key on, the coil primary wire to coil packs should have voltage.

No spark and no gas? Fuel pump fuse good? I think I would use a test light or multimeter to check that fuel pump fuse terminal has power to it with key on. If that's good, pull connector off at fuel tank and check for a voltage signal on fuel pump wire when the engine is cranking-if good signal, fuel pump needs taken out for replacement or inspection. If no signal check that fuel pump relay has power to it. With key off, pull the relay and check that one terminal has power to it-the feed wire for the pump. If no power signal at all, check maxi fuses or fusible links for a failure.

Sep 04, 2013 | Cars & Trucks

1 Answer

No power to fuel pump or pump fuse on a 1996 saturn sl1. whats up?


The fuel pump fuse gets its power from the fuel pump relay, which is located in the Instrument Panel Junction Block.

The fuel pump relay gets its ground from G102, which is located just forward of the left strut tower.

The fuel pump relay gets its power from the Powertrain Control Module Connector "C" Pin 10 ( DARK GREEN/ WHITE wire) for the primary side of the relay.

The sencondary side (the side that provides power to the fuel pump fuse) of the fuel pump relay gets its power from the IP BATT Fuse (30 Amp) HOT AT ALL TIMES in the underhood fuse block.

This should be enough information to figure out why your fuel pump is not getting power. Let me know what you find.

Apr 14, 2012 | Saturn SL1 Cars & Trucks

3 Answers

No power to fuel pump on 1999 crown victoria


Hello abzalkhan193
Heres a few things to check that could cut power to the fuel pump. The fuel pump inertia shutoff sw
in the trunk on the left side, there is a reset button on the switch if you push the button down and
you hear/feel a click then the switch was tripped and you just reset it. The switch's job is to cut off
the fuel in case of an accident. Next, the fuel pump fuse located in the battery fuse block under the
hood on the right fender well, fuse #1 20amp fuse. Next, the fuel pump relay, the relay is located in
relay center on the left fender well. Hope this is helpful.

Mar 11, 2011 | 2001 Ford Crown Victoria

2 Answers

No power to fuel pump to make it work in gas tank


Have you checked the fuse/relay or the reset button (if equipped)?

Mar 03, 2011 | 1987 Nissan Pickup

1 Answer

00 jeep grand cherokee fuel pump is not getting no fire. checked the fuse breakers even changed the computer. still no fire to the pump


When you state "checked the fuse breakers" did you check for power at the fuse block. Start checking power from the fuse box, then check for power at the end that plugs into your fuel pump. The switch will have to be on for the power to be present. My main concern is, if the fuel pump went out. But it's easier to check for the power first. If you're getting power from all sources, then the fuel pump has went out most likely.

May 11, 2010 | 2002 Jeep Grand Cherokee

3 Answers

No power to fuel pump car was running fine just quit repalced fuel pump no power to pump, car will start when spraying starting fluid in to intake, is there a fuse ? also replaced ECM, fuel filter,...


Check for 12 volts power at the fuel pump harness. If no power is going to the pump, check the fuel pump relay. Also, check the fuel pump inertia switch. Ford usually has it on either inside left or right rear trunk fenders.

Apr 09, 2010 | 1987 Ford Taurus

2 Answers

1992 Buick Roadmaster no power to fuel pump. New fuel pump and changed the ecm ...please help


Theres a few more checks But i'm sure you checked the fuel pump fuse already ..Use a test light and check to see if the fuel pump relay is getting power from the supply and from the Ignition feed. should be a schematic on the underside of the relay..if no power from the feeds check for a blown or rotted fuseable link or a maxi fuse..good luck

Jan 27, 2010 | 1992 Buick Roadmaster

1 Answer

1997 Ford F150 Electric Fuel Pump will npt pump


Did you check the fuel inertia switch in the passenger side kick panel ?

The fuel pump is powered :
the fuse to the fuel pump relay.
The fuel pump relay to the fuel inertia switch
The fuel inertia switch to the fuel pump itself.

At the fuel inertia switch in the kick panel, power from the relay is the Dark Green w/ Yellow stripe wire and the pink w/ black stripe wire is the power. from the fuel inertia switch to the fuel pump.

If you jumper the fuel pump relay, you should hear it run. If not pull the fuel pump relay, and check the pins in the relay socket, pin 30 should be the power from the fuse.

50b0c31.jpg

If you have power at pin #30, jumper the relay socket as shown with the red line above, and check the dark green w/ yellow stripe wire at the fuel inertia switch for power.
Press the button on the top of the fuel inertia switch, and check for power leaving the fuel inertia switch on the pink w/ black stripe wire.

This is tests good, check for power at the fuel pump, same pink w/ black stripe wire.
Fuel inertia switch info is in the owners manual, If you did not get an owners manual with your truck ( purchased used ), you can download one from Ford :
https://www.fleet.ford.com/maintenance/owners_manuals/default.asp

Jan 03, 2010 | 1997 Ford F150 Regular Cab

1 Answer

New relay an new fuel pump no fire goin to fuel pump


Check fuel pump fuse, remember fuse send power to relay and relay sends power to pump, Check power wires to pump and make sure FUEL PUMP FUSE IS GOOD if not replace and take care of this problem. Good luck and thanks for using FIX YA.

Mar 25, 2009 | 1990 Ford F150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...