Question about 2002 Saturn Sl

Open Question

Need the torque sequence for intake manifold on a 2002 Saturn 1.9 SOHC

Torque sequence intake manifold

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 134 Answers

SOURCE: whisling nose from intake manifold.rough idel 2002

sounds like a vacuum leak. Check all of the vacuum hoses.

Posted on Jan 10, 2010

Ad
  • 2 Answers

SOURCE: does the intake manifold from a 2001 Saturn SL2

If you are trying to replace the intake manifold due to a crack in the plastic check out a great option in repairing it.

http://www.youtube.com/watch?v=HK9cXijBnRc

http://cgi.ebay.com/ebaymotors/2000-2002-Saturn-SL2-intake-manifold-part-_W0QQcmdZViewItemQQhashZitem1e5bc99c9dQQitemZ130388958365QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

Posted on Jun 03, 2010

  • 2 Answers

SOURCE: leak from intake manifold

Sorry to hear that. I see this way too often though...
Check out this solution
http://www.youtube.com/watch?v=HK9cXijBnRc

http://cgi.ebay.com/ebaymotors/2000-2002-Saturn-SL2-intake-manifold-part-_W0QQcmdZViewItemQQhashZitem1e5bc99c9dQQitemZ130388958365QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

Posted on Jun 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What do the intake manifold bolts for a 2002 Chevy Malibu with a 3.1L need to be torqued to?


Pretend the picture is lower intake manifold, that is the tightening sequence.
1st step 5 ft lbs
2nd step bolts 1--4 9.6 ft lbs
3rd step bolts 5--8 18 ft lbs
The upper intake manifold use about the same sequence tighten to 18 ft lbs.
If you don't like ft lbs use inch lbs.
If the upper intake manifold is plastic, be careful with that.
intake manifold-glquxvjrls3o0ta25lrevmb0-4-0.jpg

Apr 17, 2017 | Chevrolet Malibu Cars & Trucks

1 Answer

What is the head bolt torque spec on a 94 Saturn sc1 with an 1.9 engine


You will need a torque angle gague to properly torque these bolts. The torque for a SOHC engine is 22lb in correct sequence on the first pass and 37lb in correct sequence on the second pass. You need then install a torque angle gague and in sequence go 90 degrees

May 18, 2015 | Saturn SC1 Cars & Trucks

1 Answer

Torque specs for 2004 saturn intake manifold 3.5


16ft lbs starting at center and working outward, alternating tightening evenly

Mar 14, 2015 | 2004 Saturn VUE

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

Need the torque specs for the upper intake bults on a 2002 chrysler sebring conv. 2.7L


4022caa.jpg

Fig. Intake manifold bolt torque sequence 2.7L engine

Upper intake manifold with a new gasket on the lower intake manifold and torque the bolts, in sequence, to: 105 inch lbs. (12 Nm)

Hope helps (remember to rate this answer). Good job.

Oct 11, 2010 | 2002 Chrysler Sebring

1 Answer

Need to know what to tighten head bolts to on 1992 saturn sl1


DOHC - Tighten all bolts in sequence to 22 ft. lbs. (30 N.m). Then tighten all bolts to 37 ft. lbs. (50 N.m). Repeat sequence, tightening all bolts an additional 1/4 turn (90 degrees).

SOHC - Tighten all bolts in sequence to 22 ft. lbs. (30 N.m). Then tighten all bolts to 33 ft. lbs. (45 N.m). Repeat sequence, tightening all bolts an additional 1/4 turn (90 degrees).

Torque Sequences

Jan 26, 2010 | 1992 Saturn SL1

1 Answer

I need to replace the head gasket on my 2000 saturn sl with 1.9l sohc. its got a bad oil leak on the back of the engine, below the intake manifold somewhere. what is the correct process in taking it apart,...


Normally I would advise exactly how to do a job, but this is one of those tasks that you NEED to buy a haynes manual so you have the correct tightening/torquing sequence, the correct method to set the timing, etc. This can be an involved process, and without the proper illustrations and information, would be homocide to your vehicle's engine to undertake. While you're in there, you'll want to change out the timing chain as well though, FYI.

Oct 22, 2009 | 2000 Saturn SL

1 Answer

Intake manifold torque specs for 2002 Neon SXT


SOHC ENGINE INTAKE MANIFOLD TORQUE IS 105 INCH POUNDS

Sep 28, 2009 | 2002 Dodge Neon

1 Answer

Intake manifold gasket


prev.gif next.gif Intake Manifold REMOVAL & INSTALLATION 1.9L SOHC Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Properly relieve the fuel system pressure.
  3. Drain the coolant system.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Air cleaner fresh air hose
    • Positive Crankcase Ventilation (PCV) valve hose
    • Fuel line from the rail
    • Throttle cable from the throttle body
    • Throttle cable bracket nuts
    • Fuel injector electrical connectors
    • Throttle Position (TP) sensor electrical connectors
    • Idle Air Control (IAC) valve electrical connectors
    • Manifold Absolute Pressure (MAP) sensor electrical connectors
    • Exhaust Gas Recirculation (EGR) valve electrical connectors
    • Heater hose from the intake manifold outlet
  5. Position the wiring harness over the brake master cylinder
  6. Remove or disconnect the following:
    • Intake manifold support bracket bolt
    • Label the vacuum line for proper assembly
    • Drive belt
    • Power steering pump
    • Upper intake manifold bolts
    • Evaporative Emissions (EVAP) canister purge valve solenoid vacuum hose
    • Brake booster vacuum hose
    • Lower intake manifold bolts
    • Intake manifold
    To install:
  7. Thoroughly clean all gasket mating surfaces. Be careful not to damage or score the aluminum surface. If replaced, use Loctite® 290, to seal the new PCV valve inlet tube into the manifold. NOTE: Refer to Section 1 of this manual for the intake manifold torque sequence illustration. The illustration is located after the Torque Specification Chart.
  8. Install or connect the following:
    • New gasket and manifold. Torque the nuts in sequence to 22 ft. lbs. (30 Nm).
    • Power steering pump. Torque the fasteners to 27 ft. lbs. (38 Nm).
    • Drive belt.
    • Heater hose and install the manifold support bracket bolt. Tighten the bolt to 22 ft. lbs. (30 Nm).
    • Lubricate the male ends of the fuel lines with a few drops of clean engine oil, then connect the fuel supply and return lines.
    • Fuel line(s) in the retaining bracket. Torque the mounting screw to 36 inch lbs. (4 Nm).
    • Throttle cable to the throttle body and attach the accelerator cable bracket. Torque the bolts to 22 ft. lbs. (30 Nm).
    • Reposition the wiring harness and connect the wiring and vacuum hoses to their original locations. The harness leads to the TP sensor and EGR solenoid must be routed between the intake manifold runners.
    • Negative battery cable
  9. Fill the coolant system.
  10. Prime the fuel system by cycling the ignition ON for 5 seconds and OFF for 10 seconds a few times without cranking the engine.
  11. Start the engine, check for leaks, and repair if necessary.

Mar 27, 2009 | 2000 Saturn SL

2 Answers

Will not start after it stalls untill about 5-10 minutes


spray carb cleaner on the intake manifold near cylinder 1... common problem is the intake manifold gasket leaks vacuum causing a misfire...the not starting could be due to a faulty crank sensor

Feb 27, 2009 | 2002 Saturn Sl

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...