Question about 1990 Jeep Cherokee Limited

1 Answer

1990 jeep cherokee cranks but wont start I've changed crank sensor,coil,ignition module,and distributor. Has spark,gas,and good combustion pressure and still won't turn on

Posted by on

  • ShadetreeGuy May 11, 2010

    is it in mechanical time?

  • Richard Scordino May 11, 2010

    If you spray carb cleaner into the throttle body while cranking does it start briefly? Also, are you certain that you have the distributor in correctly?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 154 Answers

Check fuses

Posted on Jun 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

97 oldsmobile achieva wont fire changed coil pack spark plugs cam sensor still wont start


Make sure battery has a full charge and battery connections all good.
If it cranks good but won't start, have a helper crank it while you visually check for spark at the spark plugs. If spark everywhere, use a gage and check proper fuel pressure and fuel injector pulse.
If you having a problem with more than one system, I want to check for rpm signal, that usually comes from the crank sensor. Not sure why you replaced cam sensor? I always want to check sensor wiring circuits before replacing anything. Don't replace anything unless your testing points in that direction.

Nov 04, 2016 | Oldsmobile Cars & Trucks

1 Answer

1990 jeep Cherokee won't run but will crank. I hooked my battery up backwards? Everything else in and on my jeep works replaced ignition coil , distributor cap and rotor Any suggestions?


Ign module could be the problem do you have spark when cranking. If you have spark can you hear the fuel pump running while cranking. Let me know

Oct 03, 2015 | Jeep Cars & Trucks

2 Answers

It turns but it wont start,it has gas and power


Pull off the coil ignition cable at the distributor and check for spark coming out of coil when cranking engine over. Use a heavy rag or glove to hold the wire 1/4 inch from a metal ground. Should see a strong blue spark when cranking to verify ignition is good. If no spark, check for battery voltage to coil on the coil primary. If you have current to the coil, suspect a bad coil, ignition module, crank position sensor, or cam position sensor, or pcm. The coil, ignition module, and sensors can be tested before replacing.

Jan 29, 2013 | Cars & Trucks

1 Answer

1993 jeep cherokee cranks but wont start


Look for a crack in the distributor cap or the coil where the cable comes out. you are losing the spark somewhere between these two.

Nov 14, 2011 | 1993 Jeep Cherokee Country

2 Answers

93 honda del sol will turn over but wont start. It has a new time belt, distrib, and the main relay works.


Is it not getting spark or gas? It needs both to run. Both main source. If no spark in any cylinder, then ignition module or crank sensor is likely faulty. If no gas, then fuel pressure regulator or fuel pump or fuel pump relay is bad.

Nov 11, 2009 | 1990 Honda CRX

2 Answers

1996 Jeep Grand Cherokee No Start


I would be thinking that there is a good chance that you need to be checking out replacing the computer, if you aren't getting any communication with the proper scan tool then the computer isn't communicating with anything in the vehicle...... I would have guessed first off that the ignition control module might be bad but that is obviously part of the computer also, I would be looking in that direction.

Sep 19, 2009 | 1996 Jeep Grand Cherokee

1 Answer

95 jeep cherokee seemed to run fine but left overnight it wont


You changed the ignition coil from distributor right?
secondly make sure distributor is not internally shattered (which is a common problem). Normally the current comes from Crank sensor or cam shaft sensor !

Jun 16, 2009 | 1994 Jeep Cherokee Country

1 Answer

No spark at coil


check ignition pick-up coil and ignition module

Mar 31, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
1990 Jeep Cherokee Limited Logo

Related Topics:

348 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...