Question about 2004 Buick Rainier

Open Question

Rear shock torque - 2004 Buick Rainier

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Tahoe rear suspension torque specifications


A few good hits with the 1/2" impact should do.

Sep 29, 2015 | 2002 Chevrolet Tahoe

1 Answer

What are the Front and Rear Strut lower two bolt nut torquing requirements? Are they really 221 ft-lbs?


Front lower strut/ shock mount 155 ft/lbs.
Rear lower strut/ shock mount 133 ft/lbs.

Jun 03, 2015 | 2009 Toyota Camry LE

1 Answer

Shock absorber torque specs for 2000 jeep grand cherokee laredo


specs, rear?
we just set them to 35ft./lbs
if frisky you can read the fSM for that.
or use google, ever use google,.????? amazing my 1st hit
here ill type it for you....... omg

http://www.jeepforum.com/forum/f67/rear-shock-bolt-torque-954751/#post9025080

Dec 18, 2013 | 2003 Jeep Grand Cherokee

1 Answer

Looking for torque spec for bolts holding the rear shocks on the rear of a 2006 Dodge Sprinter 3500


Hello acadiamaine,

If the shock absorber bolt to the axle is a 14mmX1.5 it should be torqued to 110 Nm if it is a 12mmX1.5 bolt torque it to 70 Nm.

The bolt to the frame side should be torqued to 140 Nm if the axle bolt is 14mmX1.5 and 80 Nm if the axle bolt is 12mmX1.5.

I hope this helps.

Regards,

Jerry

Sep 15, 2011 | Dodge Sprinter Cars & Trucks

1 Answer

How to replace the rear shocks on a 1998 nissan maxima


REMOVE REAR SEAT AND PACKAGE SHELF TO GAIN ACCESS TO THE UPPER SHOCK ATTACHING NUTS.REMOVE UPPER ATTACHING NUTS. RAISE VECHICLE REMOVE REAR WHEEL AND SUPPORT THE LOWER CONTROL ARM WITH A JACK REMOVE LOWER SHOCK ABSORBER MOUNTING BOLT. REMOVE SHOCK ABSORBER ASSEMBLY FROM THE VECHICLE. COMPRESS THE COIL SPRING WITH THE PROPER SPRING COMPRESSOR TOOL. REMOVE CENTER RETAINING NUT HOLDING THE UPPER MOUNTING INSULATOR. SLOWLY DECOMPRESS THE COIL SPRING.REMOVE THE MOUNTING INSULATOR AND THE COIL SPRING. REMOVE THE COIL SPRING. TO INSTALL COMPRESSED COIL SPRING ONTO THE STRUT ASSEMBLY. BE SURE TO THE END OF THE SPRING IS IN THE NOTCH ON THE LOWER SEAT.INSTALL UPPER MOUNTING INSULATOR. YOU WILL NEW LOCKNUT FOR THE CENTER RETAINING NUT OF THE COIL SPRING. CENTER RETAINING NUT AND TORQUE THE NUT TO 13 TO 17 FT LBS. SLOWLY REMOVE THE SPRING COMPRESSOR TOOL. INSTALL SHOCK ABSORBER ASSEMBLY IN THE VECHICLE AND INSTALL THE MOUNTING FASTERNERS AND TORQUE LOWER MOUNTING BOLTS TO 72 - 87 FT LBS. INSTALL WHEEL.LOWER VECHICLE. WARNING COIL SPRING UNDER EXTREME LOADS WHEN COMPRESSED.BESURE TO PROPERLY ALIGN THE SPRING WITH THE COMPRESSING TOOL TO PREVENT PERSONAL INJURY FROM THE SPRING RELEASING UNEXPECTEDLY.

Feb 02, 2011 | 1998 Nissan Maxima

1 Answer

How to disassemble the rear end in a 2000 gmc yukon and how to remove axles


Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Loosen the lug nuts on the wheel and tire assemblies but do not remove the lug nuts
  3. Raise and support the vehicle
  4. Remove or disconnect the following:
    • Wheel and tire assemblies
    • Axle lubricant into a suitable container
    • Rear driveshaft
    • Parking brake cable
    • Brake calipers
    • Shock absorbers from the axle brackets
    • Vent hose from the rear axle vent fitting
    • Nuts and the washers from the U-bolts
    • U-bolts, spring plates and spacers from the axle assembly
  5. Lower the axle assembly from the vehicle
To Install:
  1. Place the rear axle assembly under the vehicle
  2. Align the rear axle assembly with the springs then connect the spacers, spring plates and the U-bolts to the rear axle
  3. Raise the rear axle assembly into position
  4. Install or connect the following:
    • Washers and nuts to the U-bolts; Torque to: 59 lb-ft. (80 Nm) then, Torque to: 89 lb-ft. (120 Nm)
    • Vent hose to the rear axle vent fitting
    • Shock absorbers to the rear axle
    • Brake calipers (See: Brake Caliper)
    • Parking brake cable (See: Parking Brake Cable)
    • Rear driveshaft (See: Rear Driveshaft)
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  5. Fill the rear axle with lubricant
  6. Bleed the brake system (See: Brake Bleeding)
  7. Install the wheel and tire assemblies
  8. Lower the vehicle to the ground
  9. Torque lug nuts as follows:
    • Single Wheel: Torque to: 140 lb-ft. (190 Nm)
    • Dual Wheel: Torque to: 175 lb-ft. (240 Nm)
  10. Road test the vehicle to check performance
prev.gif next.gif

Aug 03, 2010 | 2000 GMC Yukon XL

1 Answer

Need new struts on rear, Would like to replace with air shocks. Any suggestions on how I would do this?


Shock Absorber -The rear already has air shocks on the 1999 Cadillac Deville: REMOVAL & INSTALLATION Rear
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Rear wheel Fig. 1: Exploded view of the rear shock absorber mounting 9300vg06.gif

    • Negative battery cable
    • Shock absorber electrical connector from the rear suspension support, If equipped
  3. Support the lower control arm with a jack to relieve the tension on the shock absorber.
  4. Remove or disconnect the following:
    • Lower shock absorber mounting bolt and nut
    • Upper mounting nut, retainer, and insulator
    • Shock absorber compress by hand and remove through the upper control arm
    To install:
  5. Position the top of the shock absorber with the insulator attached into the suspension support.
  6. Install or connect the following:
    • Upper shock insulator, retainer and nut. Torque the nut to 55 ft. lbs. (74 Nm).
    • Shock absorber lower mounting nut/bolt. Torque the nut to 75 ft. lbs. (102 Nm).
    • Shock absorber electrical connector to the rear suspension support, if equipped
    • Rear wheel
    • Negative battery cable
prev.gif next.gif

Jul 29, 2010 | 1999 Cadillac DeVille

1 Answer

Replace broken rear coil spring on pontiac montana


PLEASE DON'T FORGET TO RATE!!!

Removal & Installation

Remove or disconnect the following:
  • Brake hose bracket screw from the control arm
  • Shock absorber lower bolt while using a utility stand to support the rear axle
  • Tie rod from the rear axle
  • Spring and insulators after lowering the rear axle

7fc1aec.gif
Exploded view of the coil spring assembly


To install:
  1. Install or connect the following:
    • Insulators and springs on the rear axle with the paint stripe is facing rearward
    • Rear axle tie rod after raising the rear axle into its proper position. Torque the nut to 92 ft. lbs. (125 Nm).
    • Shock absorbers to the rear axle. Torque the upper and lower nuts to 63 ft. lbs. (85 Nm).
    • Brake hose bracket to the control arm. Torque the bolt to 33 ft. lbs. (44 Nm).
  2. Remove the axle supports.

Oct 17, 2009 | 2000 Pontiac Montana

1 Answer

I need the rear shock torque specs for a 2007 sport trac


Torque Specifications Description Nm lb-ft lb-in Brake caliper bolt 32 24 — Brake disc shield bolt 8 — 71 Fuel tank filler pipe bracket bolt 15 11 — Fuel tank filler pipe hose clamps 3 — 27 Halfshaft nut and washer 275 203 — Lower arm inboard bolt 250 185 — Lower arm outboard bolt 275 203 — Parking brake cable bracket bolt 10 — 89 Shock absorber lower bolt 275 203 — Shock absorber rod nut 65 48 — Shock absorber upper mount nut 30 22 — Stabilizer bar bracket nut 48 35 — Stabilizer bar link nut and grommet 30 22 — Toe link cam adjuster nut 275 203 — Toe link outboard bolt 325 240 — Trailing arm bolt 300 222 — Upper arm outboard bolt 225 166 — Upper arm inboard nut 250 185 — Wheel speed sensor bolt 8 — 71 Wheel knuckle bolt 275 203 —

Mar 30, 2009 | 2007 Ford Sport Trac Limited

Not finding what you are looking for?
2004 Buick Rainier Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...