Question about 2004 Mitsubishi Galant

Open Question

Good battery, no electricity as if battery was disconnected.

Opened and closed hood and it started up

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you enable a range rover engine when key battery is flat


There is a sequence of left and right turns of the key in the driver's door that will reset your bECM (Rovers brain) if the following have been tried.
1. Replace batteries in remote and 're-sync by depressing lock button on remote while physically turning and locking the door. Don't release button until locked and key removed. Repeat for unlock button.
2. Disconnect negative/earth cable from battery. While disconnected open driver's door, turn ignition to position 2, return to battery leaving driver's door open and reconnect the negative cable. Proceed to ignition. Turn off completely. Close all doors and hood and attempt starting.
Should both of these methods fail, run a search here on fixya for "engine disabled Range Rover P38" This will take you to step by step instructions on resetting the bECM which I opened this post with. It has been covered many times here, including by myself, no reason to post it again.
Good Luck!

Jul 14, 2014 | 2000 Land Rover Range Rover

1 Answer

On my 94 jeep im having an electrical problem, something is killing my battery and i checked the alternator and my starter and i can not find the solution something is killing my battery rapidly please...


START THE VEHICLE, PUT A VOLTMETER ON THE BATTERY. THE VOLTAGE SHOULD READ 13.90 TO 14.80. IF THAT IS OK, THERE MAY BE A BATTERY DRAIN. TURN OFF EVERY SWITCH IN THE CAR.CLOSE ALL THE DOORS. MAKE SURE ALL THE COURTESY LIGHTS ARE GOING OUT. & THE GLOVE COMPARTMENT LIGHT. RAISE THE HOOD. DISABLE ANY UNDER HOOD LIGHTS. DISCONNECT THE NEG. CABLE FROM THE BATTERY. PUT A 12 VOLT TEST LIGHT, ONE END ON THE NEG BATTERY POST & THE OTHER END ON A GOOD GROUND { METAL }. IF THE LIGHT COMES ON THERE IS A BATTERY DRAIN. NO LIGHT , NO DRAIN. IF IT'S ON, ONE AT A TIME PULL THE FUSES OUT OF THE POWER DISTRIBUTION BOX. IF THE LIGHT STAYS LIT, PUT THE FUSE BACK. DO THIS WITH ALL THE FUSES BIG & SMALL. IF THE LIGHT STAYS LIT, DISCONNECT THE ALTERNATOR. THEY CAN CHARGE THE BATTERY WHILE RUNNING, & DRAIN WHEN STOPPED.

Jan 11, 2011 | 1994 Jeep Grand Cherokee

2 Answers

Car alarm won't shut off.


Lot's of things can make it do it but with the drivers door window open. close and lock all the doors. ( said close the doors as in open them and close them back and make sure they close good ) Once all locked up unlock the drivers door with the key twiced once unlocks the door the second time it unlocks all the doors and the thrid time it'll unlock the hatch too. If it does'nt and the alarm is still going off open the hood and close and lock all the doors again. disconnect the battery, ( the alarm will certainly stop then), With the battery disconnected and all the doors closed and locked, put the key in the ingtion and turn it to run ( nothing will happen as the battery is disconnected ) This next part is important. The batterycables should be clean anyway but if their not they need to be clean for the next operation. With them clean put the positive on first and tighten it down now put the negiative onlike you mean it ( don't let it bounce and connect it. The alarm should'nt be going off as the car has the key on. Reach in and start the car ( I did'nt say open the door). with it running it should'nt be alarming either. Turn the key off and remove it them open the door and get in and restart the car itshould be back to normal.. Most of the time one of the door switches said to the computer that it was opened as it was supposed to be locked or it was opened after it was supposed to be locked and you left.

Dec 20, 2010 | 2002 Mercury Villager

1 Answer

How do i disconnect the battery in 2007 hyundai tucson. we will be leaving it for six months.


Use a wrench to remove the negative battery wire at the battery terminal. once this is done,wrap the negative battery terminal in black electrical tape to prevent the terminal from contacting a ground. After the terminal is wrapped in electrical tape, place the terminal aside, and close the hood. (Don't let the terminal stick upwards,and cause hood closure interference).

Apr 17, 2010 | 2007 Hyundai Tucson Limited

1 Answer

How do you change the cooling fan



Electric Engine Fan

Cooling Fan Connectors

Removal & Installation
2.2L& 2.4L Engines
  1. Disconnect the negative battery cable.
  2. Remove the hood close out filler retainers.
  3. Remove the hood close out filler panel.
  4. Remove the upper radiator mount bolts.
  5. Remove the upper two hood latch support bolts.
  6. Remove the two lower hood latch support bolts.
  7. Raise the vehicle.
  8. Remove the cooling fan mounting bolt.
  9. Disconnect the electrical connector from the cooling fan. Remove the cooling fan assembly.

To install:
  1. Install the cooling fan assembly.
  2. Connect the electrical connector to the cooling fan.
  3. Install the cooling fan mounting bolt. Tighten the bolt to 53 inch lbs. (6 Nm).
  4. Lower the vehicle.
  5. Install the lower two hood latch support bolts. Tighten the bolts to 20 ft. lbs. (27 Nm).
  6. Install the two upper hood latch support bolts. Tighten the two upper hood latch support bolts to 80 inch lbs. (9 Nm).
  7. Install the upper radiator mount bolts. Tighten bolts to 89 inch lbs. (10 Nm).
  8. Install the hood close out filler panel.
  9. Install the hood close out filler panel retainers.
Removal & Installation
  1. Disconnect the negative battery cable.
  2. Remove the hood close out filler retainers.
  3. Remove the hood close out filler panel.
    CAUTION Be careful when you handle a sensor. Do not strike or jolt a sensor. Before applying power to a sensor:
    0e518e2.jpg

    Fig. Remove the hood close out filler retainers and the hood close out filler panel
    1. Remove any dirt, grease, etc. from the mounting surface
    2. Position the sensor horizontally on the mounting surface
    3. Point the arrow on the sensor toward the front of the vehicle
    4. Tighten all of the sensor fasteners and sensor bracket fasteners to the specified torque value.
  4. Failure to follow the correct procedure could cause air bag deployment, personal injury, or unnecessary SIR system repairs.
  5. Disable the air bag sensor.
  6. Remove the upper radiator mount bolts.
  7. Remove the upper 2 hood latch support bolts (2).
  8. Remove the 2 lower hood latch support bolts (4).
  9. Raise the vehicle.

    581eb59.jpg
    Fig. Remove the cooling fan mounting bolt
  10. Remove the cooling fan mounting bolt.
  11. Disconnect the electrical connector from the cooling fan.
  12. Remove the cooling fan assembly.
To install:
  1. Install the cooling fan assembly.
  2. Connect the electrical connector to the cooling fan.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  3. Install the cooling fan mounting bolt and tighten the bolt to 53 lb inches (6 Nm).
  4. Lower the vehicle.
  5. Install the lower 2 hood latch support bolts and tighten the bolts) to 20 ft. lbs. (27 Nm).
  6. Install the 2 upper hood latch support bolts and tighten the bolts to 80 lb inches (9 Nm).
  7. Install the upper radiator mount bolts and tighten bolts to 89 lb inches (10 Nm).
  8. Engage the air bag sensor.
  9. Install the hood close out filler panel.
  10. Install the hood close out filler panel retainers.
  11. Connect the negative battery cable.
Hope this help (remember comment and rated this).

Apr 14, 2010 | 2001 Chevrolet Cavalier

2 Answers

2007 Saturn Aura; when trying remote start horn beeps three times but doesn't start. I've replaced battery. Other functions work fine - door locks, trunk opens, alarm arms. Other key fob works fine.


press the lock button on the remote then press the remote start button. if this does not work check remote start status using steering wheel buttons

Jan 03, 2010 | 2007 Saturn Aura XR Sedan

1 Answer

Corolla Ignition(Keys removed)


sounds like it could be a bad ignition switch

Sep 02, 2009 | 2003 Audi TT

1 Answer

I cannot stop my ford streetka alarm from going off


Locate the fuse and or pwer supply, must be direct of the battery, disconnect either.You said the alarm is replaced in the boot, than the power wire to the alarm is located their.Disconnect it, tape off the end and stow.

Jul 23, 2009 | 2005 Ford Focus

1 Answer

Clicking noise under hood of 2001 Chrysler Sebring


Sounds like you have a dead battery. You either need a jump start with jumper box or clean battery terminals and see if that works

Dec 02, 2008 | 2001 Chrysler Sebring

Not finding what you are looking for?
2004 Mitsubishi Galant Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...