Question about 1997 Chevrolet K1500

1 Answer

1997 chevy k1500 control arm

Im trying to replace my ball joints on my truck on the lower ones it ask me if the control arm forged or stamped? who would i figure this out?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 3,433 Answers

I believe if it is stamped the edges of the metal will have almost shap edges, like it hs been cut

Posted on Jun 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am trying to take the lower control arm on the passenger side of a 98 transport. The lower ball joint is being stubborn. I tried ball joint remover tool and not much room to work with and still dont


Lower Control Arm

Print
The lower control arm is a two-piece welded unit with a riveted ball joint. A conventional rubber bushing is used for the rear lower control arm pivot. The front lower control arm bushing is mounted vertically.


REMOVAL AND INSTALLATION

Some special tools are required to perform this operation including, a front hub spindle removal tool and a suitable ball joint separator tool.

WARNING Do not hammer or pry ball joint from knuckle. Failure to use recommended tools may cause damage to the ball joint and seal.
See Figure 1


0900c152801dbd3a.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Exploded view of the control arm-to-frame mounting

  1. Raise the vehicle and suitably support by the frame allowing the control arms to hang free.
  2. Remove the wheel and tire assembly.
  3. Remove the steering gear outer tie rod from the steering knuckle.
  4. Remove the stabilizer shaft link from the control arm.
  5. Remove the front drive axle shaft nut and washer.
  6. Use a suitable front hub spindle removal tool to Push the axle splines back out of the front wheel drive shaft bearing.
  7. Remove the drive axle from the transaxle.

Drive axle joint seal protectors should be used anytime service is performed on or near the drive axles. Failure to observe this could result in joint or seal failure.
  1. Place a modified inner drive joint seal protector on the drive axle joints.
  2. If equipped, remove the ABS wheel speed sensor jumper harness.
  3. Remove and discard the cotter pin, then loosen the nut from the ball stud.
  4. Remove the pinch bolt and the control arm mounting bolts, then remove the control arm from the vehicle.

Apr 20, 2013 | Pontiac Cars & Trucks

2 Answers

What is book time on a lower ball joint on a 2009 for fusion


to replace lower ball joint take at least one hour and half to two hours.some ford vechicle have to replace entire lower control arm with new lower arm ball joints.

Mar 11, 2013 | Cars & Trucks

1 Answer

How to replace ball joints


the lower ball joint is pressed into the lower control arm. You will need a ball joint press to remove and install the ball joint. The other option is to replace the lower control arm.

Some parts store will have presses for loan. You will have to check around and see if any in your area have these. If you can't find one you could always pull the control arm and bring it to a shop or machine shop and have them swap the ball joint.

Its a pretty simple procedure.

1. remove the wheel
2. remove the pinch bolt that secures the knuckle to the ball joint.
3. separate the lower control arm from the knuckle.
4. remove snap ring from the ball joint (if it has one)
5. use a ball joint press to press out the old ball joint.
6. press in the new ball joint.

if you don't have a press than you can remove the lower control arm by following steps 1-3 above. then remove the bolt from the front bushing. Remove the stamped steel skid pan from the sub frame. Remove the rear lower control arm bushing mounting bolts.

If you have any questions I'll be happy to answer them.

Oct 13, 2011 | 1998 Dodge Caravan

1 Answer

Ball joint repair and how do you do it


To perform the following procedure, the lower control arm must be removed from the vehicle. Refer to Removal And Installation for that procedure.

  1. Using a screw driver or other suitable tool, pry the seal boot off of the ball joint assembly
  2. Position receiving cup, Special Tool 6758 to support lower control arm when removing ball joint assembly. Install Remover, Special Tool 6919 on the top of the ball joint assembly.
  3. Using the arbor press, press the ball joint assembly completely out of the lower control arm.

NOTE: When installing ball joint in lower control arm, position the ball joint in control arm so notch in ball joint stud is in the direction shown. This will ease assembly of the ball joint to the steering when installing pinch bolt.

  1. By hand, position ball joint into ball joint bore of lower control arm. Be sure ball joint is not cocked in the bore of the control arm, this will cause the ball joint to bind when being pressed into control arm.

 

  1. Position control arm with installed ball joint, in an arbor press with Receiving Cup, Special Tool 6758 supporting the lower control arm. Then center Installer, Special Tool 6908-4 on the bottom of the ball joint
  2. Carefully align all pieces. Then press the ball joint into the lower control arm until it is completely seated against surface of lower control arm. The ball joint is correctly installed when there is no gap between the ball joint and the lower control arm. Do not apply excessive force against the ball joint or the lower control arm.
  3. Install a NEW seal boot by hand as far as possible on the ball joint. Installation of the seal boot is to be with the shield positioned as shown.

CAUTION: Do not use an arbor press to install the sealing boot on the ball joint. Damage to the sealing boot will occur if excessive pressure is applied to the sealing boot when it is being installed.

  1. Place Installer, Special Tool 6758 over seal boot and squarely align it with bottom edge of seal boot. Apply hand pressure to Special Tool 6758 until seal boot is pressed squarely against top surface of lower control arm.

CAUTION: A replacement ball joint is not pre-lubricated. Properly lubricate the replacement ball joint using Mopar Multi-Mile grease or an equivalent. Lubricate ball joint after seal boot is installed but prior to top of seal boot being pushed down below notch in ball joint stud. Air must vent out of the seal boot at notch when grease is pumped into ball joint, failure to do so will balloon and damage seal boot. Do not over grease the ball joint, this will prevent the seal boot from pushing down on the stud of the ball joint.

CAUTION: After the ball joint is properly greased, clip the end of the grease fleeing off below the hex. The ball joint seal boot is non-purgeable and further greasing is not required and can result in damage to the seal boot.

  1. Reinstall lower control arm on vehicle.

Mar 07, 2011 | 2000 Dodge Caravan

1 Answer

How much of a job is replacing control arm/ball joints on my 98 Windstar?


YOU HAVE TO REPLACE WHOLE LOWER CONTROL ARM IF LOWER BALL JOINTS IS DEFECTIVE BECAUSE LOWER BALL JOINT IS SEALED AND IS A INTEGRAL PART OF THE LOWER CONTROL ARM BOTH IS COMBINED A ONE UNIT.

Feb 21, 2011 | 1998 Ford Windstar

2 Answers

Looking to replace tire rods and lower control arm. What brand should I use? and are the ball joints connected to the control arm?


Hello fes60617: My name is Roger and I will help you. Other then original equipment the most recognized name for replacement parts is MOOG. Has an extremely great warranty.THe lower control arm comes complete with the lower ball joint installed all ready. Make sure to have the alignment on the van reset. This will change dramatically when you replace the parts. Should you need further help please just ask. Please rate the answer. Thank You for using Fix YA. Roger

Jan 31, 2011 | 2001 Ford Windstar

1 Answer

How to replace s500 control arms How much do they cost, and it there an additional ball joint. My mechanic tacked this on. I thing the control arm and ball joing is one unit.


To replace the lower control are you need to unbolt it from the subframe, airmatic strut, sway bar link and from the lower ball joint. The lower ball joint is separate from the lower control arm. The ball joint actually gets pressed into the steering knuckle. Then the lower control arm sits on top of the ball joint and gets bolted down. The lower control arms list price are about $330 each and the ball joints are around $78 each for oem mercedes parts. The total labor for both to be replaced is somewhere between 6-8 flag hours. The thrust arms are also part of the front suspension and those arms are one piece that have a ball joint as part of the arm. The lower control arm usually doesn't need to be replaced unless its damaged since the control arm bushings are available separately and are around $73 each side for the kit.

Oct 07, 2010 | 2003 Mercedes-Benz S-Class

1 Answer

1992 lower ball joint replacement


THE LOWER BALL JOINTS ARE A VERY TIGHT PRESS FIT INTO THE ARM, YOU NEED TO BUY A BALL JOINT PRESS KIT TO REMOVE THEM, BUT BASED ON MY PAST EXPERIENCE IT IS BEST TO JUST REMOVE THE LOWER CONTROL ARM AND HAVE A MACHINE SHOP PRESS THEM OUT AND THE NEW ONES IN, IT IS VERY EASY TO DISTORT AND RUIN THE CONTROL ARM DOING AN "ON THE CAR REPLACEMENT", THE BALL JOINT PRESS KIT RUNS ABOUT $50-$200 DEPENDING ON THE MAKER AND THE QUALITY, TRY WWW.HARBORFRIEGHT.COM TOOLS FOR AN ENTRY LEVEL KIT.

Jul 06, 2009 | 1992 Lincoln Town Car

1 Answer

Can you replace the lower ball joints in the control arms


You can replace them seperately,but they need pressed out and in. Other methods of removing and installing likely will damage control arm.

Apr 23, 2009 | 1998 Ford Expedition

1 Answer

I want to replace lower ball joint on my nissan altima 2001


Hi,
Remove the castle nut on top of the ball joint that secures the ball joint to the spindle. separate ball joint/lower control arm from spindle.Remove lower control arm bolt attatching control arm to subframe/engine cradle. Remove control arm. Replacement is recersal of the removal. Nissan/Infinity ball joints can not be pressed out or in. They are replaced with the whole new lower control arm as one (On most Nissan/ Infinity vehicles, although some exeptions apply. Hope this helps.
Daniel G.

Oct 06, 2008 | 2001 Nissan Altima

Not finding what you are looking for?
1997 Chevrolet K1500 Logo

403 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...