Question about 1996 Volkswagen Cabrio

2 Answers

Eingen vibrate when pulling away till about 2000rpm

I have had new engin mounts replaced on my vw jetta3 by speedy now when i pull away the car vibrates.

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 253 Answers

It sounds to me that you have a torsional vibration. when the mounts were replaced the engine was not centered and somewhere metal is touching the frame. Re-Aline the mounts and road test.

Posted on Feb 17, 2013

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Volkswagen Master
  • 3,433 Answers

POSSIBLY A SPARK PLUG WIRE WAS DIS CONNECTED.

Posted on Jun 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i fix the vibrating noise/feeling especially on the left hand side of the nissan bluebird sylphy?


If the noise gets worse making a right turn, then goes away or close on a left turn. It is a wheel bearing. If it an engine mount. Put a jack under it and lift the engine slightly. If the vibration goes away. I suggest you replace all the other mounts.

May 14, 2016 | Nissan Cars & Trucks

1 Answer

2001 Suzuki Esteem wagon develops a loud vibrating noise when the engine is under load. When pulling up to a stop light, the noise is quite loud even at full stop. Switching from drive to neutral stops the...


It sounds as if the mounts or trans/engine mounting hardware is becoming loose...Unless the engine is out of timing and running rough ....Take it to the tech that repaired the mounts and have them inspect their work.......

Dec 13, 2014 | Cars & Trucks

3 Answers

Why does a 2006 Ford Fusion have a strong vibration when stopped and in Drive?


If there are no check engine lights could be a bad motor mount or two. Would have them checked. Try putting car in neutral and see if vibration disapates a little.

Aug 23, 2012 | 2006 Ford Fusion

1 Answer

2007itsubishi spyder eclipse with vibration at idle when stopped at lights accelerate and vibration goes away


Hi Kris, The vibration could be from a number of places, more so as the engine has been replaced. I suggest you check the exhaust mountings, the exhaust covers, and exhaust mounts. Regards John

Aug 18, 2012 | Mitsubishi Eclipse Spyder Cars & Trucks

1 Answer

My car vibrates when I am in reverse where do I start?


Either engine mounts or oil on clutch plate. If try to pull away in first with handbrake full on and car stalls, not oil on plate....:D

Sep 28, 2009 | Volkswagen Passat Cars & Trucks

8 Answers

This is a 1974 charger,360 ,4bbl,auto-problem is engine vibration. engine is running good, butvibrates almost like a miss,noticeable even in neutral, but more noticeable as the rpms are higher.when...


Hi,

vibrations over 55 mph are usually balance related (tire balance, drive shaft balance, motors)

vibrations at lower speeds are usually mechanical (bent rims, out of round tires, bad tie rods)
Therefore the suggestion for checking the harmonic balancer is perfect in your case.

Thanks

May 09, 2009 | Dodge Charger Cars & Trucks

1 Answer

Where is the blower located in a VW 1996 Polo - stopped working!


the blower is in a vertical position under the passenger side dash far left. just twist to unluck and pull out

Jan 03, 2009 | 2001 Volkswagen Golf

1 Answer

2000 Camry gearbox vibration


hi, ok I will suggest to check all the cambelt tensioners, the bearings on them are worn

Jun 10, 2008 | 1997 Toyota Camry

Not finding what you are looking for?
1996 Volkswagen Cabrio Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...