Question about Jeep Wrangler

Open Question

1992 yj automatic transmission not shifting gears

1992 yj wrangler driving down the road stops pulling and it want shift into any gear including reverse and 4wd

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

pal03246
  • 705 Answers

SOURCE: Transmission will not shift from

trans problem, internal. you would need to remove the trans pan and look inside of it to see if there is any debriss in it (chunks of metal etc) if you find any metal, you will need another trans and all tranny lines washed out and radiator cooler washed out also. good luck.

Posted on Aug 10, 2008

  • 1 Answer

SOURCE: transmission shifts hard down from highway gear only (D>3rd)

I had the same thing! It was a computer issue. It only cost me about $35.00.

Posted on Dec 29, 2008

wwjdcgh
  • 114 Answers

SOURCE: automatic 3 speed transmission wont shift out of first gear

that is what they consider safe mode for those transmissions, they are a very smart electronic transmission it does that so you dont ruin the trans.
It has detected a problem and you must take it to a tech and have the codes pulled, could be as simple as a sensor or solenoid pack

Posted on Mar 09, 2009

csmock132
  • 4669 Answers

SOURCE: 2004 Jeep Wrangler - Clunking Noise when shifting out of Park

It could be lash in the differential which is normal, but it could also be a loose u-joint in the driveshaft. Check the rear driveshaft u-joints.

Posted on Mar 12, 2009

  • 2 Answers

SOURCE: automatic transmission wont catch into any gear

You sould have been moore frequent on your transmission fluid changes, and you shouldn't have taken it to Jiffy Lube either. Your best bet is to drain and fill the trans fluid run it shift gears. Drain and fill again. Do this 3 times. Yeah the transmission fluid is expensive. on the last drain and fill you want to get a bottle of LUBE GUARD from NAPA or who ever sells it. put the whole 10oz bottle in. Shift Rev, 1, 2, 3, D. Neutral Rev D. If that don't work then you have bad seals.

Posted on May 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

91 jeep wrangler YJ shifting problems


do you mean it wont go into gear ? if so what gears ? it could be the clutch going out , if the pedal is soft or easy to push down than it probably needs a clutch. next time it wont go into gear try pumping the clutch or putting it from 2nd to 1st or what ever gear it has problems with

Dec 18, 2013 | Cars & Trucks

1 Answer

I have a 1994 jeep yj sahara model with a inline 6 4 litre with an automatic transmission. Whenever I shift into drive or any other gear including reverse it makes a rumbling noise and will hesitate to...


No such thing as an easy or inexpensive fix when it comes to a transmission. Since the unit needs to come out and apart in order to do any internal repair, it's rather foolish to do anything except a complete rebuild. Don't forget...Unlike an engine that has many components on the outside, your transmission has virtually everything inside. Have a reputable trans shop do the work. They will check the transmission and the transfer case and make the necessary repair recommendations.

Mar 18, 2011 | 1994 Jeep Wrangler

1 Answer

1994 jeep YJ Automatic transmission does not shift into 3rd all the time. This has happened several times now and seems to straighten itself out - not this time. It used to kick down at 40 mph. Replaced...


For your sake I hoping its a shift solenoid. Yes its in the valve body and there is some transmission surgery involved but its not that pricey. Otherwise it could be the shifter , manual shift valve, 3rd gear linkages etc. This is major tranny surgery. keep me posted.

Apr 01, 2010 | 1994 Jeep Wrangler

2 Answers

My 89 Jeep YJ manual will not go in to reverse while running


Problem is likely either a worn shift fork or bad synchro (both inside the transmission) It's unlikely that you have a clutch problem otherwise the problem would be with first and reverse and shifting other gears would also be difficult.

Sep 01, 2009 | 1989 Jeep Wrangler

3 Answers

Looking for Service Repair Manual Jeep Wrangler YJ


i have a 1988 jeep wrangler 6cyl with 5 speed transmission. I was shifting the jeep and it got stuck in third gear. We opened it up and saw that the linkage is aligned and everything is in place. I dont know what is wrong and what to do next. please help ....

Jul 10, 2009 | 1992 Jeep Wrangler

1 Answer

Jeep 1992 Wrangler won't shift into gear


Not frozen, probably split shifted. Two gears at once.Is this a floor stick or column ahift. Surely not automatic, right? Ley me know and I'll tell you how to undo it

Jul 08, 2009 | 1992 Jeep Wrangler

1 Answer

2004 Jeep Wrangler - Clunking Noise when shifting out of Park


It could be lash in the differential which is normal, but it could also be a loose u-joint in the driveshaft. Check the rear driveshaft u-joints.

Mar 12, 2009 | 2004 Jeep Wrangler

1 Answer

1992 YJ can only shift into 3rd & 4th gear. No Reverse


The same thing happend to one of my wranglers, a 95 yj 4cyl 2.5 liter. The "Aisin AX-5" is the transmission that jeep used on the yj and tj 4cyl and 83 cherokee and up 4cyl, and the "Aisin AX-15"was used on some of the 6cyl models. Both are a "light duty" transmission according to the transmission manufacturer. As everyone knows, A jeep is no light duty vehicle, the shifting slider, a fork like item slides the gears back and forth over the drive and output gears to change the gears. and with heavy use or lack of maintanice they can break, they also can break cause of the cheap casting they used in the tranny. Other problems happen in those trannys too. The only thing is to tear the tranny apart and find out what failed and replace. I did this on the kitchen table ofer a day off. being the up own an early 90s yj, If you are one who doesn't work on their own car, I would find a good garage that is good with jeeps, they are not to expencive to fix, and when they are taken care of, will be a joy to own.
I hope this helps, Jeep ownership is a great thing.

Feb 11, 2009 | 1992 Jeep Wrangler

1 Answer

5th. Gear


Sounds like you may have bent a shift fork or your cluster gear has some missing teeth on it now. I would venture to say that is it a bent shift fork. This will require the transmission be removed to gain access to inspect and repair.

Dec 06, 2008 | 1992 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...