Question about 2000 Chevrolet Impala

Open Question

High beam on impala 2007 are stuck on high beam

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75817 Answers

SOURCE: the low beams do not work but the high beams do

replace the dimmer switch, that is the most common cause of this,.

Posted on Oct 21, 2009

lindsay836
  • 677 Answers

SOURCE: day time running light and low beams stopped

I would say your light switch is either dirty or bad.
www.rockauto.com

Posted on Feb 04, 2010

c1apton15
  • 3400 Answers

SOURCE: The low beams/day lights on

Visually inspect all your fuses first. If they look good, more than likely the dimmer switch (lever to flip between HI/Low beams is probably bad.

Posted on Mar 07, 2011

  • 14036 Answers

SOURCE: I have a 2005 chev

NO YOU HAVE TO REPLACE HIGH BEAM LIGHT BULBS WITH HIGH BEAM LIGHT BULBS BECAUSE HIGH BEAM LIGHT BULBS AND LOW BEAM LIGHT BULBS TWO DIFFERENT TYPES OF BULBS.WEAR CLEAN LATEX GLOVES HANDLING THE HEADLIGHT BULBS WHICH IS HALOGEN LIGHT BULBS, OIL FROM FINGERS OR HAND WILL CAUSE HALOGEN BULBS TO OVER HEAT BLOW OUT.

Posted on Jul 05, 2011

skychief2001
  • 21873 Answers

SOURCE: How do I replace dimmer switch on 2003 Chevy Impala?

previously answered

Posted on Aug 03, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 impala high beams do not come on, light on dash comes on, replaced bulbs still don't work, checked all fuses, look good


High Beam Headlamp Operation
Battery voltage is applied at all times to the coil and switch sides of the HIGH BEAM PCB Relay located in the underhood fuse block. When the headlamp dimmer switch is placed in the high beam position, the headlamp dimmer switch signal circuit to the BCM is pulled low signaling the headlamp high beam request. In response to this signal, the BCM applies ground through the high beam relay control circuit energizing the high beam relay. With the high beam relay energized, battery voltage is applied through the switch side of the relay, the left and right high beam fuses, and the high beam supply voltage circuits illuminating the high beam headlamps. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) requesting the IPC to illuminate the high beam indicator. Ground for the left headlamp is provided at G101 and the right headlamp at G100.

Nov 23, 2016 | 2010 Chevrolet Impala

1 Answer

Low beams do not turn on


Check the plugs for the bulbs to see if the bulbs are the right ones & that the plugs are OK, making contact & not broke. Use volt tester to see about voltage at plug for both hi & lo beams.

Jan 24, 2014 | 2007 Chevrolet Chevrolet Impala LT

1 Answer

High beam in 2007 Impala pointing down after changing bulb.


Check for proper installation if you you install it properly you should have adjust the head light again by two nut behind the head light one for vertical another for horizontal

Dec 04, 2013 | 2007 Chevrolet Impala

1 Answer

High Beams are stuck on.


it has to be the light switch or linkage to it- if you have linkage.

Feb 09, 2012 | 2000 Chevrolet Impala

1 Answer

I have a 2005 chev impala can i replace my high beams headlights with just low beam lights


NO YOU HAVE TO REPLACE HIGH BEAM LIGHT BULBS WITH HIGH BEAM LIGHT BULBS BECAUSE HIGH BEAM LIGHT BULBS AND LOW BEAM LIGHT BULBS TWO DIFFERENT TYPES OF BULBS.WEAR CLEAN LATEX GLOVES HANDLING THE HEADLIGHT BULBS WHICH IS HALOGEN LIGHT BULBS, OIL FROM FINGERS OR HAND WILL CAUSE HALOGEN BULBS TO OVER HEAT BLOW OUT.

Jul 05, 2011 | 2005 Chevrolet Impala

1 Answer

I own a 2000 Chevrolet Impala. Recently the "highbeam out" indicator light illuminated on the dash message center. Upon inspection the driver side high beam bulb was out and later found that it...


I have a 2003 Chevy Impala 3.4 and I recently got a "highbeam out" message in the message center. I checked the lights and both highbeams are on with the lowbeams. The are stuck on and will not go out. Any suggestions for me to fix this problem? Thank you.

Jim

Jan 05, 2011 | 2000 Chevrolet Impala

1 Answer

Low beams will not turn on.


Try clicking on high beam switch forwards & backwards is stuck or broken in high beam mode. If not able to free up by working forwards & backwards. Will need to replace.

Jun 06, 2010 | 2007 Pontiac Grand Prix GXP Sedan

2 Answers

Bright lights stuck on 2003 Chevy Impala


The bright light dimmer switch will need replacing

Feb 06, 2010 | 2003 Chevrolet Impala

1 Answer

Clicking noise; high beams won't stay on


the hi beam bulb is blown, check your tyres make sure nothing is stuck to them, for the clicking sound, open the hoo, start the engine rev the engine and lislen for the noise.

Jul 30, 2009 | 2000 Chevrolet Impala

Not finding what you are looking for?
2000 Chevrolet Impala Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...