Question about 1996 Toyota Hilux

Open Question

3RZFE water leak timing belt cover water pump exploded view

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
satanchild30
  • 8 Answers

SOURCE: CHANGE WATER PUMP, TIMING BELT, AND

you need to check the radiator andf or the hoses from radiator and water pump.. you might to have to change one of them if not all of them to see if it still leaks

Posted on Mar 24, 2009

Ad
carputers
  • 255 Answers

SOURCE: water pump housing problems

your pump wep hole, bad pump not pep boys fault :( sorry just need water pump.

Posted on Sep 08, 2009

Testimonial: "sound like the problem to me too. they say they put a new pump in but I dought it...."

  • 1374 Answers

SOURCE: wife driving car and noticed water. thought it

Before you waste time and money you may want to have someone look at the vehicle because the belt may look fine but may have jumped a tooth and now you may have major engine problems.

Posted on Mar 28, 2010

SOURCE: 89 camry got water leaking from around water pump

Place a jack with suitable protection under sump so as not to damage sump and lift just a little to relieve just enough tension to remove through bolt onto body....Regards Johngee

Posted on Oct 06, 2010

skychief2001
  • 21873 Answers

SOURCE: toyota pickup antifreeze leak around timing belt cover

You won't really know until you can see the bottom of the pump. Most pumps have a "weep" hole where coolant will leak from if the seal goes bad. It can leak and still function without symptoms until the bearing goes.

Posted on Dec 15, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I align the timing chain on my Toyota Hi Lux 1998 3rzfe please?


should be alignment marks on the block or on the new belt. align the pulleys to match marks. don't forget to match up the water pump. next time get the tool that holds the pulleys in place before removing the belt.

Jul 11, 2015 | Toyota Cars & Trucks

1 Answer

Where is the water pump


Water Pump REMOVAL & INSTALLATION 5VZ-FE Engines Fig. 1: The water pump is located on the front of the engine block, behind the timing cover 93163p92.jpg
Fig. 2: Once the retainers are removed, pull the pump away from the block 93163p97.jpg
Fig. 3: Scrape any remaining gasket material from the block before installing the new pump 93163p98.jpg
Fig. 4: Water pump mounting bolt locations 93163p88.jpg
Fig. 5: Front view of the water pump and thermostat housing 93163p99.jpg
WARNING
This procedure requires the removal of the timing belt. This is an extensive procedure requiring precision work, particularly at assembly. For more information, refer to Timing Belt Removal and Installation. Do not attempt to remove the belt without consulting the procedure; extreme engine damage may occur. Fig. 6: Apply sealant to the areas shown 86823pi7.gif
Fig. 7: A and B bolt locations 86823pi8.gif
Fig. 8: Exploded view of the water pump arrangement — 5VZ-FE engine 93163g19.gif
  1. Drain the cooling system.
  2. Remove the timing belt. For additional information, please refer to the following topic(s): Timing Belt Removal and Installation.
  3. Remove the idler pulley.
  4. Remove the thermostat.
  5. Disconnect the oil cooler hose from the pump.
  6. Remove the seven bolts and the tension spring bracket and then remove the water pump. To install:
  7. Clean all parts well. It is good practice to carefully clean all threaded openings, especially those exposed to coolant to remove rust and scale so at assembly, an accurate torque reading is obtained. This is important since gasketless applications like this depend on even clamp loads from the fasteners to avoid distortion and leaks. Remove any old sealer (Toyota calls it packing) from the pump and mounting area of the engine. Keep oil off the mating areas.
  8. Apply Formed In Place Gasket (FIPG) sealer to the pump-to-block mating surface and then tighten the bolts marked A in the illustration to 13 ft. lbs. (18 Nm). Tighten those marked B to 14 ft. lbs. (20 Nm). NOTE: The parts must be installed within 5 minutes of application of the sealant. Otherwise you must remove and reapply the sealer.
  9. Connect the oil cooler hose.
  10. Install the thermostat with a new gasket.
  11. Install the idler pulley.
  12. Install the timing belt.
  13. Install the drive belts and adjust the tension.
  14. Refill the cooling system and check for leaks.
2RZ-FE and 3RZ-FE Engines
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. If equipped with an air conditioning compressor or power steering pump drive belts, it may be necessary to loosen the adjusting bolt, remove the drive belt(s) and move the component(s) out of the way.
  4. Remove the fluid coupling with the fan and water pump pulley.
  5. Remove the water pump. To install:
  6. Clean the gasket mounting surfaces.
  7. Install the replacement water pump using a new gasket.
  8. Install the water pump pulley and fluid coupling with the fan.
  9. Install the removed engine drive belts.
  10. Fill the cooling system.
  11. Connect the negative battery cable. Start the engine and check for leaks.
  12. Bleed the cooling system.
1FZ-FE Engine Fig. 9: Exploded view of the water pump mounting on the 1FZ-FE engine 86823pk0.gif
Fig. 10: Detach the oil cooler hose from the clamp on the fan shroud 86823pk3.gif
prev.gif next.gif

Jul 13, 2010 | 1997 Toyota RAV4

1 Answer

Change water pump on 1999 Century Buick


GM Century/Lumina/Grand Prix/Intrigue 1997-2000 Water Pump - REMOVAL & INSTALLATION

3.1L and 3.4L (VIN E) Engines
  1. Disconnect the negative battery cable.

  2. Partially drain the cooling system into a suitable container.
  3. Remove the drive belt guard.
  4. Loosen the water pump pulley bolts before removing the drive belt. This should help keep the pulley from turning as the bolts are loosened.
  5. Remove the drive belt. Please see .
  6. Remove the water pump pulley bolts and remove the pulley.
  7. Remove the water pump bolts and separate the pump from the engine front cover.

To install:

1430070.jpg

Fig. Exploded view of the water pump and front cover arrangement-3.1L and 3.4L (VIN E) engines
  1. Clean all parts well. Use care when scraping gasket material from the front cover and the pump. Do not gouge aluminum parts. Clean the bolt threads well. The torque specification is low and if the bolt threads are dirty, an accurate torque is not possible and leaks are likely to develop.
  2. Using a new gasket, install the water pump to the front cover. Install the cleaned and lightly lubricated water pump bolts. Torque to 89 inch lbs. (10 Nm).
  3. Install the water pump pulley and bolts and torque to 18 ft. lbs. (25 Nm).
  4. Install the remaining components in the reverse order of the removal process. When refilling the cooling system, use the proper mix of DEX-COOL® and water. Check for leaks.

3.4L (VIN X) Engine
  1. Disconnect the negative battery cable.
  2. Partially drain the cooling system into a suitable container.
  3. Remove the coolant recovery reservoir.
  4. Remove the drive belt. Please see .
  5. Remove the pulley bolts and separate the pulley from the water pump.
  6. Remove the water pump bolts and remove the pump from the engine.

91d51fb.jpg

Fig. Exploded view of the water pump mounting-3.4L (VIN X) engine
To install:
  1. Clean all parts well. Use care when scraping gasket material from the front cover and the pump. Do not gouge aluminum parts. Clean the bolt threads well. The torque specification is low and if the bolt threads are dirty, an accurate torque is not possible and leaks are likely to develop.
  2. Using a new gasket, install the water pump to the front cover. Install the cleaned and lightly lubricated water pump bolts. Torque to 89 inch lbs. (10 Nm).
  3. Install the water pump pulley and bolts and finger-tighten the bolts.
  4. Install the drive belt, then torque the pulley bolts to 18 ft. lbs. (25 Nm).
  5. Install the remaining components in the reverse order of the removal process. When refilling the cooling system, use the proper mix of DEX-COOL® and water. Check for leaks.

Hope this help (remember comment and rated this).

Apr 04, 2010 | 1998 Buick Century

1 Answer

How do I change a water pump on a 2004 kia sorento?


Kia Sorento 2003-05
Water Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

  9. dc45c19.jpg

    Fig. Water pump and timing belt assembly-exploded view

To install:

1016213.jpg

Fig. Water pump bolt locations
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. Refill the coolant.
  7. Run the engine and check for leaks.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

To install:


e9be8c3.jpg

Fig. Water pump bolt locations

596080e.jpg

Fig. Water pump O-ring installation
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. To adjust the drive belt tension, hang the belt on the pulley of the tensioner and install the tensioner.
    NOTE If the tensioner is already installed, loosen its mounting bolts to allow belt installation
  7. Install the drive belt.
  8. Adjust the belt tension to specification by turning the adjusting bolt clockwise or counterclockwise.
  9. Air conditioning belt tension should be 0.28-0.039 inch. Alternator belt tension should be 0.39-0.051 inch. Power steering belt tension should be 0.31-0.051 inch.
  10. Torque the tensioner assembly bolt to 33-36 ft. lbs. (45-50 Nm).
  11. Refill the coolant.
  12. Run the engine and check for leaks.

TY for using Fixya; remember comment and rated this.

Apr 01, 2010 | 2004 Kia Sorento

2 Answers

How to change water pump on toyota sienna


3.0L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the engine coolant.
  4. Remove or disconnect the following:
    Wiper and blade assembly Top cowl seal and panel Window washer hoses, from the ventilator louvers Left and right ventilator louvers Heater air duct Timing belt
  5. Mark the left and right camshaft pulleys with a touch of paint.
  6. Remove or disconnect the following:
    NOTE Be sure not to mix up the pulleys.
    Right and left camshaft pulleys bolts Pulleys from the engine
    No. 2 idler pulley by removing the bolt 3 clamps and engine wire from the rear timing belt cover 6 No. 3 timing belt cover-to-engine bolts Water pump nuts/bolts Water pump and gasket from the engine

    9c53b11.jpg
    Fig. Exploded view of the components to gain access to the water pump-3.0L engine


    cf2cc65.jpg
    Fig. Exploded view of the water pump and related components-3.0L engine

To install:
  1. Check that the water pump turns smoothly. Also check the air hole for coolant leakage.
  2. Apply liquid sealer to the gasket, water pump and engine block.
  3. Install or connect the following:
    NOTE After tightening the bolt, be sure the idler pulley moves smoothly.
    NOTE Be sure to align the knock pin hole on the camshaft pulley with the knock pin on the camshaft.
    NOTE Be sure to align the knock pin hole on the camshaft pulley with the knock pin on the camshaft.
    Water pump, using a new gasket. Tighten the nuts/bolts to 53 inch lbs. (6 Nm). Rear timing belt cover. Tighten the 6 bolts to 74 inch lbs. (9 Nm). Engine wire with the 3 clamps to the rear timing belt cover No. 2 idler pulley. Tighten the bolt to 32 ft. lbs. (43 Nm).
    Right-hand camshaft pulley, with the flange side outward.
    Tighten the camshaft bolt to 65 ft. lbs. (88 Nm), using the removal tools Left-hand camshaft pulley, with the flange side inward.
    Tighten the camshaft bolt to 94 ft. lbs. (125 Nm), using the removal tools Timing belt
  4. Fill the engine coolant.
  5. Install or connect the following:
    Heater air duct Left and right ventilator louvers Window washer hoses to the ventilator louvers Top cowl seal and panel Wiper and blade assembly Negative battery cable
  6. Start the engine.
  7. Top off the engine coolant and check for leaks.

Hope this help.

Mar 23, 2010 | 2004 Toyota Sienna

1 Answer

How do i install a water pump for an Isuzu Rodeo, V.7 3.2 liter


Isuzu_Rodeo_Rodeo_Sport_1997-2004
Water Pump - Removal and Installation

3.2L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Upper radiator hose Timing belt. Refer to the Timing Belt procedure. Idler pulley Water pump
To install:


d2081b9.jpg

Fig. Exploded view of the water pump mounting

3702807.jpg

Fig. Water pump torque sequence. Apply LOCTITE® 262 to bolt number 3 (arrow)-3.2L and 3.5L engines

NOTE Apply Loctite® 262 to bolt number 3 prior to installation.
  1. Install or connect the following:
    Water pump. Tighten the bolts in two passes, in sequence, to 18 ft. lbs. (25 Nm). Idler pulley. Torque to 38 ft. lbs. (52 Nm). Timing belt Upper radiator hose Negative battery cable
  2. Fill the cooling system.
  3. Start the engine and check for leaks.

3.2L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following: Negative battery cableRadiator hoseAccessory drive beltFront coverTiming belt. Refer to the Timing Belt unit repair section.Timing belt idler pulley Water pump
    Negative battery cable Radiator hose Accessory drive belt Front cover Timing belt. Refer to the Timing Belt unit repair section. Timing belt idler pulley Water pump

To install:

e6f48ad.jpg

Fig. Water pump bolt tightening sequence-3.2L engines
  1. Install or connect the following: Water pump. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm).Timing belt idler pulley. Tighten the bolt to 38 ft. lbs. (52 Nm).Timing beltFront coverAccessory drive beltRadiator hoseNegative battery cable
    Water pump. Tighten the bolts in sequence to 18 ft. lbs. (25 Nm). Timing belt idler pulley. Tighten the bolt to 38 ft. lbs. (52 Nm). Timing belt Front cover Accessory drive belt Radiator hose Negative battery cable

  2. Fill the cooling system.
  3. Start the engine and check for leaks.

Hope this help (remember rated and commento).

Mar 19, 2010 | 1997 Isuzu Rodeo

3 Answers

Toyota 4runner timing belt or chain?


60000 or 48 months on belt which is used on the 5VZ-FE motor. The 2RZ-FE and 3RZFE are chain and there is no clear information about changeing them as a maintenence. i hope this helps.

Nov 12, 2009 | 1998 Toyota 4Runner

2 Answers

Where is water pump located on 1997 nissan pick up truck


Several engines in here:

- 2.0L
b8ce1b5.jpg

View of the water pump mounting and O-ring-2.0L engine


- 2.4 L
81bf5ba.jpg

Exploded view of the water pump and mounting on the engine-2.4L engine


- 2.5L
21fb20c.jpg

View of the water pump mounting-2.5L engine


For remove in a 2.0L
  1. Disconnect the negative battery cable.
  2. Properly drain the engine coolant into a clean container for reuse.
  3. Remove the timing belt.
  4. Unfasten and remove the timing belt rear protective covers.
  5. Detach the hose from the water pump.
  6. Unfasten the water pump attaching bolts, then remove the water pump and seal ring.
To install:
  1. Thoroughly clean and dry the mounting surfaces, bolts and bolt holes.
  2. Using a new sealing ring, install the water pump to the engine and hand-tighten the retaining bolts.
  3. Attach the hose to the water pump.
  4. Fasten the timing belt rear protective covers, then install the timing belt and properly adjust the tension.
  5. Tighten the water pump bolts to 18 ft. lbs. (24 Nm).
  6. Install the timing belt cover and related parts.
  7. Connect the negative battery cable.
  8. Fill cooling system and check for leaks. Start the engine and allow to come to normal operating temperature. Recheck for leaks and top-off the coolant.

For more details about other engines, can visit autozone.com

Hope helped. Good luck.

Nov 02, 2009 | 1997 Nissan Pickup

1 Answer

How to change the water pump on a ford escort 1.3gle 1986 model


  1. Let me know if you cannot see diagrams(happens sometimes) or if you have any questions
Just to make sure. I assume that you are seeing coolant leakage from around the water pump assembly.

  1. Disconnect the negative battery cable.
  2. Place fender covers on the aprons.
  3. Drain the cooling system.
  4. Remove the accessory drive belts.
  5. Remove the timing belt cover.
  6. Use a wrench on the crankshaft pulley to rotate the engine so No. 1 piston is on TDC of the compression stroke.
Turn the engine only in the direction of normal rotation. Backward rotation will cause the timing belt to slip or lose teeth.
  1. Loosen the belt tensioner attaching bolts, then secure the tensioner over as far as possible.
  2. Pull the belt from the camshaft, tensioner, and water pump sprocket. Do not remove it from, or allow it to change its position on, the crankshaft sprocket.
WARNINGDo not rotate the engine with the timing belt removed or serious engine damage could occur. The 1.3L and 1.6L engines are of the "interference type," meaning it is possible for the valves to contact the pistons if their reciprocation is not carefully timed and controlled. An engine allowed to spin freely without the timing belt could bend valves and scuff pistons almost instantly.
  1. Remove the camshaft sprocket.
  2. Remove the rear timing cover stud.
  3. Remove the heater return tube hose connection at the water pump inlet tube.
  4. Remove the water pump inlet tube fasteners and the inlet tube and gasket.
  5. Unfasten the water pump to the cylinder block bolts and remove the water pump and its gasket.
0900c1528008b2ee.jpgFig. 1: If equipped, remove the cover from the water pump 0900c1528008b2ef.jpgFig. 2: Unfasten and remove the heater return tube hose connection at the water pump inlet tube nuts from the studs 0900c1528008b2f0.jpgFig. 3: Location of the water pump mounting bolts-1.9L engine 0900c1528008b2f1.jpgFig. 4: After unfastening the water pump retaining bolts, remove the water pump from the engine compartment 0900c1528008b2f2.jpgFig. 5: If you are reusing the old water pump, remove the gasket ... 0900c1528008b2f3.jpgFig. 6: ... and carefully clean both of the water pump mating surfaces using a gasket scraperTo install:
  1. Make sure the mating surfaces on the pump and the block are clean.
  2. Using a new gasket and sealer, install the water pump. Tighten the bolts to 30-40 ft. lbs. (40-55 Nm) on 1981-87 models, or to 15-22 ft. lbs. (20-30 Nm) on 1988-90 models. Make sure the pump impeller is able to turn freely.
  3. Install the water pump inlet tube and the inlet tube gasket and fasteners.
  4. Install the rear timing cover stud. Install the heater return tube hose connection at the water pump inlet tube.
  5. Install the camshaft sprocket.
  6. Install the belt from the camshaft, timing belt tensioner, and water pump sprocket.
0900c1528008b2f4.jpgFig. 7: Radiator hose-to- engine mounted water pump inlet tube-gasoline engines 0900c1528008b2f5.jpgFig. 8: Exploded view of common water pump inlet tube and related fasteners-non-A/C type 0900c1528008b2f6.jpgFig. 9: Exploded view of water pump and related components-1988-90 1.9L engineDo not rotate the engine with the timing belt removed.
  1. Tighten the belt tensioner attaching bolts, then secure the tensioner over as far as possible.
  2. Install the timing belt cover.
  3. Install the accessory drive belts.
  4. Refill the cooling system and reconnect the negative battery cable.

Nov 15, 2008 | 1983 Ford Escort Gt

1 Answer

Water pump


1. Drain the coolant and disconnect the coolant outlet pipe connection hose from the coolant pump. 2. Remove the drive belt and engine coolant pump pulley. 3. Remove the timing belt covers and the timing belt idler. 4. Remove the coolant pump mounting bolts, then remove the generator brace. 5. Remove the coolant pump assembly from the cylinder block. See an exploded view:
d0ab616.gif

Jun 27, 2008 | 1997 Hyundai Elantra

Not finding what you are looking for?
1996 Toyota Hilux Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...