Question about 1998 Citroen Xantia Break

Open Question

Citroen troubleshooting it is "W" 2000. How do you take off the brake caliper?

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Citroen troubleshooting


there is a switch behind the brake pedal called a brake light switch it is stuck and will need to be replaced it is very simple to replace it just very tight area to get into disconnect wire from switch remove old switch probally has a nut or just slips in reinstall and hook wire all done

May 23, 2013 | 2006 Citroen C3 1.4i

1 Answer

Citroen troubleshooting


Does the brake pedal pulsate? You may just have warped disc brake rotors.

May 01, 2013 | 2001 Citroen Xsara Picasso

1 Answer

Back brakes


into the back brakes. into drums
or on caliper is pads and disc

Jul 05, 2012 | 2001 Citroen Xsara Picasso

1 Answer

How can i compress the caliper piston back of audi a6 2000 2.8l awd what kind of tools i need . Vise grip is not working.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also.
But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!

For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!!

Check brake fluid level and top up if neccessary!!!

Oct 26, 2011 | 2000 Audi A6

1 Answer

Remving caliper pins on 2000 vw jetta and caliper


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Jun 26, 2011 | 2000 Volkswagen Jetta TDI

1 Answer

How to insall front brake pads on a 2000 Ford Focus


caliper bolts are 7 mm Torx head.

SECTION 206-03: Front Disc Brake 2000 Focus Workshop Manual
REMOVAL AND INSTALLATION Brake Pads Removal
syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If brake fluid is spilt on the paintwork, the affected area must be immediately washed down with cold water.
  1. Loosen the wheel nuts.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel.
  1. Detach the brake hose from the support bracket.
  1. Detach the outer brake pad retaining clip.
  1. NOTE: Pull the caliper outwards to release the piston.
    Detach the caliper.
    1. Remove the bolt covers.
    1. Remove the bolts.
  1. syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Suspend the caliper to prevent load being placed on the brake hose.
    Support the brake calipers.
  1. Lift the outer pad retaining clip over the spring retaining lugs.
  1. Remove the outer brake pad.
  1. Remove the inner brake pad.
Installation
  1. syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If the caliper piston is retracted into the housing, brake fluid will be displaced from the master cylinder.
    Fully retract the caliper piston.
  1. syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the brake disc faces are clean before installation.
    Install the inner brake pad.
  1. syy~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the brake disc faces are clean before installation.
    Install the outer brake pad.
  1. Push the outer retaining clip over the spring retaining lugs.
  1. Install the caliper.
    1. Install the bolts.
    1. Install the bolt covers.
  1. Install the brake hose onto the support bracket.
  1. Locate the outer pad retaining clip.
  1. Install the wheels.
  1. Check the fluid level in the brake fluid reservoir.

Jan 18, 2010 | 2000 Ford Focus

1 Answer

2000 Yukon brake caliper


The problem may be with the rubber hose to the caliper. I have seen them come appart inside. You can check it by loosening the hose at the caliper, using a flat screwdriver compress the pad. If it moves free it is the hose. Good Luck.

May 06, 2009 | 2000 GMC Yukon

1 Answer

CLUNKING SOUND IN REAR UPON APPLYING BRAKES 2000 CIRRUS CAR


I would check the brake caliper hinge pins. If the pins are worn, every time you apply the brakes the caliper moves forward against the pins. If the caliper pins and or caliper are worn they will clunk when the brakes are applied.
Check to see if the caliper shifts forward and back.
Let me know.
Regards,

Apr 09, 2009 | 2000 Chrysler Cirrus

1 Answer

Rear brake rotor replacment


206-04: Rear Disc Brake 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  2. Disconnect the brake hose.
  3. Remove bolt.
  4. Disconnect the rear wheel brake hose (2A442).
  5. Remove the copper washers and plug the brake hose.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.

Mar 28, 2009 | 2000 Ford Explorer

1 Answer

How to change front break pads A4 2000 and what type/ make of pads do i need


I have the same car 2000 Audi A4. I recommend you "TRW" brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!! Please Rate my Response! Thanks!

Mar 02, 2009 | 2000 Audi A4

Not finding what you are looking for?
1998 Citroen Xantia Break Logo

Related Topics:

10 people viewed this question

Ask a Question

Usually answered in minutes!

Top Citroen Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14378 Answers

Are you a Citroen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...