Question about 2006 GMC Envoy

Open Question

Engine cutout will not turnover until igntion is turned off

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't my van start or spark/turnover


You probably need a new battery. There is not enough capacity to turn the starter (which draws a lot of current); low current-drawing accessories (lights, radio, horn) will still work until the battery is flat out dead.

Mar 04, 2016 | 2003 Honda Odyssey

1 Answer

All of a sudden my key fob failed on me. I changed the battery and it still doesnt work. Any suggestions??


FIRST CHECK IGNITION IPC BFC ACC 10 AMP FUSE IF ALL LOOKS GOOD. PUT KEY IN THE IGNITION SWITCH.TURN IGNTION SWITCH TO THE ON POSITION FOR 10 MINUTES UNTIL THE SECURITY LIGHT DISAPPEAR TURN ITSELF OFF,THEN TURN OFF IGNITION SWITCH FOR 5 SECONDS THEN TRY START THE ENGINE.

Jul 20, 2011 | 1999 Oldsmobile Alero

1 Answer

How to reset the service engine light after you have changed the oil?


Hi With the key in the igntion, hold down the odometer reset button. While holding the button down, turn the key to position 1 for 2 sec and the to position 2 untill the service light flashes 3 times. It can be tricky. You may have to do it a few times...hope this helps

Dec 02, 2010 | 2001 Volvo S80

1 Answer

Engine wont turnover until after second or third try


Could be a bad connection at the positive or negative terminals of the battery. I had this problem on my 1997 Cadillac Deville where it would click, or do nothing, and if I toggled the starter through the ignition switch, then it would start on the third or fourth or fifth try.

I thought it was the security system, but it turned out that wire brushing the connectors at the battery (after they were removed) solved the problem beautifully.

Aug 03, 2010 | 2001 Lincoln LS

1 Answer

When cranking engine will not fire until you let


Faulty igntion switch,its mounted on the steering shaft under the dash. you may have to loosen the column so it will drop down to access it .Remove the two bolts that hold it in place

Jan 22, 2010 | 1989 Ford F 150

1 Answer

Igntion switch (the starter immediately start )


I would change the starter out and that will fix your problem

Sep 10, 2009 | 1996 Chevrolet Cavalier

1 Answer

Car won,t start


could be a bad igntion switch. Or a connection from the igntion switch.

Aug 04, 2009 | 2005 Peugeot 405

2 Answers

Volvo S60 2001 warning light, Engine System Service Required comes on. Just had a tune up at 78,000 but not @ Volvo. How do I turn off the light.


  1. Turn the igntion to position I
  2. Press and Hold the Trip Odometer Reset Button
  3. Turn the ignition to position II and hold until the triangle with the ! mark inside flashes (yellow)
  4. Turn ignition off, then back on to confirm reset accepted.

Jul 04, 2009 | 2004 Volvo S60

1 Answer

2005 Toyota Rav4


PUSH AND HOLD RESET ODOMETER BUTTON, TURN IGNITION IN ON POSITION ONLY (DO NOT START ENGINE)UNTIL LIGHT TURNS OFF. TURN IGNTION OFF AND START ENGINE.
BRAKE LIGHT, MAY BE LOW IN FLUID OR LOW BRAKE PADS.

Dec 30, 2008 | 2004 Toyota RAV4

2 Answers

Car won't turnover when key is turned to on position oil light lights but battery light does not come on and engine will not turnover


you sure it is not the entire key mount that is turning as well?
had a friends who had just popped out of place.

Sep 15, 2008 | 1992 Toyota MR2

Not finding what you are looking for?
2006 GMC Envoy Logo

Related Topics:

10 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...