Question about 1991 Daihatsu Charade

Open Question

Valve settings Valve adjustment setting

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When installing roller rockers on ford f150 5.4 3 valve vin 5 . how many times m,ust i turn the cranckshaft by hand to know im clear of any valve to pistion interference


you open the valve clearance right up as much as you can
any turning with the valve clearance set will bend valves in an interference engine
one the valve timing is set correctly then you adjust the valve clearance

Dec 24, 2017 | Ford Cars & Trucks

2 Answers

How do you adjust idle speed 1991 johnson 100 hp


not important, what's important is that they are absolutely clean, including the four brass high speed jets located in the bottom center portion of the carburetor.

That model engine's carburetors has fixed jets, BUT if the slow speed jets are adjustable, earlier model carburetors have been installed. If so...................

The four adjustable needle valves control the flow of fuel in relation to the set air flow, adjusted as follows (if needed).

(Dual Carb V/4 With 4 (2 each carb) Slow Speed Adjustable N/Valves)
(J. Reeves)

The adjustment procedure of the carburetor slow speed needle valves follows. NOTE... if the needle valves turn too freely, replace the nylon bearing retainer (the nylon item at the front of the carb that the needle valve goes through first) with the newer type RED retainer #315232. If your engine has that weird linkage that connects all four of those needle valves, the newer RED retainers will enable you to discard that linkage. The RED retainers make it impossible for the needle valves to vibrate out of adjustment.

(Carburetor Adjustment - 2 Slow Speed Adjustable Needle Valves, each carburetor)

Initial setting is: All (4) Slow speed valves = seat gently, then open 1-1/2 turns.

Facing the carburetors, start with the top left needle valve, then the top right valve, then the bottom let valve, then the bottom right valve. It may be necessary to redo these steps to get the adjustments ideally set

Start engine and set the rpms to where it just stays running. In segments of 1/8 turns, start to turn the S/S needle valve in. Wait a few seconds for the engine to respond. As you turn the valve in, the rpms will increase. Lower the rpms again to where the engine will just stay running.

Eventually you'll hit the point where the engine wants to die out or it will spit back (sounds like a mild backfire). At that point, back out the valve 1/4 turn. Within that 1/4 turn, you'll find the smoothest slow speed setting.

Do not attempt to gradually adjust all four of the valves at the same time. Do one at a time until you hit the above response (die out or spit back), then go on to the next valve.

When you have finished the above adjustment, you will have no reason to move them again unless the carburetor fouls/gums up from sitting, in which case you would be required to remove, clean, and rebuild the carburetor anyway.

Jun 28, 2017 | Cars & Trucks

1 Answer

Send the valve settings for a toyota 3L engine


Valve setting? Most engine valves have an automatic adjuster to self adjust the setting. You didn't say you had it apart. So, I'm thinking you have a dirty condition that would make the adjuster or valve tap. If so good additives just for both those conditions can restore the adjusting by cleaning and freeing the ailing parts. Try the link below for more info and needed product. Stops noisy engine valve tap in 10 minutes or free Add Driving ends tap

Nov 04, 2014 | 2007 Toyota Hilux 2.7

1 Answer

Code reset factory settings


Yes, but you shouldnt have to. The ECM should adjust your engine under "current" conditons for proper perfomance.
Lee

Nov 02, 2013 | Ford Focus Cars & Trucks

1 Answer

Valve settings


- Pull the hand brake and put transmission in neutral.
- Remove spark plug cords.
- Remove the spark plugs.
- Remove the Tappet cover
- Lift up the left front wheel.
Cylinder number 1 is toward the pulleys and belts side.
- Rotate the crankshaft anticlockwise with socket and extension rod and bring the valve tappets (intake and exhaust) No. 4 cylinder on dancing position.
NOTE: THERE ARE OTHER WAYS ALSO TO ADJUST THE FOUR VALVES AT A TIME. BUT AS DIY FOLLOW THE FOLLOWING METHOD TO AVOID ANY CONFUSION.
- Adjust the valve clearance of number 1 cylinder.
Valve clearance:
Intake 0.18 - 0.22 (cold) Exhaust 0.25 - 0.28 (cold)
- Rotate the crankshaft anticlockwise to bring the valves of cylinder 2 on dancing position and adjust the valves of No. 3 cylinder.
- Similarly rotate the crankshaft to bring the valves of No. 1 cylinder on dancing position and adjust the valves of No. 4.
- Rotate the crankshaft anticlockwise to bring the valves of cylinder No. 3 on dancing position and adjust the valve clearance of No. 2 cylinder.

May 04, 2013 | 1999 Honda Civic

1 Answer

What is the valve settings


If you have adjustable tappets the setting are usually .010" hot inlet and .12" hot exhaust. Start at 12 and 14 cold and recheck when hot. If you have hydraulic tappets there is no adjustment as they automatically adjust when oil pressure is achieved

Jan 26, 2013 | Cars & Trucks

1 Answer

76 351 mod 400 has a noise that sounds like the rocker arms are loose .Are they adjustable?


Yes the are adjustable, if they are the original camshaft lifters and rockers they should be hydraulic and the adjustment is 0 valve lash.

1976 is getting back there and some wear along the line someone might have changed them, remove a valve cover and see if there is a set screw on the rocker arm if there is they have been changed to a solid set and you will have to adjust them try .006 intake and .008 exhaust.

Nov 17, 2010 | 1981 Ford F 150

1 Answer

Valve adjustment


tiburon uses hydrolic lash adjusters there are no valve lash adjusting If you hearing a pecking sound on the top of the mtr try some oil additive or replace the hydrolic lash adjusters

Jun 15, 2009 | 2001 Mitsubishi Eclipse

Not finding what you are looking for?
1991 Daihatsu Charade Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...