Question about 2007 Volkswagen Jetta 2.5 Sedan

1 Answer

How to change speed sensor

How do I replace my speed sensor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Volkswagen Master
  • 733 Answers

I THINK U DONT HAVE ONE!!THE CARS SPEED IS RECOGNISED FROM THE ABS SENSORS AS FAR AS I CAN SEE AT MY WIRING DIAGRAMS.WHAT IS UR PROBLEM EXACTLY?

Posted on Apr 24, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, i have an error for my LS430. P0715 Input/Turbine Speed Sensor Circuit Malfunction. I have change the speed sensor and checked the socket but error still come back after few days later. Ant idea?


This is different from speed sensor ! Which sensor did you replace the one on out side of transmission . Turbine speed sensor is inside transmission .

Jun 26, 2016 | Cars & Trucks

2 Answers

Where is the transmission sensor located?


The transmission sensor or speed sensor is located in most vehicle located on the transmission case.These speed sensors are driven by a gear located on the output shaft. The speed sensor's driven gear can be either machined or fastened by a clip. The driven gear is made by plastic to make it softer than the drive gear. It's located on the end of the vehicle speed sensor.

Nov 06, 2015 | 1999 Mitsubishi Galant

1 Answer

Po731 and po700 the car don't change speed


replace the output speed sensor on you 4 speed trans, 3.3 engines only have 4 speed transmissions. The output sensor is located next to the transfer gear. Or if you are looking the two sensors, it would be the one on the right.

P700 = PCM has a transmission code in the EATX controller, and P0731= Gear ratio error in 1st. Replace the output speed sensor and clear the codes.

May 26, 2011 | 1999 Dodge Intrepid

2 Answers

How do I change a speed sensor in a 1996 Honda accord v6


i found a detailed description on utube calledYouTube - 1AAuto.com Replace Install Vehicle Speed Sensor VSS Honda Accord Civic Odyssey Acura CL TL 1992-01

good luck

I changed my speed sensor but it did not resolve the problem still looking 4 a solution

Mar 26, 2011 | 1996 Honda Accord

1 Answer

91 cherokee shifts fine at fist but after a minute or so it wont shift out of first gear. changed the output speed sensor but no change


Sounds like a bad out speed sensor.Are you sure you replaced the correct sensor?This trans(AW340)Has an output speed sensor and a vehicle speed sensor.The output speed sensor is located on the side of tail housing just next to where it bolts to transmission case.The vehicle speed sensor will be about midway of the tail housing or on the transfer case tail housing on the 4x4 models.It may be a good idea to have a tranny shop you trust run a diagnostic and see if you are getting output sensor signal to TCM( transmission control module behind glove box)and take a look at TPS (throttle position sensor)signal when it is hot to make sure you replace the correct part.I have seen bad TPS sensors on these jeep not affect engine drivability because the sensor is really two(one for trans and one for engine)thus the two plugs on the TPS sensor for the automatic Cherokee.Good Luck and let me know if I can help.

Mar 21, 2011 | 1991 Jeep Cherokee Limited

1 Answer

2000 300m shifts into 2nd gear and locks out all other gears. (limp mode) Changed speed odometer sensor, and have pulled #11 fuse, Checked wiring. battery cables removed for re~set. What else can be...


you replaced the output speed sensor, try replacing the input speed sensor, sometimes called the turbine speed sensor, thats where the computer gets the info to shift.

Nov 27, 2010 | 1999 Chrysler 300M

1 Answer

2008 Jeep Commander with 5.8l Hemi problems with instrument panel


Have shop run an OHM test on your transmission sensors -- then have them replaced and rerun the OHM test. -- it's more than likely an input speed sensor that is not working properly and telling the jeep to go into "limp mode" hence your speed isn't changing but it can't read the actual speed.

Apr 13, 2010 | 2006 Jeep Commander

1 Answer

Putting a 4l80e out of a 1996 3/4 ton pick up into my 1998 1/2 ton replacing the stock 4l60e that only has a vss sensor. Could I use the stock harness, if so which speed sensor should I plug it into the...


This isn't going to work without a lot of work. You will need to change the harness and you will likely also have to change the computer. Both speed sensor have to be plugged in

Apr 07, 2010 | 1998 Chevrolet K1500

1 Answer

Instantanious ignition drop out


chek for good engine graund ,inspeckt body graund to.bed graunds on motor and bady will cose lat of hedicks

Mar 12, 2009 | 1989 Chevrolet C1500

Not finding what you are looking for?
2007 Volkswagen Jetta 2.5 Sedan Logo

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...