Question about Toyota Sequoia

2 Answers

How to program a remote transmitter for a Toyota Sequoia 2005 SR5

I only received one transmitter when I bought the vehicle. I have purchased another one online, but I need to know how to program the transmitter

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Use this website. It will work for the Toyota Sequoia, and best of all, it is free!!

http://www.programyourremote.com/classified/Browse.asp?cid=296

Posted on Jul 07, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 85 Answers

Go to a toyota dealer with a scan tool.they will program the key for you! in minutes! voooop!

Posted on Jun 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i replace my 2001 sequoia immobilizer


There are several parts to this system. Have the codes read. Security is built into the BCM. The BCM sends a signal to the ECM/PCM to start the car. Both of these have to be programmed, you can't just replace them. You have other parts also that can set security.

Aug 06, 2015 | 2005 Toyota Sequoia SR5

1 Answer

Where would I find the wireless door lock control receiver on a 2005 Toyota Sequoia?


This site should help http://www.villagetoyotaparts.com/showAssembly.aspx?ukey_product=2418097&ukey_assembly=356348



1 is the receiver 2 is the transmitter

Check for wire damage fuses connectors before changing as these parts are not cheap. I think the receiver is between 300 and $500 us. May get a used one for less but you will need to investigate the programming requirements.

Feb 11, 2015 | 2005 Toyota Sequoia SR5

1 Answer

My sequoia 2005 master key was stolen, how can I start my car again I just have a key to open doors?


You have to talk to your local dealership. The vehicle may need to be towed in and the dealership will make you a new key. Call first. You may just be able to take in your title and have a key made.

Dec 07, 2014 | 2005 Toyota Sequoia SR5

1 Answer

2005 saturn relay fob programming


TRANSMITTER PROGRAMMING
IMPORTANT: All transmitters which are to be recognized by the remote control door
lock receiver (RCDLR) must be programmed in a single programming
sequence. If the system is placed in program mode it will erase all
previously programmed transmitters upon the receipt of the
programming signal from the first transmitter. Up to 4 transmitters can
be programmed. Do not operate or program the transmitters in the
vicinity of other vehicles that are in the keyless entry program mode.
This prevents the programming of the transmitters to the incorrect
vehicle.
Install 1. a scan tool.
Use the scan tool in order to access the Body Control Module (BCM) Special Function or
Module Setup: Program Key Fobs.
2.
3. Press the START soft key on the scan tool.
IMPORTANT: The scan tool must stay connected until all of the transmitters are
programmed.
Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter.
After a delay of 5-10 seconds, the scan tool will indicate that the transmitter is programmed.
4.
5. Repeat the previous step in order to program up to 4 transmitters.
6. Remove the scan tool.
7. Operate the transmitter functions in order to verify correct system operation.

Sep 14, 2012 | 2005 Pontiac G6

2 Answers

2003 remote control for 2005 van?


Transmitter Programming
If you lose a transmitter, program the old and new transmitter(s) into the remote control door lock receiver's memory. Up to 4 transmitters may be programmed.


Important
Once the remote control door lock receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information, requiring the programming of all transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If more than 1 receiver is being programmed at the same time, it is possible that the same transmitter could be programmed to more than 1 remote control door lock receiver.


Perform the following steps in order to program the transmitter:

Remove the ignition key from the ignition lock cylinder.
Remove the BCM PRGRM fuse from the fuse panel. Refer to Fuse Block in Wiring Systems.
Close all of the doors.
Close the liftgate.
Turn the ignition lock cylinder to ACC.
Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second.
Open and close any vehicle door. A chime will be heard when the system enters the BCM programming/diagnostic mode.

Important
After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat the previous step on each additional transmitter to be programmed.
Remove the ignition key from the ignition lock cylinder.
Install the BCM PRGRM fuse back into the fuse panel. Refer to Fuse Block in Wiring Systems. IF THIS WAS HELPFUL,PLEASE RATE,THANK YOU

Jul 15, 2010 | 2005 Pontiac Montana

1 Answer

How to program 2005 toyota sequoia garage door opener?


Hello.I will be glad to help you out.

Choose which of the 3 buttons you wish to use, on the car.

Take the remote transmitter, depress the actuator button, and continue to hold it until advised to release.

Depress the button, on the car, of your choice, and hold it down until advised to release.

Hold the garage door actuator (while holding the actuator button down) above the car's 3 buttons.

Rotate the door transmitter until the red light above the 3 buttons starts to flash slowly.

Stop moving the remote around when the light flashes slow.

Within several seconds, the same light n the car will now flash rapidly.

Release the car's button, release the transmitter button.

Verify that the door now operates..

Nov 29, 2009 | 2006 Toyota Sequoia

1 Answer

We purchased a 03 lincoln lsand need to reset the keyless entry


1. Sit in the vehicle driver's seat.
2. Remove the ignition key from the ignition lock cylinder.
3. Close all of the vehicle's doors.
4. Remove the MALL PGM fuse from the fuse panel. Or reset the fuse which controls your keyless remote.
5. Turn the ignition lock cylinder to the ACC position.
6. Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
7. Open and then close any vehicle door. You will hear a chime when the
remote control door lock receiver enters the programming/diagnostic mode. If
you do not hear a chime, start again at step 1.

This is an important fact here:

After 7 seconds, you may hear a chime confirming successful synchronization.
After approximately 14 seconds, you will hear a chime confirming successful
programming.

8. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for
14 seconds.
9. Repeat step 8 in order to program each additional transmitter.
10. Remove the ignition key from the ignition lock cylinder.
11. Install the MALL PGM fuse back into the fuse panel.

This is important as well:
Once the keyless entry receiver enters the programming/diagnostic mode, the
programming of the first transmitter erases all previous transmitter
programming information. You must then program all of the transmitters.
Program only 1 vehicle remote control door lock receiver at a time. If you
program multiple receivers simultaneously, the same transmitter could
possibly be programmed to more than 1 remote control door lock receiver

The fuse should be in your fuse block of your vehicle.

May 25, 2009 | 2003 Lincoln LS

4 Answers

Keyless remote


THIS IS THE PROCEDURE, FOLLOW IT EXACTLY OR IT WILL NOT WORK.



Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:

Sit in the vehicle driver's seat. (actually it’s much ezr from the front pass seat)
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation

Sep 25, 2008 | 2006 Pontiac G6

1 Answer

How do you program the garage door remote?


Turn the key to the "ON" position; do not start the vehicle.

Press on the button of the 3 available to you on the vehicle and hold it until advised to release it.

Take your garage door remote transmitter, and press the button that you use to make the garage door operate, hold it down until advised to release.

With the vehicle button being depressed, and the remote button depressed, hold the remote up against the area where the 3 buttons are located. It needs to touch the area wher the buttons are.

Keep moving the remote around slowly, back & forth, spin the remote, until the red light starts to blink slow.
After the light begins to blink slow, hold the remote in that exact position until the lamp blinks real fast.
Relase both buttons.
Repeat for a second remote on another button.

Jun 29, 2008 | 2001 Toyota Sequoia

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

682 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...