Question about 2005 Mazda 6

1 Answer

Battery changed on mazda 6 and both driver side window dont work

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 264 Answers

Hi I'm Peter, It would be highly unlikely that changing out a battery would cause the window motor to fail. A couple of things come to mind, one there is a possibility for some reason you may have a fuse blown or a relay go bad these can be checked in the fuse box under the hood and possibly the fuse panel inside the car usually somewhere around the drivers left leg. Another possibility I have seen is where someone put a cheaper battery with not enough amperage to handle the load of the window motor but they are normally slower then not stopped and also if the other window motors are working the weaker battery most likely isn't the problem. Worse comes to worse and the fuse and\or relay you can remove the switch on the door and check or voltage at the switch and if you do the check continuity through the switch t make sure it is operating. The way you worded your query it seems like the driver and the passenger on the driver side windows or just the driver window and all the rest are working. I would also like to know if there are any other electrical things not working now dome lights, radio, das lights, etc.

Posted on Apr 19, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: new battery in 06 mazda 6

1. Turn ignition switch to "on" position.
2. Open passenger window completely from passenger side window switch.
3. Close passenger window completely from passenger side window switch, and hold switch for an additional 2 seconds.
4. Turn ignition back to "lock" position.

That's it. Works like a champ. And here you thought it was more than just a battery dying....I did.

Posted on Jun 10, 2009

  • 583 Answers

SOURCE: Driver's side power window will not work

Remove door panel to check wiring to switch and motor
See if motor is getting power through the switch - if so motor is bad
If no power to motor check operation of switch - jump wires to test
if window works bad switch

thanks.

Posted on Jul 08, 2009

  • 31 Answers

SOURCE: can't control passenger window in mazda 6

Passenger window lost programing. To reprogram, turn the key on, go to the passenger side and with the passemger switch run the window all the way down and hold switch in down position for 2 seconds, then run all the way up and hold in up position for 2 seconds, then repeat again within 5 seconds. Should work from drivers side master switch now.

Posted on Sep 17, 2009

  • 1 Answer

SOURCE: I changed the battery of my mazda 6 and I tried to

Here is the proper procedure,

POWER WINDOW INITIALIZATION PROCEDURE
1. Turn ignition to ON position.
2. From driver's seat ensure window lockout switch is NOT depressed.
3. Press window switch down to fully open door window.
4. Pull window switch up to fully close door window; hold switch up for two (2) seconds; release switch.
5. Move to front passenger seat and repeat Steps 3 - 4 on passenger window switch.
6. Mazdaspeed6 Only: Move to rear seat and repeat Steps 3 - 4 at left and right rear seat window switches.
7. Verify proper window operation using each door switch.

This was taken from a service bulletin.

Posted on Mar 02, 2010

  • 1 Answer

SOURCE: Passenger window won't work using the driver side control switch

Open the window with the local button and keep the button pressed for 3 seconds after it has fully opened. Then close the window and keep the button pressed for 3 seconds after it has fully closed. This calibrates the position of the window which it lost when you changed the battery. Good luck

Posted on Apr 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The battery got disconected now windows dont work tried re program checked fuses nothing now what


You need to do a window reset. Its in your owners manual

This is a quote from the workshop manual

Note
? A driver side window will not fully close automatically under following the conditions:
? The battery has been disconnected during vehicle maintenance or for other reasons.
? The power window main switch connector, or driver-side power window motor connector has been
disconnected.
? Carry out the following procedure to resume operation:
1. Turn the ignition switch to the ON position.
2. Press the driver side power window main switch and fully open the driver side window.
3. Pull up the driver side power window main switch to manual-up position to fully close the driver side window,
and keep holding the switch up at the position for about 2 seconds to complete initial setting.

TWO-STEP DOWN FUNCTION OPERATIVE/NON-OPERATIVE SWITCHING PROCEDURE

Note
? By following the procedure below, the two-step down function is switched to non-operative when it is
operative, and to operative when it is non-operative.

Turn the Ignition on
Within 5 sec
perform the auto open two times
perform the auto close two times

turn the ignition off and within 40 seconds and repeat the above sequence.

Repeat for all the windows.

Aug 14, 2016 | 2007 Mazda 6 2.3

1 Answer

Hello I have a 2006 Mazdaspeed 6 and my buttons on the car are not working but if I use the smart card to unlock/lock it works. And the batteries have been changed. What can I do. Pls help


You must have disconnected your battery for something or your battery died? But to fix, go to all the other 3 windows and push them down until you hear it click twice, then your driver side controls should work again..

CHECK THIS MAZDA OFFICIAL WEBSITE :http://www.mazdaspeedforums.org/forum/f293/2006-mazdaspeed-6-drivers-side-window-controls-101889/

Aug 23, 2013 | Cars & Trucks

2 Answers

Mazda 6 passenger window won't go up!!!


It sounds like it could be the window solenoid, or the window motor. It's unlikely the switches on both doors are bad. Check the solenoids and motors...

Oct 16, 2012 | Mazda Cars & Trucks

2 Answers

2006 mazda 6 just fitted a new battery now one touch power windows dont work


I had the same thing happen when I replaced my battery on my 2006 mazda 6. The program has to be re-programed and it is very simple. Simply push the window button down until window rolls all the way down, then pull up and roll window back up, but dont let go fo the window button for 3-5 seconds after window rolls back up all the way. This resets the program. Do it to both driver and passender side windows and do it with the key in the on position, but not with the motor started. Hope this helps ya

Aug 12, 2010 | 2006 Mazda 6

2 Answers

Passenger window won't work using the driver side control switch


Open the window with the local button and keep the button pressed for 3 seconds after it has fully opened. Then close the window and keep the button pressed for 3 seconds after it has fully closed. This calibrates the position of the window which it lost when you changed the battery. Good luck

Mar 19, 2010 | 2006 Mazda 6

2 Answers

I changed the battery of my mazda 6 and I tried to roll the windows down with the key button and it didn`t work. I dont know if this is a problem with the battery or the computer. thanks


Here is the proper procedure,

POWER WINDOW INITIALIZATION PROCEDURE
1. Turn ignition to ON position.
2. From driver's seat ensure window lockout switch is NOT depressed.
3. Press window switch down to fully open door window.
4. Pull window switch up to fully close door window; hold switch up for two (2) seconds; release switch.
5. Move to front passenger seat and repeat Steps 3 - 4 on passenger window switch.
6. Mazdaspeed6 Only: Move to rear seat and repeat Steps 3 - 4 at left and right rear seat window switches.
7. Verify proper window operation using each door switch.

This was taken from a service bulletin.

Nov 18, 2009 | 2007 Mazda MAZDA6

1 Answer

Auto down window function stopped workin after new battery


Close the window all the way, hold the up button for about 3 seconds, release and check if auto close/open is working.
Do the same to the passenger window.

Regards
Phillip

Sep 18, 2009 | Mazda MAZDA6 Cars & Trucks

1 Answer

Can't control passenger window in mazda 6


Passenger window lost programing. To reprogram, turn the key on, go to the passenger side and with the passemger switch run the window all the way down and hold switch in down position for 2 seconds, then run all the way up and hold in up position for 2 seconds, then repeat again within 5 seconds. Should work from drivers side master switch now.

Sep 05, 2009 | 2006 Mazda 6

2 Answers

New battery in 06 mazda 6


1. Turn ignition switch to "on" position.
2. Open passenger window completely from passenger side window switch.
3. Close passenger window completely from passenger side window switch, and hold switch for an additional 2 seconds.
4. Turn ignition back to "lock" position.

That's it. Works like a champ. And here you thought it was more than just a battery dying....I did.

Aug 11, 2008 | 2006 Mazda 6

Not finding what you are looking for?
2005 Mazda 6 Logo

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...