Question about Cars & Trucks

Open Question

How to replace head gasket in ford econovan maxi

Replace head gasket in 2001 econovan

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 236 Answers

SOURCE: What's the process for replacing a head gasket on

If you have to ask this question maybe you should be thinking of not attempting this task and should consult a professional to do the job.

Posted on Jul 08, 2009

  • 59 Answers

SOURCE: Can the Head Gaskets be replaced on a 2001

Yes , but it is very time consuming and if you have never replaced head gaskets before then I would not suggest that this vehicle be your first.

Posted on Aug 12, 2009

  • 12104 Answers

SOURCE: blown head gasket on a 1997 ford taraus a diagram

if u live by a library go to their reference area and look up their car repair manuals photostat the 3 pages if library is neg ask an auto shop if u can copy theirs ,or go 2 a police dept that has the mech shop on grounds they have the books and cd s for the ford line. or last chilton or haynes books

Posted on Sep 25, 2009

  • 75 Answers

SOURCE: TORQUE SPECS /HEAD GASKET/2001 CAVALIER...

for the 2.2L OHV:
(pully 8 4 1 5 9 <-- long bolts @ 63Nm (46ft/lb)
side ) 7 3 2 6 10 <-- short bolts / 10 is the stud @ 58Nm (43ft/lb)

for the 2.4l dohc are as follows:
(pully 9 3 1 5 7
side) 10 6 2 4 8
bolts 1-8 torqued to 65Nm (40ft/lb)
bolts 9-10 torqued to 40Nm (30ft/lb)

then (either engine) give each an additional 90° (¼) turn

it's best to do the tightening in stages, you don't want to go completely tight on the first pass or there will problems and you'll get to do it all over again

Posted on May 24, 2010

  • 161 Answers

SOURCE: Unidentified hose. I have a Ford Econovan, which

2nd hose is for you positive crankcase ventilation(PCV) valve hose....(like a breather hose)

Posted on Mar 20, 2011

Testimonial: "Called the service center and read the Haynes manual, they both say the same thing. Spot on!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 1993 ford econovan maxi engine is missing - what is the likely cause?


missing check the spark plugs is the first thing to look at. check the color of them, if any of them are wet or if one is not the same color as the rest. check these first.

Jun 15, 2017 | Ford Cars & Trucks

1 Answer

I have a 1993 ford Econovan maxi . I have ignition point . What is the gap on the ignition point . Thanks


point gap is .40 to .50 mm ( point 4 to point 5 mm) or .015 to .20"
most point distributors are at the .02 " mark but check and adjust as points to wide will misfire under load or lack power if too close
point gap variations can change ignition timing

Nov 20, 2016 | Ford Cars & Trucks

1 Answer

Sorry i forgot to mention with the lights only working on high beam it's a ford econovan maxi auto 94 do you think its a fuse?


could be the switch stalk if also no dash board lights. Check if voltage going to relay with volt meter or 12V light probe
you can pull out relay and check terminals or jump wire to do relay function to test fuse and globe. A determine if swich is faulty


25785300-5toaxnpomibennkke0mqwyu0-2-0.jpg

Jul 16, 2015 | Ford Cars & Trucks

1 Answer

How much water goes into the cooling system of a ford econovan maxi 1995


depending on which engine you have ,you are looking at 12 to 16 litres when empty

Feb 23, 2015 | Ford Cars & Trucks

2 Answers

Where can I find a step by step guide to replacing the head gasket in a 1991 Ford Econovan?


Try buying a repair manual at any auto parts store or bookstore or find a Youtube video.

Jan 27, 2015 | Ford Cars & Trucks

1 Answer

FORD ECONOVAN MAXi 2.0 Hi, i have a serious creaking and groaning noise from the front nearside when I hit a bump or speed hump could I need a new shock absorber? I dont get the bump I would expect


It could be your shock/strut for sure. It could also be other suspension parts like the control arm or ball joints but I would suspect shocks first. If you arent extremely proficient, I would leave this repair to the pros. It isnt hard but it is incredibly dangerous. To get the old shock off you need to compress the spring with a special tool, and once it is compressed, it is like a bomb waiting to go off and could easily kill you. Take it to a shop and have them confirm the problem then do the repair. It should be around 150 for the part ( or less!) and another 100 for the labor.

Jul 10, 2014 | 1992 Ford Econoline

2 Answers

Valve clearances for a ford econovan 1.8lt, 1990


what are the valve clearance specs for a 1990 ford econovan maxi

Mar 14, 2010 | 1989 Ford Econoline

1 Answer

Where is the clutch fluid reservoir


if it's a hydralic clutch, then it's shared

May 30, 2009 | 1996 Ford Econoline

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...