Question about 2002 Dodge Ram Maxi

2 Answers

Heat only works on high - 2002 Dodge Ram Maxi

Posted by on

  • yadayada
    yadayada May 11, 2010

    replace the blower motor speed control resistor.

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Dodge Master
  • 2,007 Answers

If it's not a resistor, it'll be the blower speed control switch. The one on your dash.

Posted on Jun 19, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 35 Answers

The blower resistor is most likely he problem.

Posted on Jun 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Heated driver seat doesn't heat on 2001 Buick Regal GS


You have probably burnt up the element as it is a 17 year old seat now. The elements are replaceable, but the labor is pretty spendy. To test it you will need a multimeter to check for continuity across the connectors that go to the seat heating elements and check for voltage at the car side of the connector. If you have 12v to one side of the connector and continuity to ground at the other side, and do not have continuity to the seat side between the connectors, you know it is a bad element.

Jan 02, 2018 | Buick Cars & Trucks

1 Answer

Have a 2009 Nissan Quest I can't turn the heat off. Just stays on a high level of blowing out heat .


If you have a fan that has different speed settings (1234, or low med high etc) and the only one that works is high - then the blower resistor pack has failed. If you have a climate control unit (where you just pick a temp you want) then the fan is controlled by the heating system and it sets fan speed. If you have climate control style try lowering the temp to a lower setting (current temp in vehicle) and see if fan slows down. If not then climate control unit or fan resistor bad. If dial type and you get nothing on lower settings (only high works like mentioned above) you need to change blower resistor. It is located under dash near the fan itself. Look for small unit bolted in duct near fan with wire plug going to it.

Feb 23, 2015 | Nissan Cars & Trucks

1 Answer

97 Gmc Sierra my heat only works on high heat sometimes or it doesn't work at all i changed the blower motor and it still doesn't work


You should have a high speed blower relay that provides power on high, and the other speeds go thru a resistor.
The problem could be the actual fan control switch, or the resistor.

Feb 25, 2014 | Cars & Trucks

1 Answer

Heater doesnt blow heat and sometimes works but only on high setting


This depends on what type of heat it is and what you are heating. If it is your car's heating then you have to wait for the car to warm up before hot air blows out.---------------------------------------------------------------------------------------
digiprog 3

Jan 10, 2013 | 2005 Pontiac G6

1 Answer

Heat


You need to replace the blower motor speed control resistor.

Jul 25, 2017 | 2000 Dodge Stratus

1 Answer

My air condition does not work at all and the heat only works on high what could that be?


Two separate issues...but the heat only working on high is caused by a bad blower motor resistor.

Feb 12, 2010 | 1999 Acura 3.5RL

1 Answer

Heating and air conditioning


The blower motor works on high setting ONLY when the blower resistor is bad. The blower motor resistor is held in place with 2 screws and attached into the heater housing under the right side of the dashboard. You can identify the resistor by the big wires that are connected to the connector. If this heating/cooling system is the auto temp type, the part is a bit high on the price.

Feb 10, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Heater control only works on high


You need a blower motor resistor,and the heater blower motor should be checked for high amp draw. check Napa for the part or go to Dodge..prpbably about 60.00 dollars.

Dec 19, 2008 | 1996 Dodge Caravan

Not finding what you are looking for?
2002 Dodge Ram Maxi Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...