Question about 2004 Isuzu Rodeo

1 Answer

4wd switch stays on

Module reset

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 182 Answers

Sometimes after using four wheel drive the light stays on you can put in reverse and it usually goes out if not the sensor maybe bad its located on the front axel mine had a broke wire

Posted on May 02, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anyone know how to reset the service reminder on a 2015 isuzu d-max 2.5 twin turbo?


I would ask the dealer to do this but here is what I show to get the light reset. This is courtesy of expert Techmecho

If the tech 2 device is indicating the code for 4wd module then it has to be replaced.Get the module and its connections checked before going to replace the module.If the module connections are getting short or loose then getting the connections repaired solves the problem.But most probably when it shows module problem,the module has to be replaced.The actual testing procedure is as follows:--- If you have an ODBII code reader, you can check if there are any codes stored in the ECU. There is also a diagnostics mode you can go into for transfer case issues:

1. Warm up the engine. Turn it off.
2. Turn the ignition switch on and off at least twice, then turn the ignition switch to off.
3. Shift into park.
4. Turn the 4WD selector to Auto.
5. Turn the ignition switch to on. Do not start engine.
6. Is the 4WD warning lamp on? Continue if no.
7. Shift into reverse.
8. Turn the 4WD selector to 2WD, Auto, 2WD.
9. Shift into drive.
10. Turn the 4WD selector to 4H, Auto, 4H.
11. Shift into neutral.
12. Turn the 4WD selector to Auto.
13. Shift into park.
14. The 4WD indicator light will come on for 2.5 seconds, then go out. It will then flash a series of times to represent a one or two digit code, with half-second delays within a number and 1 second delay between numbers. e.g. to represent the code 23, it will flash twice with 0.5 seconds between flashes, wait a second, then flash three times with 0.5 seconds between them.Get it rechecked again by disconnecting the 4wd module and reconnecting again,. --------------------Thank you.

May 12, 2016 | Isuzu Cars & Trucks

1 Answer

2004 Tahoe stuck in auto 4wd and service 4wd light is on


switch on dash can cause this but the transfer case control module is the culprit most times.try disconnecting battery this will should reset the TCM.see what happens.worst case senereo is bad transfer case

Dec 10, 2013 | 2004 Chevrolet Tahoe

1 Answer

How to reset my 4wd light? I just installed my new 4wd buttons on my 2005 gmc sierra z71, and my 4wd light still comes on what should I do?


There is no such thing as a reset, if the light stays on a fault exists in the 4X4 control system, the control module has sensed that and turned the light on to alert you to the problem. It is likely that the power transfer case actuator motor is the problem or the wiring to it.

Dec 13, 2011 | 2005 GMC Sierra 1500 Hybrid

1 Answer

I have a 1999 Chevy Silverado. I put the truck in 4WD and it would not come out finally it came out after messing with the buttons a while. The service 4WD was on and then stayed on. I've been dealing...


The service 4WD was on and then stayed on ???? DTC'S - diagnostic trouble codes are stored when that message show's . There is a control module (computer) That makes this 4X4 system work . It's a module problem.

Mar 17, 2017 | Cars & Trucks

1 Answer

Four buttons on dash for 4 wd. won't stay on 2 wd and it goes back to 4wd by itself


Sorry, but three possibilities. Most likely the 4wd actuator motor on the transfer case went bad. This is pretty common. They also encounter switch problems, but it sounds like your switch is doing what it's supposed to. One more thing, there is a 4wd control module, usually in the right kick panel. I'm betting on the shift motor though.

Sep 03, 2011 | 2000 GMC Jimmy

1 Answer

1999 Blazer AUTO 4WD stays lit up in ALL transfer case modes! WHY


the transfer case module is bad it is bolted to transfer case above front drive shaft

Aug 21, 2009 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Complete loss of the 4WD


4x4 shift module in the dash is most likely problem

Jul 25, 2009 | 2001 Dodge Durango

2 Answers

1995 Jeep Grand Cherokee keeps flashing "Service 4WD switch".


You will probably find the oil level in the exchange box is low and the sensor is activating.

Jan 17, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Ford 2005 4x4 problem.


2-Speed Torque-On-Demand (TOD) Operation
The automatic 4-wheel drive (A4WD) system is a 2-speed torque-on-demand (TOD) operation that utilizes the following components:
  • Transfer case
  • 4-wheel drive (4WD) control module (integral to the powertrain control module [PCM])
  • Mode select switch (MSS)
  • Gearmotor encoder assembly (part of the transfer case shift motor)
  • Transfer case shift motor
  • Shift motor sense plate (part of the gearmotor encoder assembly)
Principles of Operation
Transfer Case Shift Motor The externally mounted transfer case shift motor, located at the rear of the transfer case, turns the shift cam assembly. As the shift cam assembly turns, it positions the reduction shift fork for desired transfer case operation. An integral position sensor in the shift motor provides shift motor position information to the 4WD control module.
Mode Select Switch (MSS) The push button MSS, mounted on the instrument panel, allows the operator to select the 4x4 Auto, 4x4 High, and 4x4 Low transfer case operating modes. The indicator light, on the instrument cluster push button, will illuminate only when the 4x4 Low position is engaged.
Visual Inspection Chart Mechanical Electrical
  • Axle shafts and CV joints
  • Driveshaft and universal joints
  • Fluid leaks
  • Matching tire sizes
  • Transfer case shift motor
  • Battery junction box (BJB) fuses:
    • 8 (30A)
    • 17 (5A)
    • 18 (20A)
  • Central junction box (CJB) fuses:
    • 12 (5A)
    • 24 (15A)
  • 4x4 module (PCM)
  • Wiring harness
  • Gearmotor encoder contact plate
  • Connector(s)
  • Circuitry
  • Mode indication switch (MSS)

  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
  1. If the concern is not visually evident, connect the diagnostic tool to the data link connector and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
    • check that the program card is correctly installed.
    • check the connections to the vehicle.
    • check the ignition switch position.
  1. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual.
  1. Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
    • CAN circuit fault; all electronic control units no response/not equipped, refer to Section 418-00 .
    • No response/not equipped for 4WD module (PCM), Go To Pinpoint Test G .
    • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs and carry out the 4WD module (PCM) self test.
  1. If the DTCs retrieved are related to the concern, go to the 4WD Control Module (PCM) Diagnostic Trouble Code (DTC) Index to continue diagnostics. 4WD Control Module (PCM) Diagnostic Trouble Code (DTC) Index
    DTC Description Source Action B1317 Battery Voltage HIGH 4WD Module (PCM) REFER to Section 414-00 . B1318 Battery Voltage LOW 4WD Module (PCM) REFER to Section 414-00 . B1319 Driver Door Ajar Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . B1322 Driver Door Ajar Circuit Short To Ground 4WD Module (PCM) Go To Pinpoint Test M . B1342 ECU is Defective 4WD Module (PCM) CLEAR the DTCs. REPEAT the 4x4 module (PCM) self test. If DTC B1342 is retrieved, INSTALL a new 4x4 module (PCM). REFER to Section 303-14 . CLEAR the DTCs. REPEAT the self test. B1483 Brake Pedal Input Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . B1485 Brake Pedal Input Short to Battery 4WD Module (PCM) Go To Pinpoint Test M . C1729 Transfer Case Unable to Transition Between 4H and 4L 4WD Module (PCM) Go To Pinpoint Test K . C1970 4WD Low Mode Switch LED Short to Battery 4WD Module (PCM) Go To Pinpoint Test K . C1971 4WD Low Mode Switch LED Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1707 Transfer Case NEUTRAL or PARK/NEUTRAL Indication Circuit 4WD Module (PCM) Go To Pinpoint Test M . P1812 Transmission 4-Wheel Drive Mode Select Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1815 Transmission 4-Wheel Drive Mode Select Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1816 Transmission NEUTRAL Safety Switch Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . P1819 Transmission NEUTRAL Safety Switch Circuit Short to Ground 4WD Module (PCM) Go To Pinpoint Test M . P1820 Transfer Case Clockwise Shift Relay Coil Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1822 Transfer Case Clockwise Shift Relay Coil Circuit Short To Battery 4WD Module (PCM) Go To Pinpoint Test K . P1824 4-Wheel Drive Clutch Relay Circuit Failure 4WD Module (PCM) Go To Pinpoint Test H . P1826 4-Wheel Drive Low Clutch Relay Short Circuit to Battery 4WD Module (PCM) Go To Pinpoint Test H . P1827 4-Wheel Drive Low Clutch Relay Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test H . P1828 Transfer Case Counterclockwise Shift Relay Coil Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1830 Transfer Case Counterclockwise Shift Relay Coil Circuit Short To Battery 4WD Module (PCM) Go To Pinpoint Test K . P1849 Transfer Case Contact Plate A Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1853 Transfer Case Contact Plate B Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1857 Transfer Case Contact Plate C Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1861 Transfer Case Contact Plate D Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1867 Transfer Case Contact Plate General Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1891 Transfer Case Contact Plate Ground Return Open Circuit 4WD Module (PCM) Go To Pinpoint Test K . U1900 CAN Communication BUS Fault 4WD Module (PCM) REFER to Section 418-00 . U2023 External Node Fault 4WD Module (PCM) REFER to Section 418-00 . U2051 One Or More Calibration Files Missing/Corrupt 4WD Module (PCM) Reprogram/Reflash the 4x4 module. REFER to Section 418-00 . - For All Other DTCs 4WD Module (PCM) REFER to Section 418-00 .
  2. Your best bet mite be to take it to a qualified repair shop !

May 30, 2017 | 2005 Ford Explorer

Not finding what you are looking for?
2004 Isuzu Rodeo Logo

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...