Question about 1999 Dodge Intrepid

Open Question

Where is crank sensor for 1999 intrepid - 1999 Dodge Intrepid

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 35 Answers

SOURCE: My 1999 dodge intrepid is hesitating to start but wont start

The MAP sensor. Do you have a check engine light on?

Posted on Apr 29, 2009

Ad
  • 54 Answers

SOURCE: Vehicle stalls sometimes

could be either the cam sensor or crank sensor , but I would check the crank sensor first , this sensor will not cause a check engine light either

Posted on May 26, 2009

  • 4 Answers

SOURCE: Crank shaft sensor location.

Underneath on the transmission housing.

Posted on Jul 03, 2009

roniecon
  • 6826 Answers

SOURCE: 1999 dodge intrepid es 3.2L

Replace the coolant temp sensor to solve the problem.

Posted on Aug 20, 2010

Autotroubles
  • 987 Answers

SOURCE: I NEED TO KNOW THE

Cam sensor is right in front under the planum and crank sensor is by the crank harmonic balancer pully. But why do you ask?

Posted on Mar 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I NEED TO KNOW THE LOCATION OF THE CAM SENSOR AND CRANK SENSOR ON MY 1999 DODGE INTREPID 2.7 LITER


Cam sensor is right in front under the planum and crank sensor is by the crank harmonic balancer pully. But why do you ask?

Mar 03, 2011 | Dodge Intrepid Cars & Trucks

1 Answer

Code1391


I would check the throttle patrol sensor

Jul 03, 2009 | 1999 Dodge Intrepid

1 Answer

Dodge intrepid 1997 3.5 engine code p0320


This means there is no crank reference at the pcm the crank sensor is a common problem with that vehicle but I would be sure to check for bad wiring or lose connection from the crank sensor to the pcm also the. If no problem with the wiring and the crank senor test bad then change it. The dealer would recommend also changing the cam sensor as well but I have just replaced the crank sensor and fixed with no probs(if the wiring has not been damaged have seen that before mainly where the wiring can rub at the crank near the bottom

Jul 03, 2009 | 1999 Dodge Intrepid

1 Answer

Vehicle Stalls


you should have engine light on and engine codes
if its the cam or crank sensors, shouldn't be the starter i would start with the ingition switch.

May 28, 2009 | 1999 Dodge Intrepid

1 Answer

Vehicle stalls sometimes


could be either the cam sensor or crank sensor , but I would check the crank sensor first , this sensor will not cause a check engine light either

May 26, 2009 | 1999 Dodge Intrepid

2 Answers

My 1999 dodge intrepid is hesitating to start but wont start


The MAP sensor. Do you have a check engine light on?

Apr 26, 2009 | 1999 Dodge Intrepid

2 Answers

Location of the camshaft and crankshaft sensors


cam sensor is on the driver side, front of the motor, just below the valve covers in easy veiw, just outboard of the water temp sensor and they both share the same wiring harness.  The cam sensor is on the passenger side, actually on the transmission bell housing.  It takes the signal from the flywheel next to the ring gear, about an inch from the engine on the transmission bellhousing.  Accesible from the top and easier if you remove the air filter duct.  Or jack up the front passenger side and easier if you come in from the front and its behind the axel, behind the motor, go up the bell housing, just below crank shaft level.  Go with this first , it tells the comp when to send fuel.  If you're getting spark with a 1381 code and you're choosing between CAM & CRANK, start with this, this is the culprit.  Consider getting it from the dealer.  Good luck.  This is Waverunner70, Hope I could help.

Feb 28, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
1999 Dodge Intrepid Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...