Question about Chrysler Pacifica

Open Question

04 Chrysler pacifica will not crank ground wire location

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Where are the spark plugs located in a 2005 Chrysler Pacifica?

Jay from Ma,
You have it backwards the rear three are accessable with the front three being under the intake. To remove the intake simply remove throttle body and aproxamently 15 other bolts.

Posted on May 08, 2009

  • 176 Answers

SOURCE: I NEED TO FIND A 2004 CHRYSLER PACIFICA WIRING

Go to your local Napa parts store. If they have updated computers, they can print out your wiring diagram for free.

Posted on Oct 25, 2009

  • 47 Answers

SOURCE: positive ventilation crank case valve location

I have one of these cars too, also 3.5. I purchased with 34K and has used a quart of oil every 1000 miles since then. It has no leaks or smoke or any other signs of oil consumption. So much research, nobody knows why these engines do this, some have gone as far as contacting Chrysler just for them to say, " that's normal". But here is the diagram for the PCV:

db8978e.jpg

Posted on Mar 13, 2010

  • 1 Answer

SOURCE: location of map sensor on 04 chrysler pacifica

Sensor is located passenger side of the intake and mounts facing the firewall .It takes a torx bit to remove .NOT a philips as screw is hard to see from the front.I use a bit with a 1/4 in socket as a full size screwdriver will not fit.Remove screw and use a set of pliers to twist and pull back.

Posted on Mar 24, 2010

  • 46 Answers

SOURCE: I have a 2004 Chrysler Pacifica

136266353that would be your HO2 sensor. It's located in the left hand exhaust manifold closer to the top of the engine. It usually takes a special socket to remove one. If you have any doubt, take it to a shop and have them replace it for you. This sensor effects fuel and driveability, don't go to long without fixing it as it may cause damage to your catalytic convertors.

Posted on May 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix the horn in 04 Chrysler Pacifica


Do you know what a relay is and how it works ? Find the horn relay in the under hood fuse box ! Watch this video . VEHICLE RELAYS Operation Diagnosis Also watch this video ! Chrysler , Dodge and Jeep have known problems with TIPM - totally integrated power module . Chrysler Pacifica TIPM Electrical Problems Was a bad ground .

Jan 18, 2017 | Chrysler Cars & Trucks

1 Answer

04 pacifica ground problem. Need ground wire locations .


where is the ground problem. most grounds are under the hood bolted to frame and fenders

Dec 30, 2016 | 2004 Chrysler Pacifica AWD

1 Answer

Chrysler pacifica won't engage stater


Ground wire for the starter is corroded through. Try running a new ground wire.

Jul 14, 2014 | 2004 Chrysler Pacifica

1 Answer

04 pacifica starts and and shut down while driving


did u check the ground on the frame beside the transmission

Feb 07, 2014 | 2004 Chrysler Pacifica

2 Answers

Car cuts off when putting it in reverse, chrysler pacifica 2005


Check the engine mounts for being broken and the wiring around the engine for chaffing and the ground cables.

Nov 24, 2012 | 2006 Chrysler Pacifica

1 Answer

Where is the alternator located in the chrysler 04 pacifica/


The alternator is hiding under the engine cover. You must remove the engine cover if you have one. Locate the power steering fluid resevior. The alternator is right behind it.

Oct 24, 2010 | 2004 Chrysler Pacifica

2 Answers

Our pacifica will not start. The lights will come


It sounds like a very weak battery issue.

Jan 06, 2010 | 2004 Chrysler Pacifica

1 Answer

I NEED TO FIND A 2004 CHRYSLER PACIFICA WIRING DIAGRAM WE ARE HAVING A GROUND ISSUE AND NEED TO FIND OUT WERE THE GROUND IS BAD


Go to your local Napa parts store. If they have updated computers, they can print out your wiring diagram for free.

Oct 25, 2009 | 2004 Chrysler Pacifica

2 Answers

Chrysler Pacifica will not start.


I had the same problem, could not figure it out. Looked all over the inter net found a post that said something about the ground wire that had a bad connection. So i followed the found wire and this is what i found. attached photos, plus whati did to fix it.
9_8_2012_8_50_27_pm.jpg9_8_2012_8_50_37_pm.jpg

Feb 04, 2009 | 2004 Chrysler Pacifica

2 Answers

Car won't crank & makes a clicking noise when ignition is turned.


Is this the original battery? Have u had it tested? The no crank, clicking noise is classic dead battery symptoms, lights can still work, but not enough power to turn engine over. If it's the original battery, it's at the end of it's life cycle, and should be replaced. U can get the battery tested for free at any parts store.

Dec 29, 2008 | 2004 Chrysler Pacifica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...