Question about 1998 Holden VT Commodore

1 Answer

Remove power steering pump on commodore vt

How to remove pump which is the best way and in what order do you need special tools

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 79 Answers

Im assuming you are asking about how to remove p/s pump on a v6 commodore.
1.place a drain try under vehicle to collect p/s fluid.
2.on the p/s pump pulley you will see 4*10mm bolts release them.
3.remove drive belt
4.now remove p/s pump pulley.
5.undo p/s return line
6.release and undo abt half way 2*13mm bolts that mount p/s pump to engine block.
7.on the rear of the pump you will see the metal feed pipe use a pipe spanner to undo it 16mm
8.finish undo the 13mm bolts hold pump on ,once these bolts are off the pump will come away..

Posted on Feb 22, 2015

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6468 Answers

SOURCE: VT Commodore Wagon probs with fuel pump replaced orig. pump with GOSS worked for week now wont pump

sounds like you have a bad electrical connection you moved around when doing the pump

Posted on Jul 04, 2012

emissionwiz
  • 76846 Answers

SOURCE: How to remove the front headrest of Holden 2008 SV6 commodore ?

You need a special tool that slides down the side of the head rest shaft and release the spring clip retainer.

Posted on Jul 12, 2012

  • 72 Answers

SOURCE: Remove ignition barrel in vt commodore

you need to have the key in the ignition take the shrouds off there is a small hole underneath the barrell you have to push something small into the hole then pull out the barrell

Posted on Apr 09, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power steering pump 2007 Ford Edge located where? Can't seem to locate it..need to replace it; 3.5 engine


CAUTION: While repairing the power steering system, care should be taken to prevent the entry of contaminants or premature failure of the power steering components may result.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 .
  1. Using a suitable suction device, siphon the power steering fluid from the power steering fluid reservoir.
  1. Remove the RH inner fender splash shield. For additional information, refer to Section 501-02 .
  1. Using the special tool, disengage the power steering pump belt from the power steering pump pulley and position it aside.
    • Install the removal tool between the belt and the pulley and turn the crankshaft bolt clockwise to disengage the belt.
  1. Remove the 4 bolts and position the driveshaft aside.
  1. Using a suitable jack, support the rear of the subframe.
  1. Remove the 2 nuts, 4 bolts and the subframe support brackets.
  1. Remove the 2 middle subframe nuts.
  1. Lower the rear of the subframe.
  1. Release the clamp and disconnect the power steering supply hose from the power steering pump.
  1. Disconnect the power steering pressure (PSP) switch electrical connector.
  1. Remove the power steering pressure line fitting banjo bolt and disconnect the line from the power steering pump.
    • Discard the 2 seals.
  1. Remove the 3 power steering pump bolts and the power steering pump. This is a job best left to a qualified repair shop !

Jul 26, 2016 | 2007 Ford Edge

1 Answer

Power sterring makes wering noise and gose hard at low revs


Power steering makes wering noise and goes hard due to more than like been very lowe on pwer steering fluid .

1.power steering pumps normal leak fluid in the commodores and need replacing.
2.steerings always leak.
3.Also check the hose that come from the p/steer resvoir and even p/steeer cooler hoses and the metal pipe that mounted at the front of the radiator these are all very common faults

May 24, 2014 | 1998 Holden VT Commodore

1 Answer

How to remove power steering pump from 1993 chevy k1500


It is a pretty easy task but you will need a special tool for getting the pulley off of the pump. First remove your belt and make note of how it is routed before you remove it so you now how it goes back on. Then you need to remove the power steering pump pulley with a pulley remover tool. Then remove the oil lines and then unbolt it from the mounting bracket.

May 04, 2011 | 1993 Chevrolet K1500

1 Answer

How do I get my power steering pump out of 2002 yukon


Hello walker_227,

Removal Procedure:

SPECIAL TOOLS: You will need a power steering pulley remover and installer tool, DO NOT USE A HAMMER.

1. Remove the power steering pulley.
2. Raise the vehicle.
3. Remove the oil pan skid plate from the vehicle, if equipped.
4. Place a drain pan under the vehicle.
5. Remove the power steering pressure hose from the power steering pump from underneath the vehicle.
6. Lower the vehicle.
7. Remove the return hose from the power steering gearbox and the power steering pump.
8. Remove the bolt retaining the rear bracket to the engine.(See picture below)
9. Remove the bolts from the front of the pump.(See picture below)
10. Remove the pump from the vehicle.
11. Remove the bracket from the rear of the pump

Installation Procedure:

1. Reverse above procedure
2.Fill and bleed the power steering system.

netvan_20.png

Mar 14, 2011 | 2004 GMC Yukon

1 Answer

Repair power steering for 1994 Chevy S10 Blazer V-6, pump and houses.


Power Steering Pump Removal & Installation 2.2L Engine To Remove:
  1. Remove the upper cooling fan shroud.
  2. Position a fluid catch pan under the power steering pump.
  3. Disconnect the feed and return hoses from the power steering pump, then drain the excess fluid into the catch pan. NOTE: On models equipped with a remote fluid reservoir, disconnect and plug the hose(s) in order to prevent system contamination or excessive fluid loss.
  4. Remove the drive belt from the pulley.
  5. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump. NOTE: When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
    Installing the pilot bolt 85388111.gif

    Removing the power steering pump pulley 85388113.gif

    Installing the power steering pump pulley 85388114.gif

  6. Unplug the electrical connection from the A/C compressor, unfasten the compressor mounting bolts and set the compressor to one side without disconnecting the lines.
  7. Remove the front mounting bolts and the rear bracket nuts from the studs on the engine.
  8. Remove the rear brace mounting bolt.
  9. Remove the power steering pump from the vehicle.
To Install:
  1. Position the pump to the vehicle and secure using the front retaining bolts to 22 ft. lbs. (30 Nm).
  2. Install the rear bracket bolt and nuts. Tighten the retainers to 22 ft. lbs. (30 Nm) on 1994 - 97 models and 37 ft. lbs. (50 Nm) on 1998 and later models.
  3. Install the A/C compressor.
  4. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end. NOTE: When positioning the installer tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
  5. Properly install the drive belt.
  6. Remove the caps, then connect the feed and return hoses to the pump.
  7. Properly refill and bleed the power steering system.
  8. Test drive the vehicle.
4.3L Engine To Remove:
  1. Remove the upper cooling fan shroud.
  2. Remove the drive belt.
  3. Remove the fan and clutch from the water pump.
  4. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump.
  5. Safely raise and support the vehicle.
  6. Remove the shield from the steering linkage.
  7. Position a fluid catch pan under the power steering pump.
  8. Disconnect the return hose from the power steering pump, then drain the excess fluid into the catch pan.
  9. Safely lower the vehicle.
  10. Disconnect the pressure hose from the pump and cap the open line.
  11. Remove the filler neck tube.
  12. Remove the power steering pump mounting nuts and bolts.
  13. Remove the power steering pump from the vehicle.
NOTE: When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
Installing the pilot bolt 85388111.gif

Removing the power steering pump pulley 85388113.gif

Installing the power steering pump pulley 85388114.gif

To Install:
  1. Position the pump to the vehicle.
    • Tighten the front retaining bolts to 37 ft. lbs. (50 Nm) and the nuts to 31 ft. lbs. (41 Nm).
  2. Install the filler neck tube.
    • Tighten the bolt to 15 ft. lbs. (20 Nm).
  3. Connect the pressure hose to the pump.
  4. Safely raise and support the vehicle.
  5. Connect the return hose to the vehicle.
  6. Install the shield on the steering linkage and lower the vehicle.
  7. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end. NOTE: When positioning the installer tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
  8. Install the fan and clutch on the water pump.
  9. Properly install the drive belt. NOTE: Be sure to secure any hoses which may get in the way or rub other components.
  10. Install the upper fan shroud.
  11. Properly refill and bleed the power steering system.
  12. Test drive the vehicle.
prev.gif next.gif

Nov 05, 2010 | Chevrolet S 10 Cars & Trucks

2 Answers

Power steering pump, broken, how to replace


Power Steering Pump - REMOVAL & INSTALLATION

3.0L OHV (2 valve) Engine
(see Figures 1 and 2)

1f2a309.jpg

Fig. 1: Power steering system-3.0L OHV (2-valve)

0111341.jpg

Fig. 2: A few special tools are required to remove and install the pulley on the power steering pump
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belt.
  3. Remove the alternator.
  4. Drain and remove the radiator coolant recovery reservoir.
  5. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  6. Remove the idler pulley from the power steering pump support.
  7. Remove the bracket mounting bolt located under the belt tensioner mounting.
  8. Remove 2 retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  9. Clamp the pump support bracket in a suitable vise.
  10. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the 3 bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.
To install:
  1. Install the power steering pump to the power steering pump support.
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 17-24 ft. lbs. (23-32 Nm).
  4. Complete the installation by reversing the removal procedure.
  5. Fill the power steering reservoir with power steering fluid.
  6. Connect the negative battery cable.
  7. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.

Hope this helps.

Sep 06, 2010 | 1996 Ford Taurus

1 Answer

Alternator bracket broke and can not get to last bolt to get it off to have welded. Any suggestions appreciated.


Is this the bracket that has the power steering pump under the alternator? If so the power steering pump has to be removed to remove bracket. To remove power steering pump you have to remove the pump pulley with a special tool and then press it back on with another tool. Both tools can be rented at your local Advanced auto parts store.

Jun 02, 2010 | 1984 Chevrolet Blazer

Not finding what you are looking for?
1998 Holden VT Commodore Logo

275 people viewed this question

Ask a Question

Usually answered in minutes!

Top Holden Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you a Holden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...