Question about 2011 Mercedes-Benz Sprinter

Open Question

Shift selector switch location - 2011 Mercedes-Benz Sprinter

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the location of the neutral safety switch on a 2005 3.6 liter v6 Buick lacrosse cxs


Should be part of the shift selector switch mounted on the shift lever where it exits the transmission.

Dec 09, 2015 | Buick Cars & Trucks

1 Answer

Brake shift interlock solenoid


column or floor shifter ?
Brake Shift Interlock Actuator - Floor Shift Removal and Installation
NOTE: The brake shift interlock actuator is not serviced individually. If replacement is required, install a new floor shift selector lever assembly.
For additional information, refer to Selector Lever - Floor Shift in this section.
Brake Shift Interlock Actuator - Column Shift Removal and Installation
  1. Set the parking brake.
  1. Remove the steering column shrouds.
  1. Turn the ignition to the accessory position and apply the brake or actuate the brake shift interlock actuator (BSIA) override.
  1. Put the selector lever into the NEUTRAL position.
  1. Disconnect the BSIA electrical connector.
  1. Remove the BSIA screw.
  1. Gently pry the clip up and remove the BSIA.
  1. NOTE: During installation, verify that the BSIA override has been activated and the slider is fully rearward. Before rotating the selector lever from NEUTRAL into PARK, align the selector lever tab into the BSIA. To install, reverse the removal procedure.

May 26, 2017 | Ford Expedition Cars & Trucks

1 Answer

Location of neutral safety switch on 1994 toyota land cruiser?


It's located on the right side of the transmission where the shift selector rod attaches to the selector lever on the trans, near the front of the transmission, it also has a large electrical connector on it.

Feb 28, 2012 | 1994 Toyota Land Cruiser

1 Answer

WHERE IS THE NEUTRAL SAFTEY SWITCH LOCATED ON A 1992 HONDA ACCORD AUTOMATIC TRANSMISSION


it's under the console--see picture and instructions below and let me know if you have more questions.

fe6c30d.gif
To replace the shift position switch, firmly set the parking brake and block the wheels. Place the shift selector in N. Remove the console. The switch is located on the side of the shift selector, held by 2 bolts or nuts. Unplug the wiring connectors, then remove the switch.
When installing the switch, make sure the switch slider is positioned to align with the shifter arm or tab. Install the switch, tighten the retaining nuts or bolts and connect the wiring. Reinstall the console.
After installing the switch, check that the engine starts only in P or N; the starter should not engage with the shifter in any other position. Check also that the back-up lights come on when the selector is placed in R.

Oct 26, 2010 | 1992 Honda Accord

2 Answers

When I have a no start condition I work the maul selector from park to low 1 back and forth and the car starts


Your safety interlock switch is going out or is not adjusted properly. There is a procedure for adjusting the switch. The switch is on the transmission in the engine compartment. If you want to adjust the switch, loosen the botls holding the switch and follow steps 7-8 below. Else, you can just replace the switch entirely by following all steps.

The neutral start and backup switch are one unit mounted on the top left end of the transaxle. The neutral start portion of the switch allows electrical current to travel to the ignition system when the shift selector is in park or neutral only. The vehicle will not start when the selector is in any other gear. The backup portion operates the rear backup lamps when selector is in the reverse gear.


REMOVAL & INSTALLATION See Figures 1 and 2

  1. Make sure the shift selector in the Park position, then apply the emergency brake.
  2. Disconnect the negative battery cable.
  3. Disengage the neutral start switch electrical connector, then remove the shift control lever on top of the switch.
  4. Remove the two neutral switch attaching bolts, then remove the switch.

d6b1e99.gif


Fig. Fig. 1: Neutral safety switch location-vehicles equipped with automatic transaxle

8bf90b7.gif

Fig. Fig. 2: Adjusting the neutral safety switch



To install:

  1. Install the switch on the manual shaft.
  2. Loosely install the two attaching bolts and washers.
  3. Insert a No. 43 drill (0.089 in.) through the hole.
  4. Tighten the attaching bolts to 7-9 ft. lbs. (9-12 Nm), then remove the drill.
  5. Engage the switch electrical connector, then connect the negative battery cable.

Sep 22, 2010 | 1992 Ford Taurus

1 Answer

Neutral safty switch


Back-Up Light Switch/Neutral Safety SwitchREMOVAL & INSTALLATION
(see Figure 1)

On automatic vehicles, functions of both the reverse lamps and the neutral safety switch are controlled by the shift position switch at the base of the shift selector. This multi-circuit switch also sends signals to the various electronic control units (cruise control, automatic transaxle ECU, etc.), keeping them advised of the selected gear.

5d7324d.jpg

Fig. 1: Reverse lamp and neutral safety switch functions are both controlled by a shift position switch at the base of the shift selector

To replace the shift position switch, firmly set the parking brake and block the wheels. Place the shift selector in N. Remove the console. The switch is located on the side of the shift selector, held by 2 bolts or nuts. Unplug the wiring connectors, then remove the switch.

When installing the switch, make sure the switch slider is positioned to align with the shifter arm or tab. Install the switch, tighten the retaining nuts or bolts and connect the wiring. Reinstall the console.

After installing the switch, check that the engine starts only in P or N; the starter should not engage with the shifter in any other position. Check also that the back-up lights come on when the selector is placed in R.

Hope this helps (remember comment and rated this).

Aug 02, 2010 | 1988 Honda Prelude

2 Answers

I need the location of a neutral safety switch on a 1999 buick century 3.1L.


I take it that you have an automatic transmission the shift selector /neutral saftey switch switch is located on top of the transmission were the shift cable connects to the trans. Remove the 13 mm nut in the center of the switch and remover the shift cable and lever noting the location of the lever. then remove the bolts holsing the switch to the transmission and the elec connector.

Feb 25, 2010 | 2003 Buick Century

2 Answers

P0705 Trans Range Sensor Circuit Malfunction PRNDL Input


I would check the neutral safety switch. It's located on the shift shaft of the transmission and is known to go bad

Sep 18, 2009 | 2003 Ford Mustang

1 Answer

1996 ford contour transmission range sensor


Transmission range sensor and neutral safety switch are the same thing (when you go to buy the part). It's at the top of your transmission. You'll see the shifting cable connected to it. Here are the instructions for adjustment:
Shift Control Linkage
The transmission shift linkage adjustments must be performed in the order in which they appear.

Column Shift

Place transaxle range selector lever in (D) (OVERDRIVE) position or D (DRIVE) position on vehicles equipped with a transmission control switch (TCS). A weight of 1.4 kg (3 lb) should be hung on the transaxle range selector lever to ensure the lever is located firmly on the (D) (OVERDRIVE) or D (DRIVE) position on vehicles equipped with a transmission control switch (TCS) detent.

Loosen manual control lever-to-control cable retaining nut.

Move transaxle manual control lever to OVERDRIVE position or D (DRIVE) position on vehicles equipped with a transmission control switch (TCS), second detent from most rearward position.

Tighten retaining nut to 17-23 Nm (13-17 lb-ft). Check operation of transaxle in each transmission range position. Make sure that park mechanism and transmission range (TR) sensor are functioning properly.

Floor Shift

Position transaxle range selector lever in DRIVE position against rearward stop. The floor transaxle range selector lever must be held in the rearward position using a constant force of 1.4 kg (3 lb) while linkage is being adjusted.

Loosen manual control lever-to-control cable retaining nut.

Move transaxle manual control lever to DRIVE position, second detent from most rearward position.

Tighten retaining nut to 17-23 Nm (13-17 lb-ft).

Check operation of transaxle in each transmission range position. Make sure that park mechanism and transmission range (TR) sensor are functioning properly.



To take it off, it's a couple of retaining bolts and a wiring harness.

Jun 28, 2009 | 2000 Ford Contour

2 Answers

Car will not come out of park even when break is fully engaged.am unable to shift at all?


check to see if you have brake lights???????? the brake light switch allways go bad on volkswagens.......... this controls the shift lock on the shifter

Oct 09, 2008 | 1999 Volkswagen Passat

Not finding what you are looking for?
2011 Mercedes-Benz Sprinter Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...