Question about Cars & Trucks

Open Question

PEUGEOT 607 PETROL ENGINE 4 PISTON TIMING BELT MARK DIAGRAM

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 58 Answers

SOURCE: geo metro timing diagram

woot i feel your pain i had the same problem. go to autozone.com and go to thier vehicle repair.
enter your year make and model and find it. but please hear me on this one.. be carfule thier are like 2 timing references and one timing mark. USE THE DOT. pls i learned the hard way. lol use the dot on the cam sproket. good luck

Posted on Jan 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's your question? How do I set valve timing on peugeot 405 gr petrol?


The link below is a pdf maintenace manual which you can download.. have a look on page 43

http://www.esttools.ee/peugeot/405.pdf

There's also a Youtube video dealing with the 1.8 petrol engine:

How to change timing belt on 1 8l perol Citron Peugeot engine

Apr 23, 2016 | Peugeot Cars & Trucks

1 Answer

Timing chain installation


1996-1999 Toyota Corolla valve timing:
It is very easy to install the timing belt on 1997 Toyota Corolla. Do the following:
- Mark the numbers 1,2 and 3 on the spark plug wires with permanent marker or nail polish and remain the 4th one unmarked. This is necessary so that you can easily remember the spark plug wires order later on their original position.
- Remove the spark plugs so that the engine can easily be rotated.
- Rotate the crankshaft clockwise to align the v- groove mark on the crankshaft pulley with the 0 mark on the timing belt cover. If these marks are aligned the piston is always on the Top Dead Position (TDC).
25502648-okm0ksuj3f3lm2ubjq0dkjux-5-0.jpg

- To replace the timing belt remove the crankshaft pulley, upper and lower timing covers.
- Temporarily screw in the crankshaft bolt in its place to rotate the crankshaft with the spanner and align the v- groove of lower crankshaft gear with the index mark on the oil pump cover as shown in the following diagram.
- Inspect the cam shaft mark through the small hole on the cam shaft sprocket. The punch mark should be exactly behind the hole on the cam shaft sprocket as shown in the following diagram.


25502648-okm0ksuj3f3lm2ubjq0dkjux-5-2.jpg
- Loosen the timing bearing bolt, press the bearing forcefully against the spring with some suitable tool and lock it there temporarily.
- Remove the timing belt.
- Remove the timing bearing.
- Replace the new timing belt and bearing with the original.
- Install in the reverse order of dis-assembly.
NOTE: NEVER PUT EXTRA FORCE ON TIMING BEARING TO ADJUST THE TIMING BELT TENSION. JUST LOOSEN THE TIMING BEARING BOLT AND THE SPRING ATTACHED TO IT WILL PULL THE BEARING IT SELF WITH THE PRESET TENSION TO ADJUST THE TIMING BELT.
Thank you for visiting Fixya.

Mar 02, 2015 | 1997 Toyota Corolla

1 Answer

Ow do I find the timing belt marks on a Peugeot 607 2.2 hdi


Buy a Haynes workshop Manual of 607 or 406. They use the same 202 hdi disel engine.

Jun 15, 2014 | 1991 Peugeot 405

1 Answer

Timing procedure for 2005 suzuki forenza


what engine, most cars have many choices new.. what is yours.
"Displacement or VIN"
cam
or
spark?
btw its really a Daewoo Lacetti from S.Korea makers.
by a real FSM.
or got to alldata.com and read

here is the list of engines
1.4 L 93 bhp (69 kW) Petrol I4
1.6 L 109 bhp (81 kW) Petrol I4
1.8 L 120 bhp (89 kW) Petrol I4
2.0 L 132 bhp (98 kW) Petrol I4
2.0 L 121 bhp (90 kW) Petrol I4
2.0 L 121 bhp (90 kW) Diesel I4

before working on any car, engines. in the USA (where you?)
open hood, look up see that vacuum and smog tag there
and it tells you what engine you have,
than ask questions based on that.

the USA forenza uses the
The US model line features the 2.0 L 4-cylinder E-TEC II made by General Motors, developing a maximum power of 132 horsepower at 5600 rpm.

this is a DOHC engine, 2 cams
and a belt (rubber band engine)
cam timng, im not repeating the 38 steps in the manual or torques/
but the crank cog mark is down aligned with the bottom pan mark
the cams are both at 12pm, aligned with markes on back top pan.

install (cut and past just first 8 steps) 2.0L E-tec II only)
  1. align the timing mark on the crankshaft gear with the notch on the bottom of the rear timing belt cover.
  2. Align the timing marks on the camshaft gears, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
  3. Install the timing belt.
  4. Turn the hex-key tab in a clockwise direction to tension the belt. Turn until the pointer aligns with the notch.
  5. Install the automatic tensioner bolt and tighten to 18 ft. lbs. (25 Nm).
  6. Rotate the crankshaft two full turns clockwise using the crankshaft pulley bolt.
  7. Recheck the automatic tensioner pointer.
  8. Install the front timing belt cover.




Nov 27, 2013 | 2005 Suzuki Forenza

1 Answer

Diagram for volkwagon transporter 1997 2 litre 4 cylinder timing belt replacement


I found a 2.0L VW engine for a Cabrio. Not sure if this is the right one, but here goes:

REMOVAL & INSTALLATION

NOTE: Do not turn the engine or camshaft with the timing belt
removed. The pistons will contact the valves and cause internal engine damage.

Gasoline Engines






Fig. 1: Adjusting the belt tension on a 2.0L 8 valve
91223g06.gif







Fig. 2: Remove the timing belt cover
91223p51.jpg







Fig. 3: Align the timing marks
91223p46.jpg







Fig. 4: Locate the tensioner
91223p47.jpg







Fig. 5: Loosen the tensioner bolt
91223p48.jpg







Fig. 6: Mark the belts direction of rotation
91223p52.jpg



  1. Disconnect the negative battery cable and remove the accessory drive belts,
    crankshaft pulley and the timing belt cover(s).
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to
    TDC of No. 1 piston. The mark on the camshaft sprocket should be aligned with
    the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the distributor cap removed, the rotor should be pointing toward the
    No. 1 mark on the rim of the distributor housing. On 8 valve engines, the notch
    on the crankshaft pulley should align with the dot on the intermediate shaft
    sprocket.
  4. Loosen the locknut on the tensioner pulley and turn the tensioner
    counterclockwise to relieve the tension on the timing belt.
  5. Slide the timing belt from the sprockets.
    To install:

  6. Check the alignment of the timing marks. On 16 valve engines, the mark on
    the tooth should align with the mark on the rear belt cover.
  7. Install the new timing belt and tension the belt so it can be twisted 90┬░at
    the middle of it's longest section, between the camshaft and intermediate
    sprockets.
  8. Recheck the alignment of the timing marks and, if correct, turn the engine 2
    full revolutions to return to TDC of No. 1 piston. Recheck belt tension and
    timing marks. Readjust as required. Torque the tensioner nut to 33 ft. lbs. (45
    Nm).
  9. Install the belt cover and accessory drive belts.
  10. If the belt is too tight, there will be a growling noise that rises and
    falls with engine speed.


Diesel Engines

Some special tools are required. A flat bar, VW tool no. 2065A, is used to
secure the camshaft in position. A pin, VW tool no. 2064, is used to fix the
pump position while the timing belt is removed. The camshaft and pump work
against spring pressure and will move out of position when the timing belt is
removed. It is not difficult to find substitutes but do not remove the timing
belt without these tools.
NOTE: Do not turn the engine or camshaft with the timing belt
removed. The pistons will contact the valves and cause internal engine damage.



  1. Disconnect the negative battery cable and remove the accessory drive belts,
    crankshaft pulley and the timing belt cover(s). Remove the camshaft cover and
    rubber plug at the back end of the camshaft.
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to
    TDC of No. 1 piston. The mark on the camshaft sprocket should be aligned with
    the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the engine at TDC, insert the bar into the slot at the back of the
    camshaft. The bar rests on the cylinder head to will hold the camshaft in
    position.
  4. Insert the pin into the injection pump drive sprocket to hold the pump in
    position.
  5. Loosen the locknut on the tensioner pulley and turn the tensioner
    counterclockwise to relieve the tension on the timing belt. Slide the timing
    belt from the sprockets.
    To install:

  6. Install the new timing belt and adjust the tension so the belt can be
    twisted 45 degrees at a point between the camshaft and pump sprockets. Torque
    the tensioner nut to 33 ft. (45 Nm).
  7. Remove the holding tools.
  8. Turn the engine 2 full revolutions to return to TDC of No. 1 piston. Recheck
    belt tension and timing mark alignment, readjust as required.
  9. Install the belt cover and accessory drive belts.
  10. If the belt is too tight, there will be a growling noise that rises and
    falls with engine speed.


prev.gif next.gif

Oct 29, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

Need a copy of the timing marks for a 1.8 liter turbo for 1999 and engine diagram


1.8 engine but which engine ,is it a petrol or a diesel ,direct injection or indirect injection ,has the timing belt broke did you mark it up with some white paint??

Jun 25, 2010 | Cars & Trucks

1 Answer

Timing belt


  1. THIS IS FOR GAS ENGINE 4 Cylinders A 2.0L SFI (found in 93% of 1996 Volkswagen Golf)
  2. Disconnect the negative battery cable and remove the accessory drive belts, crankshaft pulley and the timing belt cover(s).
  3. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to TDC of No. 1 piston. The mark on the camshaft sprocket should be aligned with the mark on the inner timing belt cover or the edge of the cylinder head.
  4. With the distributor cap removed, the rotor should be pointing toward the No. 1 mark on the rim of the distributor housing. On 8 valve engines, the notch on the crankshaft pulley should align with the dot on the intermediate shaft sprocket.
  5. Loosen the locknut on the tensioner pulley and turn the tensioner counterclockwise to relieve the tension on the timing belt.
  6. Slide the timing belt from the sprockets.

To install:
  1. Check the alignment of the timing marks. On 16 valve engines, the mark on the tooth should align with the mark on the rear belt cover.
  2. Install the new timing belt and tension the belt so it can be twisted 90 ° at the middle of it's longest section, between the camshaft and intermediate sprockets.
  3. Recheck the alignment of the timing marks and, if correct, turn the engine 2 full revolutions to return to TDC of No. 1 piston. Recheck belt tension and timing marks. Readjust as required. Torque the tensioner nut to 33 ft. lbs. (45 Nm).
  4. Install the belt cover and accessory drive belts.
  5. If the belt is too tight, there will be a growling noise that rises and falls with engine speed.

Jan 15, 2010 | 1996 Volkswagen Golf

2 Answers

I need a diagram for the timming belt for a daewoo nubira 2000


what model ?? 8 valve?? 16 valve?? petrol ?? diesel?? .Remove np one spàrk plug and put a long thin screwdriver into hole and turn engine till the piston is at the top and then look for timing marks ,if you still cant see them paint the cam gear .with a couple of spots of white paint ,the lower crank mark it when the keyway points at the top of bottom of the engine.If i remember rightly these opel engines have the timing mark as a white line on the belt .But mark it anyway and always rotate the engine 360% by hand to make sure the valves clear and you have it right

Mar 20, 2009 | 2000 Daewoo Nubira

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

1 Answer

Timing Belt on Passat 2004 2.0 Petrol


should be on the pully wheel if you cant find them bring number 1 piston up to the top dead center and mark on pully

Nov 28, 2008 | 2004 Volkswagen Passat

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...