Question about Ford Laser

Open Question

Need wiring diagram for fuel pump relay on ford kf laser

Wiring problem on fuel pump relay

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: i need a 2002 ford ranger fuse box diagram and afuel pump relay switch diagram

Hi

go to www.motorcraftservice.com then click on the owner guide and put in your truck information
then choose the 1st owner manual printing and should be between page # 184 to 200.

Good luck and I hope this will awnser your question.

Posted on Nov 08, 2008

  • 491 Answers

SOURCE: 1988 ford f150 fuel pump relay location

inner driver side fender well along with the eec relay

Posted on Feb 02, 2009

  • 1 Answer

SOURCE: Fuel Pump Relay for 1993 Ford Tempo

it is in the trunk on the left hand side, pull away the trunk carpet on left side and you will see a hole with a top and bottom screw remove the screws and pull the relay out threw the hole, then disconect the wiring connector When you plug the relay back in turn on key you should here the pump run for a few seconds if it does not then replace the relay ,or the pump.

Posted on Apr 27, 2009

  • 1 Answer

SOURCE: no power to fuel pump or fuel pump wiring harness...

try the electrical ignition switch on the steering wheel colum

Posted on Aug 25, 2009

  • 652 Answers

SOURCE: need wiring diagram for ford explorer fuel pump

Hope this heb7e924f.jpglps

Posted on Apr 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel pump wiring diagram 2000 ford explorer


Found this wiring diagram, hope it helps. Note the inertia switch and fuel pump relay.
explorer fuel pump-ioxn1op2wvzql5cgynmtml03-5-0.jpg

Mar 11, 2017 | Ford Cars & Trucks

1 Answer

Hotwiring fuel pump on 2001 ford expd which color is hot wire?


Why do you want to hot wire the fuel pump ? Did you check the fuel pump relay ? How about the inertia fuel cut off switch ? Do you know what inertia fuel cut off switch is ? Go to http://bbbind.com/free_tsb.html free wiring diagrams ! Also suggest you watch this video on fuel pump electrical circuits ! how they work an how to test . Fuel Pump Electrical Circuits Description and Operation Watch for ford's , well , watch it all you mite learn something !

Jul 30, 2016 | Ford Cars & Trucks

1 Answer

1993 ford F250 dual tanks replaced back fuel pump. Have checked reset,relays and fuses. Still has no power to the pumps. What else could it be?


You need to look at a wiring diagram an check voltage an ground for that circuit . If you don't know how to do basic electrical testing your best bet is take your vehicle to a qualified repair shop that does . You replaced a fuel pump that didn't need replacing . Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts

You can find a wiring diagram at
http://bbbind.com/free_tsb.html

Jun 12, 2016 | Ford Cars & Trucks

1 Answer

1986 ford f150 tested fuel pump with cables,pump runs no power when hooked to wires going to tank, is it relay


THIS IS ALL ON MEMORY SO GET YOURSELF A WIRING DIAGRAM FOR THAT TRUCK!!!
If you have one you should install an inline fuel pressure gauge to verify that you are indeed not getting fuel pressure first. Assuming you have no fuel pressure, it could be one of a few things.
check all of you fuses
if ok, check fuel pump relay for activation during engine cranking. I believe in that vintage Ford, the oil pressure switch is responsible for activating the relay. So with a test light backprobe the activation wire at the relay. if you get activation power at the relay, and no relay activation, then yes it is the relay, but if you get nothing, then it will be the oil pressure switch. If you get activation to relay and still no pump activation then you might have a break in the wiring OR the fuel pump has short brushes.

I know thats alot to take in but hey thats what a diy forum is for right? Good luck!!!

Dec 28, 2012 | 1986 Ford F150 SuperCab

1 Answer

Elecric fuel pump wiring diagram needed - fuel pump not working...new relay didn't help


turn the ignition key to the ON position without starting the engine up. You should hear the fuel pump run for 5 seconds. If not heard replace the oil pressure sensor which is linked to the same circuit.When oil pressure is acheived the fuel pump relay takes over to run the pump

Jun 11, 2011 | 1989 Ford F 150

1 Answer

1995 ford f150 - truck ran fine.turned on turn signal and started around turn and truck shut off and will not start.it has no fuel pressure in fuel rail and no diagrams for fuel pump relay's...


You can get a 1996 manual at the link below. That may be close enough. It shows 5 relays in the box under the hood. Relay 2 is for the fuel pump. Your wiring diagrams are at the second link below, and the particular diagram for the relay is at the third link.

http://www.fleet.ford.com/partsandservice/owner-manuals
http://www.bbbind.com/free_tsb.html

http://www.revbase.com/BBBMotor/Wd/DownloadPdf?id=2020

Aug 07, 2017 | 1995 Ford F150 Styleside Regular Cab

2 Answers

I replace the fuel pump on my 1992 ford bronco and still doesnt supply fuel is there a relay i dont know of


Are you getting battery power and ground at the fuel pump connector? (This should have been checked BEFORE replacing the pump)

Other things to check:
1. Fuel Pump relay in the Engine Compartment Fuse Block
2. The relay is powered (Secondary -or- "fuel pump side") by Fuse 0 in the Engine Compartment Fuse Block.
3. The relay Primary -or- "control" side is powered by Pin 37 RED wire at the PCM
4. The relay Primary control (or ground circuit) is operated by Pin 22 LIGHT BLUE/ORANGE wire at the PCM
5. The Inertia Fuel Shut-off Switch located between the fuel pump relay and the fuel pump may need to be reset. The switch is located behind the right kick panel. The DARK GREEN/YELLOW wire at the switch is the feed from the fuel pump relay. The other wire goes to the fuel pump. Some units have the DARK GREEN/YELLOW wire going in and the wire going out can also be DARK GREEN/YELLOW, or PINK, or ORANGE - the wiring diagram for your vehicle does not specify the color of the wire that actually goes to the fuel pump itself.)
6. If none of the above produce any results, make sure that your ground wire at the fuel pump has good continuity to ground. It usually screws to the left frame rail near the fuel tank.

Any of these components (including the PCM) or their connecting wires could be the cause of your problem.

May 15, 2011 | 1992 Ford Bronco

2 Answers

99 Ford Windstar. Not getting any power to the fuel pump


first check the fuse if it is good then check for power at the relay

Jan 10, 2010 | 1999 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...