Question about 1999 GMC Sierra

Open Question

Power mirrows on truck stopped working from control switch, hear motor on driver side onlyside move no up or down.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2000 GMC Jimmy SLE driver's power window

I had the same problem...it was the window gear that got stuck when the window was all the way up. (that's the clicking) I took my panel off and banged on the inside of the door with a rubber mallet. The window works again. Since then I make sure when I role the window all the way up to stop that I just barely tap the down button to release the pressure on the gear inside. When your using the hammer...hold the switch in the down mode...ignition on of course.

Posted on Sep 06, 2008

Ad
  • 1 Answer

SOURCE: 2000 GMC Jimmy SLE driver's power window

The same thing happened to my 1999 JMC Jimmy recently. I believe the problem is that your power window motor has most likely gone out or is starting to go out. The motor will need replaced. They are pretty expensive new. I went to a junkyard and got one for around 15 dollars. When mine went bad, I had rolled my window down about three or four inches and it stuck there. I took my door panel off and tapped on the motor while holding up on the window switch and got it to go up after a few minutes. I am replacing my motor today, I'll leave an update here about the outcome when I finish the job. I hope this information helps you.

Posted on Oct 11, 2008

  • 2 Answers

SOURCE: HAVE A 03 GMC SIERRA

I had the same problem in my wife's 2003 Yukon Denali. The power seats and passengers side window wouldn't work. Turned out to be a blown Buss Type fuse in the Underhood Fuse Block. It is the one marked MBEC 1 50amp. Hard to tell if the are blown so look very carefully. Should look like a hoop with two shiny solderlooking bubbles on either side. On my blown fuse, it caught my attention because it looked like the solder was missing and I had to look very closely to see the bottom of the "hoop" was open. They are very hard to remove and must be pulled straight up.
This type of fuse looks like a red square with a clear plastic top showing the fuse link under the plastic. On my vehicle it is on the top row second one from the left.

Posted on Dec 21, 2008

  • 11 Answers

SOURCE: Frying power window switches

I had a similar problem in my 1993 Safari. Problem turned out NOT to be a switch, but a broken wire in the driver side door opening between the door and the frame. I found a cut in the wiring insulation, and it corroded, breaking. This disabled the window control.

Posted on Jun 08, 2009

  • 3911 Answers

SOURCE: My power window on the

it is 8 years old and it is the most used window. it needs a new regulator, buy one at a parts store or on ebay and pay a glass shop to put it in for you.

Posted on Sep 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Controls on driver's side Power seats stopped working. Can not adjust seat at all.


The motors responsible for moving the seats are not being properly powered. The issue could be due to blown fuse, bad relay, bad connections, bad switches, ad infinitum. In short, any part in between the power source (battery) and the motor is suspect.

Get a hold of the wiring schematic for your car, study it, and get to work.

Feb 26, 2016 | 2005 Mercury Grand Marquis

1 Answer

What is wrong when the electric driver seat in a 1995 ford mustang will not move forward or backward but will move up and down.


check switch for proper operation //check motor control for power ,connections and wires are not damaged or disconnected===check seat track for debris or something stuck

Aug 11, 2015 | 1995 Ford Mustang

2 Answers

The driver seat will not go forward


if going backward is working,and foward is not,, easy
,1st determine what is defective-so u know what to replace/repair-2 things only ,[1-switch or 2- motor under d seat]
by presing the backward swicth,, you can hear the sound of the motor running and u can see the seat is going backward...
1-now by pressing the foward switch, and you hear the motor running but not that strong like the rear ..and the seat move an inche /a little and stop,,.then u have a defect weak motor,
2- now by pressing the foward swicth and u dont hear any motor running then the switch is most likely defective
defective switch -repair- spray contact cleaner,remove cover switch,penetrate inside
defective motor-repair-remove motor replace inside carbon,,.chiepest way not to spend to much money..
i suggest even once a month,lubricate all power seat/even not powerseat/,door hinges/.trunk door/.power antenna./ .by spraying lubricating oil,. for maintanace,..you can save a lot..

Oct 14, 2012 | Cars & Trucks

1 Answer

One window will not work


if the master switch dont make window work has to be the window motor. if its the driver side window where master switch is.remove window switch shake wires will working the switch if window try moving switch is bad. if power is at the window switch and using test light to see if power going to window motor if no window motor bad if power going to the power window motor and its trying to move window and you can hear motor working the window regulator causing binding keep window glass from going up or down.

Jul 30, 2011 | 2002 Pontiac Grand Prix

1 Answer

I have a buic lesabre 2000 and the dirver side window stopped working. When I move the window switch I hear a click just like you hear when you move the switch to close and the window is fully close (I...


Try "helping" the window the window to go down by pressing your hand agaist it and pushing it down . If it moves then the motor is not gone. My 02 Century driver window gets slow when it's cold or dirty. Try spraying some ArmorAll into the tracks on the door. This will not only help flush out dirt but lubricate as well

Dec 22, 2010 | 2000 Buick LeSabre

2 Answers

Power seat on driver side only goes forward and back . Tilt and up and down feature has stopped working already checked fuses and rattled the switch around encase it was jammed. No luck....any ideas


The power switch for your seat is a six way switch . It only has one power lead going into it . So , if forward and backward work then you have power to the switch . Would you need to do is try the up and down control while listening closely . If you hear a clicking noise but nothing else when you energize the switch you probably have a bad vertical control motor . If you hear a motor running right after the clicking noise and you probably have a bad control cable which goes between the motor and the vertical gear . If you don't hear anything at all when you activate the switch up and down , I would suspect a bad switch .

Oct 23, 2010 | 2002 Buick LeSabre

1 Answer

I have a 1995 ford windstar. The driver side power window stopped working in the up position. When I depress the switch to lower the window, I hear a clicking noise like a relay coming from under the dash...


The clicking noise doesn't mean anything , relay controls one touch down . Just means relay is probably working ! Take the door panel off an check power to the switch , motor . Watch this videos . Test the electrical circuit The Trainer 24 Power Window Troubleshooting
Automotive Electric Window and Switch Troubleshooting Repair Guide

The motor or the switch or the regulator or maybe be a wiring problem .

Oct 11, 2017 | 1995 Ford Windstar

1 Answer

Electric window 1991 F150 ...351


If the lock is trying to move, like you hear it but nothing really happens, replace the door lock actuator. i believe the windows are on the same fuse. Try removing the interior door trim and tap on the window motor lightly with a small hammer while holding the switch. If the window moves, replace the motor. If not, check for power and ground at the connector. If you have power and ground (which switch when going up then down) then replace the motor. If you dont, repair the circuit.

Aug 04, 2009 | 1991 Ford F150

1 Answer

How to ajust wing mirrows on audi tt


If your tt is equipped w/ power mirrors the switch is on the driver door panel behind the master window switch.  Just twist knob either left or right.  then move knob up or down, or side to side.  Do this with the vehicle on or running.  If switch is in middle it will not do anything.

Mar 22, 2009 | 2000 Audi TT

1 Answer

MY 01 4WD Blazer power side mirrors will not move / not working


You might have a bad switch or a broken cable to the mirrow???? I would lean more toward the bad switch. try cleaning it with contact cleaner or spray it with WD-40.

Jan 02, 2009 | 2001 Chevrolet Blazer

Not finding what you are looking for?
1999 GMC Sierra Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...