Question about 1992 Dodge Ram 250

Open Question

How do i remove bolt from 1991 d250 cummings I got the first two but the inside one is hard to get at

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the acceptable max oil clearances on bigends and main bearings on a Cummins 6BT5,9 engine pls. Donr advise AGAIN Buy a Heinz Manual please.


Hi again i found this info on rod & crank clearance 5.9 Cummings .002 to .004 U can always check clearance with plastiguage just to make sure hope this helps GOOD LUCK. only thing i could find was bigend side clearance min .004 max .013in crankshaft end clearance min .004 max.017. ,TRY RINGING CUMMINGS 03 9765 3222 or 03 9360 0800. Good luck....Cummings 6B, 6BT, 6BTA Main Bearing bolts 176 Nm, 130 lb.ft. Con rod 102 Nm, 74 lb.ft. Cylinder head bolts 126 Nm 93 lb.ft ...... Cheers

Nov 19, 2016 | Cars & Trucks

1 Answer

How do I remove the rear speaker in my 1998 Pontiac Grand Prix? Does it involve the cover on the inside of the car? We can't seem to find any way to remove it from the inside of the trunk. It looks like...


Most of the time you get to the rear speakers by opening the trunk and looking up from the trunk that's where the wires connect and the bolts that hold them in and they come out the bottom in the trunk. with all the bolts removed the grill inside the car can be remove as the bolts that hold the speakers in hold the grilles on too

Mar 08, 2011 | 1991 Pontiac Grand Am

1 Answer

Is the starter hard to remove


NO , USE A 10 MM SWIVEL SOCKET FOR THE BOTTOM AND SIDE BOLT ,,USE 10 SOCKET AND 4'' EXTENSION TO REMOVE TOP BOLT USE 8MM SOCKET TO REMOVE SWITCH WIRE AND 13 MM TO REMOVENUT ON BATTERY CABLE TERMINAL OF STARTER

DONT FORGET TO REMOVE THE NEGATIVE BATTERY CABLE FIRST

Aug 08, 2010 | 1991 Ford LTD Crown Victoria

1 Answer

1991 toyota pickup driveaxle removal . 4wd stuck.


there are 6 bolts to remove that hold the drive-axle to the front end housing, you then need to remove the hub and the gears inside, you will then find a snap ring on the other side of the drive-axle that needs to be removed a little moving around and you should be able to remove the axle

Apr 12, 2010 | 1991 Toyota Pickup

1 Answer

What is head torque on a 5.9 cumming 24 valve


step 1. 59 ft. lbs. step 2. 77 ft. lbs. step 3. recheck to 77 ft. lbs. step 4. additional 90 degrees and do each step to all the bolts before going to next step.

Mar 15, 2010 | 2000 Dodge Durango

1 Answer

How do you replace the steering column on a 1991 safari. /


Start by locating the u-joint where the column inside the vehicle ends and protrudes through the fire wall and removing the one retaining bolt. Next remove any knee bolsters/dash parts beneath the column. There should be a u-shaped sleeve fastened by two bolts to the frame cradling the column and holding it in place, remove these bolts. At this point you are about 75% finished removing the column. The only processes remaining would be to diconnect the wiring for the horn and multifunction switch. After which you should have a steering column that is free of the vehicle. Reverse this procedure for installation being careful to note the clocked position of the steering wheel when refastening the u-joint at the bottom of the column.

Oct 24, 2009 | 1991 GMC Safari

1 Answer

Need to replace power steering belt


loosen top mounting bolt and bottom mounting bolt lever in pump to slacken (loosen)belt remove and fit new belt lever out pump while holding tension on pump tighten mounting bolts both are 14mm or 9/16 bolts bottom bolt is hard to see and get to due to not much room can get through wheel arch.
9a5a351.jpg

Jun 14, 2009 | 1991 Toyota Camry

1 Answer

How do you remove the flywheel when replacing the clutch


Take trans out, clutch out, and remove the flywheel bolts.

May 30, 2009 | 2007 Dodge Ram 3500 Quad Cab Laramie

1 Answer

I'm trying to get the battery out of my 2001 Saturn SL1.


if you look at the battery from the top, you will see on the side closest to the fender (away from motor) that there is a bracket that runs along side the battery. It is very hard to notice. You need to take a 10mm socket with a 6" or longer extension, and remove the nut that is on top of it, right at the bottom inside edge of the battery. This may be hard to see, and hard to get to. Unfortunately, that is the only way to remove the battery on that car

Dec 23, 2008 | 1991 Saturn SL1

1 Answer

Need to put a new bed on 1991 pick up how hard is this?


You need to remove the fuel filler tube, disconnet the harnesses that hook to the taillamps, the license plate lamps and any other wiring. Spray penetrating oil around the bed bolts before you remove them. Undo the bolts & have people help you lift the bed off. Not a "hard" job, but a rather heavy type of job. I commonly pull the beds whenever I am changing the fuel tank sending unit.

Aug 13, 2008 | 1991 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...