Question about 2002 Mazda Tribute

Open Question

Transmission prlblems it is difficult to take off is like very heavy after while it stops turn it off and repeat the process

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake lights do not work,all outher lights work


adjust brake light switch which is located above brake pedal. depress pedal and screw the switch clockwise a complete turn then try your lights if not working repeat process until they come on

Mar 18, 2014 | 1998 Lincoln Town Car

1 Answer

Spongy clutch how to bleed clutch 2001 alero


The bleeder nipple is on the clutch slave cylinder on the bell housing. Fill the reservoir and have someone depress the clutch pedal, fit a bleeder pipe on the nipple and open the bleeder until the fluid stops flowing. Repeat this process until no more bubbles are seen in the bleeder tube. Be careful to not let the reservoir run empty or you will have to repeat the process.

Feb 14, 2011 | Oldsmobile Alero Cars & Trucks

1 Answer

My key remote stop working


The remote battery may have gone flat, or the remote may have come un-synchronised. (Due to a heavy knock or interference from a radio transmitter source. Like someones speed radar detector.)

Replace the battery first, if this does not fix it, consult your dealer on the synchronising process. This is an involved process but easy enough to do yourself at home!

Jan 24, 2011 | BMW 525 Cars & Trucks

2 Answers

How do u bleed the coolant valve do u do it when its hot or cold? just how r u susposed to do it? how do u know when all the air is out of the coolant system?


an easy way to do that is take off the radator cap or over flow cap and start the moter turn your heater to high and put it on defrost once the bubbles stop coming out your done.

Nov 29, 2010 | 1995 Oldsmobile Achieva

1 Answer

1990 toyota 4runner brakes loosing presure How do I change the brake master cylinder


easy shouldnt take more 20 mins ,first remove the old one ,then take that too get the new one so you get the right one ,slide it over the studs then fit the brake pipes starting the threads by hand ,then fit and tighten the two stud retaining nuts .The push the 'plastic resevoir in and fill with fluid .Tighted the brake connectors up with a small pinch ,the assistant pushes brake down whilst you crack each brake pipe in turn ,then let pedal up repeat process a few times till pedal is ahrd ,how difficult it that

Mar 30, 2010 | 1990 Toyota 4Runner

2 Answers

How do you bleed a power steering pump on a 2005 dodge caravan


With the engine running slowly turn the steering wheel from stop to stop several times. Make sure the level stays full. As the air pockets are reduced the level may go down. It may take awhile to get all the air out of the system. If the power steering works it is not a problem.

Feb 25, 2010 | 1999 Dodge Ram 2500 4WD

1 Answer

How hard is it to change a Heater Core on a 1996 Chevy Silverado. My heater is worthless. I've changed the Thermostat with a Stat 195 degree and flushed out the heater core. Still no heat! I've also...


If you flushed out the core and have good flow through it, likely the blend door inside the heater box is not opening. Check the vacuum motors on the box and make sure they are moving as they should.
How difficult the job of removing the core is depends upon your skill level but no one I know likes doing one. Get a chiltons or haynes manual and review the process before attempting the job...if it sounds difficult, don't do it (keep the manual though it's helpful for other stuff)

Jan 30, 2010 | 1996 Chevrolet C1500

1 Answer

Steering


It is an electric assist steering. On very heavy use the motor can become overheated and goes into "safe mode" only partial assist until it cools down. Repeated attempts at parrallel parking have been know to cause this.

Nov 18, 2008 | 2004 Saturn ION

1 Answer

Wiper Motor problen


Most likely this is caused by something binding or water getting inside the motor,either way it is tripping the thermal overload inside the wiper motor.

Oct 22, 2008 | 1995 Buick Park Avenue

Not finding what you are looking for?
2002 Mazda Tribute Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...