Question about Cars & Trucks

1 Answer

I have a 96 ef2 futura falcon the brake light do not cone on and the is no switch on brake pedal anyone got an idea where it is ?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 69 Answers

Could be by the brake booster and reacting to brake fluid pressure.

Posted on Apr 19, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: brake pedal switch

Yes. Because the switch use a individual wire to the 3rd light.
To separete from the rear. because the rear lights, use the same bulb to signal and brake light.

Posted on Jul 24, 2008

  • 188 Answers

SOURCE: 2001 dodge ram 1500 brake lights

I would guess the brake fuse ( this does not use the same fuse as the tail lights/blinkers) or the ground for the brake light bulb.

Posted on Aug 22, 2008

  • 1 Answer

SOURCE: Brake Light

The hole in the pedal arm is for the cruise control. There is a plastic plug that needs to be in place to turn off the brake lights. They should be available at any dealer - there is also one for the clutch pedal arm in manual trans. These are required for the cruise as well as to turn off the brake lights. I bet that several will now be able to have their cruise back.

Posted on Nov 09, 2008

  • 840 Answers

SOURCE: 2001 ford ranger no brake lights

check fuses under the dash and in the engine compartment/ Please rate my response thank you very much

Posted on Feb 01, 2009

  • 9 Answers

SOURCE: No brake lights on 96 yukon

The brake fuse #1 is located inside the truck below the steering column. I am assuming you have verified there is 12v power at the fuse & thru the brake lamp switch (orange wire power in & white wire power out, when pedal depressed) at all times. After the brake lamp switch , power goes (white wire) to the Turn signal/hazard lamp switch & out (dark green wire-rt brake lamp & yellow left brake lamp)

Posted on Feb 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 Ford Windstar Brake stopped working out of no where. I replaced the bulbs and yet the brake lights still won't work. Any ideas?


96. Could be the brake switch died. Do you have a high mount brake light in the back? If so, does it work? If it doesn't it is the brake switch. mounted by the brake pedal. If it does, then it is the turn signal switch that needs replaced.

Sep 04, 2015 | Ford Cars & Trucks

1 Answer

I can start my ford e250 van but it's stuck in park. If I barely turn key on I can get it to shift in neutral and start it and drive it but no brake lights. Anyone have any idea what's going on?


Replace the brake switch. Under the dash, touching the brake pedal arm. Another possibility is the ignition switch by how you described it. Press the brake pedal and have some check the brake lights. If they come on, I would go after the ignition switch. No lights brake switch.

May 06, 2015 | Ford Cars & Trucks

1 Answer

Changing a brake light switch on a 1998 ford falcon


look under the steering wheel, and follow the brake pedal,there should be a switch close close to the firewall

Aug 02, 2014 | 1997 Ford Falcon

1 Answer

Why wont the brake lights shine when pressing the brake pedal but the tail lights are working on the same bulb


test the brake light switch located at the brake pedal, disconect the switch & bridge the wires, turn ignition on if you have lights its a faulty switch (very common on ford falcons) if not check you have power at that plug, if power check the globes cause you could have blown globes as they are twin filiment globes (1 globe but 2 lights tail & brake) & the brake filiments might be blown.

Jun 26, 2012 | Ford Expedition Cars & Trucks

1 Answer

96 plymouth grand voyager is stuck on park what does that mean?


Your problem might be with the brake light switch. This switch is under the brake pedal, and when the pedal is pressed, it lets you shift your van out of park. This switch also activates the brake lights when you press the brake pedal. Try checking if your brake lights work. These switches are inexpensive, and very easy to replace.
Matt

Jun 15, 2011 | 1996 Plymouth Grand Voyager

1 Answer

My brake lights won't work in my AU Ford Falcon


On vehicles that use a common bulb for signal and brake lights the brake light circuit runs through the signal switch. A problem in the signal switch can cause the brake lights not to function. Also check your Emergency flasher switch. Hope this helps.

Apr 11, 2010 | Ford F Cars & Trucks

1 Answer

Brake Lights


brake light switch behind the brake pedal, well just above the brake pedal is bad or loose/ replace it. problem solved

Aug 25, 2008 | 2006 Pontiac G6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...