Question about 2004 Mitsubishi Galant

1 Answer

Evaporator motor bad. Can I replace without removing entier dashboard

No cold air was told evaporator motor bad .$1100 to repair. Can I do this without entire dash removed

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Mitsubishi Master
  • 808 Answers

Yes First remove glove box and lower hush panel the fan motor is in its own separate housing usually held on by 4 12mm nuts it is a trick to get it out from under the dash some times you have to remove the floor carpet.

Posted on Apr 20, 2014

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Can an Evaporator Drain be repair if it's cracked?

ok first i would call the shop that just did the work odds are the drain tube is out of position when they reassembled the evap box

Posted on Aug 09, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace evaporator ?


On what? Front or rear? You will have to evacuate the AC system using a recovery machine. Most evaporator cores are labor intensive involving the entire dash assembly of the vehicle to be removed for access/replacement. Not a job for anyone who does not have mechanical experience in Ac repairs

Jul 01, 2015 | Cars & Trucks

2 Answers

Can an Evaporator Drain be repair if it's cracked?


ok first i would call the shop that just did the work odds are the drain tube is out of position when they reassembled the evap box

Aug 09, 2012 | 2007 Mitsubishi Galant ES

1 Answer

Our front ac is not working and back is cold in our 1999 GMC suburban, we tried putting freon and it didn't work


Dual zone front/rear ac systems have 2 evaporator cores. And 2 orifice tubes, which are just inline
filters. Either your front evaporator core or orifice tube is probably stopped up.

Sometimes you can get to the evaporator cores without removing them from the vehicle, and clean it.
Evaporator cores do get stopped up sometimes, because the blower motor pulls in air with dust and debris from outside, and the air is cooled when it passes through the evaporator core.

But evaporator cores are a nightmare to replace, you usually have to remove lots of stuff under the dash and lots of stuff under the hood to remove them.

Aug 12, 2011 | 1999 GMC Suburban

1 Answer

How to replace a heater core


Heater Core Removal & Installation Front To Remove:
  1. Make sure you have the anti-theft codes for the audio and the navigation system, and then write down the audio presets.
  2. Disconnect the negative cable from the battery.
  3. From under the hood, disconnect the heater valve cable from the heater valve. Turn the heater valve arm to the fully opened position.
  4. When the engine is cool, drain the engine coolant from the radiator.
  5. Disconnect the inlet heater hose and the outlet heater hose from the heater core.
  6. Remove the mounting nut from the heater unit. Take care not to damage or bend the fuel lines, the brake lines, and related parts.
  7. Remove the dashboard.
  8. Remove the evaporator.
  9. Remove the mounting bolts and remove the heater unit. Front heater unit honda-10-00-4128.gif

  10. Remove the self-tapping screws and the clamp.
  11. Carefully pull out the heater core so you don't bend the inlet and outlet pipes.
Front heater core honda-10-00-4129.gif

To Install:
  1. Using care, install the heater core to the heater unit and secure.
  2. Using care, install the heater unit and tighten mounting nuts and bolts to 7 ft-lb (10 Nm).
  3. Install the evaporator.
  4. Install the dashboard.
  5. Connect the inlet heater hose and the outlet heater hose to the heater core.
  6. Connect the heater valve cable to the heater valve.
  7. Refill the cooling system with engine coolant.
  8. Adjust the heater valve cable.
  9. Make sure that there is no coolant leakage.
  10. Make sure that there is no air leakage.
  11. Connect the negative battery cable.
  12. Perform the power window control unit resetting procedure.
  13. Enter the anti-theft codes for the audio and the navigation system, and then enter the audio presets.
Rear To Remove:
NOTE: The rear blower motor, the rear heater core, the blower screen, the rear blower resistor (heating/air conditioning system) and the rear power transistor (climate control system), the rear air mix control motor (climate control system) , the rear mode control motor and the rear expansion valve can be replaced without removing the rear heater-A/C unit.
  1. Remove the self-tapping screws and the clamp, and then remove the bolts and the rear evaporator lines with the rear expansion valve. If necessary, remove the rear expansion valve. Use a second wrench to hold the other fitting on the valve so the rear evaporator lines won't twist. Leave the first fitting loosely connected so you can use it to hold the valve while you loosen the second fitting.
  2. Remove the rear heater hoses.
  3. If necessary, remove the rear blower motor, the rear heater core, the blower screen, the rear blower resistor (heating/air conditioning system), the rear power transistor (climate control system), the rear air mix control motor and the rear mode control motor.
  4. Remove the self-tapping screws and the lower housing.
  5. Remove the self-tapping screws, and carefully separate the left upper housing from the right upper housing. Remove the rear heater core.
Rear evaporator assembly honda-10-00-4116.gif

To Install:
  1. Replace the rear heater core.
  2. Attach the heater hoses.
  3. Make sure no air is leaking from the left upper housing and the right upper housing fitting and from the upper housings and the lower housing fitting.
  4. Before reassembly, make sure that the rear air mix control linkage and door move smoothly without binding.
  5. Before reassembly, make sure that the rear mode control linkage and door move smoothly without binding.
  6. Reassemble the housing.
  7. After reassembly, make sure the rear air mix control motor runs smoothly.
  8. After reassembly, make sure the rear mode control motor runs smoothly.
  9. Refill the cooling system and make sure that there is no coolant leakage.
prev.gif next.gif

Oct 16, 2010 | 2005 Honda Pilot

1 Answer

Hot and cold air simultaneously when A/C is on


U need to find out exactly what the issue is. Is the compressor turning on? If so is it charged properly. If not turning on, is the charge low?

Evaporator is nothing more than a radiator - instead of water in it you have the refrigerant expanding in there and getting real cold and then having a fan blow the air over it. That is AC simplified! Removal of Evaporator not recommended unless it is proven that it absolutely has to be replaced because there is a leak in it. If no leak, leave the sucker alone!.

May 08, 2017 | 1992 Jaguar XJ6

3 Answers

THE BLOWER MOTOR IS MAKING NOISES AND SMELLS


your bearing failed and is causeing friction replace motor

Jun 05, 2009 | 2001 Honda Accord

1 Answer

Freon Leak


the dealer does not want problems with somthing they just fixed so they tend to replace more than needed to be on the safe side ask around and find a good local mom & pop shop they should treat you right

Apr 07, 2009 | 2003 Honda Pilot

2 Answers

Need instruction on installing heater core for 2000 jeep cherokee




The heater-A/C housing assembly must be removed from the vehicle and the two halves of the housing separated for service access of the heater core, evaporator coil, blend-air door, and each of the various mode control doors.

WARNING: On vehicles equipped with airbags, refer to Airbag Systems Safety Information and Procedures. Before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury. See: Restraint Systems\Air Bag Systems\Service Precautions

REMOVAL
  1. Disconnect and isolate the battery negative cable.
  2. Remove the instrument panel from the vehicle. Refer to: Body and Frame, Interior Trim, Dashboard / Instrument Panel, Service and Repair, Instrument Panel Service Procedures, Instrument Panel Assembly Replacement, See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
  3. If the vehicle is not equipped with air conditioning, go to Step 6. If the vehicle is equipped with air conditioning, recover the refrigerant from the refrigerant system. Refer to: Heating and Air Conditioning, Service and Repair, Procedures, Refrigerant System Recovery, See: Service and Repair\Refrigerant System Recovery
  4. Disconnect the liquid line refrigerant line fitting from the evaporator inlet tube.
    • Install plugs in, or tape over all of the opened refrigerant line fittings.
  1. Disconnect the accumulator inlet tube refrigerant line fitting from the evaporator outlet tube. See Refrigerant Line Coupler for the procedures.
    • Install plugs in, or tape over all of the opened refrigerant line fittings.
  1. Drain the engine cooling system.
  2. Disconnect the heater hoses from the heater core tubes. Install plugs in, or tape over the opened heater core tubes.
  3. Unplug the heater-A/C system vacuum supply line connector from the tee fitting near the heater core tubes.
  4. Unplug the heater-A/C unit wire harness connector, which is fastened to the heater-A/C housing next to the blower motor relay.
    1. Remove the five nuts from the heater-A/C housing mounting studs on the engine compartment side of the dash panel. Remove or reposition the evaporation canister for additional access, if required.
    2. Pull the heater-A/C housing rearward far enough for the mounting studs and the evaporator condensate drain tube to clear the dash panel holes.
    3. Remove the heater-A/C housing from the vehicle.
    INSTALLATION
    1. Position the heater-A/C housing to the dash panel. Be certain that the evaporator condensate drain tube and the housing mounting studs are inserted into their correct mounting holes.
    2. Install and tighten the five nuts onto the heater-A/C housing mounting studs on the engine compartment side of the dash panel. Tighten the nuts to 6.2 Nm (55 in. lbs.) .
    3. If the evaporation canister was repositioned during the removal procedure, reinstall it to its proper position.
    4. Connect the Heater-A/C system vacuum supply line connector to the tee fitting near the heater core tubes.
    5. Unplug or remove the tape from the heater core tubes. Connect the heater hoses to the heater core tubes and fill the engine cooling system.
    6. If the vehicle is not equipped with air conditioning, go to Step 10. If the vehicle is equipped with air conditioning, unplug or remove the tape from the accumulator inlet tube and the evaporator outlet tube fittings. Connect the accumulator inlet tube coupler to the evaporator outlet tube.
    7. Unplug or remove the tape from the liquid line and the evaporator inlet tube fittings. Connect the liquid line coupler to the evaporator inlet tube.
    8. Evacuate the refrigerant system. Refer to: Heating and Air Conditioning, Service and Repair, Procedures, Refrigerant System Evacuate, See: Service and Repair\Refrigerant System Evacuate
    9. Charge the refrigerant system. Refer to: Heating and Air Conditioning, Service and Repair, Procedures, Refrigerant System Charge, See: Service and Repair\Refrigerant System Charge
    10. Install the instrument panel in the vehicle. Refer to: Body and Frame, Interior Trim, Dashboard / Instrument Panel, Service and Repair, Instrument Panel Service Procedures, Instrument Panel Assembly Replacement, See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
    11. Connect the battery negative cable.
    12. Start the engine and check for proper operation of the heating and air conditioning systems.
REMOVAL AND INSTALLATION

WARNING: On vehicles equipped with airbags, refer to Airbag Systems Safety Information and Procedures. Before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury. See: Restraint Systems\Air Bag Systems\Service Precautions

  1. Remove and disassemble the heater-A/C housing. Refer to: Heating and Air Conditioning, Housing Assembly HVAC, Service and Repair, See: Heating and Air Conditioning\Housing Assembly HVAC\Service and Repair
  2. Lift the heater core out of the lower half of the heater-A/C housing.
  3. Reverse the removal procedures to install. Be certain that the heater core foam insulator is reinstalled

Jan 18, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2004 Mitsubishi Galant Logo

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...