Question about 1995 Geo Prizm

1 Answer

Replace rear hose

How to remove water pump

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

This may not help with removal but will get the outer belts off if they get in your way. Also it is good information on major maintainance of timing belt replacement. Replace Timing Belt https://www.youtube.com/watch?v=RqYJHKQ51AU

Posted on Sep 10, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where do I add washer fluid for rear window wiper on a 2000 blazer


Open the hatch and look for the fill cap along the sides .

Oct 23, 2015 | Cars & Trucks

1 Answer

How do I replace the timing belt and water pump on my 1991 sun bird. 2.0 liter engine


Water Pump: Remove timing belt rear protective covers, Remove lower radiator hose from water pump. Remove water pump attaching bolts then the water pump and sealing ring, Clean engine block and water pump sealing surfaces, then apply a 3/32 inch of RTV sealant to sealing surfaces. While RTV sealant is still wet, install water pump. Tighten attaching bolts finger tight. Install lower radiator hose on water pump, then belt rear protective covers. Install timing belt

Jan 18, 2013 | Cars & Trucks

1 Answer

How to replace water pump on 2006 buick lucerne with 4.7l northstar engine


Remove air box & air tube loosen throttle body 2 clamps disconnect Hoses on pump area remove rear cover 4 10mm bolts from rear of pump disconnect two bolts on housing bottom then 4 bolts on center housing two more are on lower rear between eng & tranny the other two are front lower 8 total remove nut fuel line clamp disconnect Wiring move housing out pump area 2-3 inch disconnect tensioner & remove water pump 5 x 10 mm bolts install new pump & reassemble good look 2-3 hours

Apr 23, 2012 | 2006 Buick Lucerne

1 Answer

Wheres the waterpump located on a 98 mazda protoge lx?


Right Side of Engine Block...
The Follwoing instructions will tell you how to remove and replace:
  • Drain the engine coolant into a container that holds at least 6.3 qts. by twisting the plastic drain plug on the rear of the radiator.

  • 2

    Unbolt the air cleaner assembly. The assembly is on the right side of the engine compartment, to the rear of the battery. A single bolt on the right side holds it in place.

  • 3

    Squeeze the tabs on the air intake hose clamp where the hose connects to the engine and pull the hose loose. Remove the air cleaner assembly and hose.

  • 4

    Remove the insulating shroud from the exhaust manifold on the front of the engine. It is held on by four bolts.

  • 5

    Remove the timing belt.

  • 6

    Unbolt the water pump from the right side of the engine block. Unbolt the flange connecting the water line to the pump. Remove the pump.

  • 7

    Replace the pump. Installation is the reverse of removal

  • Feb 25, 2011 | 1999 Mazda Protege

    1 Answer

    I need to replace a thermostat in a 2000 Chevy 2500 6.0 liter pickup


    4.8L, 5.3L and 6.0L Engines To Remove:
    CAUTION
    The thermostat is not serviceable separately. The thermostat housing (water pump inlet) and thermostat must be replaced as an assembly.
    1. Remove the radiator outlet hose. chevy_aval15_02-04_inlet.gif

    2. Remove the bolts from water pump inlet.
    3. Remove the water pump inlet from the water pump.
    To Install:
    1. Install the water pump inlet to the water pump.
    2. Install the water pump inlet bolts.
      • Torque to: 11 ft-lbs. (15 Nm)
    3. Install the radiator outlet hose.
    6.6L Engine To Remove:
    1. Before servicing the vehicle refer to the precautions at the beginning of this section.
    2. Drain the engine coolant.
    3. Remove or disconnect the following:
      • Water outlet 6.6L Thermostat housing removal gm_trk_sil25_02-04_66_therm_hous_rem.gif

      • Bolt for the fuel line bracket
      • Thermostat housing cover bolts
      • Thermostats and seals
    To Install:
    6.6L Thermostats and seals gm_trk_sil25_02-04_66_therm_seal.gif

    1. Install or connect the following:
      • Thermostats and seals to the thermostat housing NOTE: The rear thermostat (D) has 2 vent valves. Install with the vent valves towards the rear of engine.
      • Thermostat housing cover with a NEW gasket
      • Thermostat housing cover bolts and tighten the bolts
        1. Torque to: 15 ft. lbs. (21 Nm)
      • Fuel line bracket bolt and tighten the bolt
        1. Torque to: 15 ft. lbs. (21 Nm)
      • Water outlet
    2. Fill the engine with coolant.
    3. Test drive the vehicle to confirm the repairs.
    8.1L Engine To Remove:
    1. Before servicing the vehicle refer to the precautions at the beginning of this section.
    2. Drain the cooling system.
    3. Remove or disconnect the following:
      • Inlet hose from the water outlet Water outlet and thermostat removal chevy_sub25_02-04_60_thermost_rem.gif

      • Water outlet bolts (B)
      • Water outlet (A)
      • Thermostat (C)
    To Install:
    1. Install or connect the following:
      • Thermostat
      • Water outlet
      • Water outlet bolts and tighten the bolts.
        1. Torque to: 22 ft-lbs (30 Nm)
      • Inlet hose to the water outlet
    2. Fill the cooling system.
    3. Test drive the vehicle to confirm the repairs.
    prev.gif next.gif

    Jan 12, 2011 | 2000 Chevrolet 2500

    1 Answer

    I am seeing water behind the pump on the top of the motor in the v under all the fuel injection / intake is that normal for water pump to leak there if its bad?


    its not normal. the water pump will leak in front, not back. There is a pipe and hose down in the VEE that can leak. If the pipe is bad, you will need to remove the pump to replace it. The intake manifold will need to come off, to replace the pipe/ hose. the hose connects a pipe behind the water pump to a pipe at the rear of the block to a heater hose.

    Dec 12, 2010 | 2000 Ford Expedition

    3 Answers

    Coolant is leaking from hose/pipe under coolant reservoir


    It sounds like the outlet pipe from rear of water pump,which takes the hose from the rear plastic pipe, which is very common problem in Daewoo Leganza/Nubira/Lanos Australian 2.0/2.2 DOHC engines.Either the hose itself, the plastic pipe, or the alloy outlet for the hose on rear of water pump, which is subject to corrosion.You will have to confirm where leak is from, if it is from hose to rear of water pump, you can try re-clamping hose or replacing hose, if it is corrosion of that outlet,the part is available @$40-60 new, but it is a fairly major job because timing cover timing belt and then water pump must be removed...it is a difficult workspace in front of and behind that engine,the manifold and alternator are both in the way , it may be possible to do it in car but you may even be better off removing engine to work on.Good news is that this is a great opportunity to replace T-belt and water pump and pulleys at the same time..Sorry its not that great a news, its not a very easy DIY job, but it is do-able if you have some experience and tools.

    Apr 06, 2010 | 2001 Daewoo Leganza

    1 Answer

    I need to know how i can get to my water pump and what all i need excatly to fix it


    1. Disconnect the negative battery cable.
    2. Drain the coolant into a suitable container.
    3. Disconnect the radiator outlet hose.
    4. Remove the radiator fan motor assembly.
    5. Remove the accessory drive belts.
    6. Remove the timing belt, tensioner and camshaft angle sensor. Refer to the procedure in this section for removal and installation steps.
    7. Remove the left side camshaft pulley(s) and left side rear timing belt cover. Remove the tensioner bracket.
    8. Disconnect the radiator hose and heater hose from the water pump.
    9. Remove the water pump retainer bolts.
    10. Remove the water pump.

    To install:
    1. Clean the gasket mating surfaces thoroughly. Always use new gaskets during installation.
    2. Install the water pump and tighten the bolts, in sequence, to 7-10 ft. lbs. (10-14 Nm). After tightening the bolts once, retighten to the same specification again.
    3. Inspect the radiator hoses for deterioration and replace as necessary. Connect the radiator hose and heater hose to the water pump.
    4. Install the left side rear timing belt cover, left side camshaft pulley(s) and tensioner bracket.
    5. Install the camshaft angle sensor, tensioner and timing belt.
    6. Install the accessory drive belts.
    7. Install the radiator ran motor assembly.
    8. Install the radiator outlet hose.
    9. Fill the system with coolant.
    10. Connect the negative battery cable.
    11. Start the engine and allow it to reach operating temperature.
    12. Check for leaks.





    Jan 20, 2010 | 1992 Subaru Legacy

    2 Answers

    Water pump replacment precedure on 2001 jag stype 3.0


    Hello
    To replace water pump : Raise the car
    1- Drain cooling system. 2- Remove drive belt tensioner clip (if there is one) 3- Remove accessory drivebelt * Rotate the belt tensioner counter clock wise , 3/8 inch square drive bar should do it
    * Remove accessory drive belt
    4- Lower the car 5- Remove the upper shield. 6- Remove the throttle body. 7- Detch the coolant hose from housing assembly. 8- Remove the upper radiator mounting bracket 9- Detach the hose assembly from the water pump and lower hose. 10- Remove the hose assembly * Detach the hose clips
    11- Remove intake manifold support bracket * Detach wiring harness
    * Remove intake manifold support bracket
    12- Detach coolant hose from water pump 13- Remove coolant hose from the water pump to lower housing. 14- Remove water pump
    Installation :
    in reverse order and make sure to use new gaskets and seals

    Jul 07, 2009 | 2001 Jaguar S-Type

    Not finding what you are looking for?
    1995 Geo Prizm Logo

    41 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Geo Experts

    yadayada
    yadayada

    Level 3 Expert

    77169 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22258 Answers

    Mike Gilbreath

    Level 1 Expert

    50 Answers

    Are you a Geo Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...