Question about Cars & Trucks

Open Question

How to adjust headlights

Headlight adjustment for 2004 toyota alphard

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: can't adjust 2004 Ford Expedition headlight

I had a similar problem on my 04 expedition. I just bought it and the headlights were aiming too far down. A rather larger gap was noticeable between the headlight and the hood. The so called adjustment bolt did nothing. I removed the headlights and found 2 issues. On the adjustment bolt there is a washer. Make sure when you re-install the headlight the washer sets on top of the plastic slot and is visible when looking down behind the headlight. Without the washer being in the correct location it will not tighten the headlight in place.
Second I found the adjustment bolt adjusted nothing. It merely tightened the headlight in place. What I had to do was to loosen this bolt and physically move the headlight into place and the re-tighten the bolt. Hence the slot is the adjustment. Turning the bolt CW or CCW did not move the headlight.
I tried several things trying to figure why the lights would not move until I realized I could move the light with my hands and tightened them in place using the adjustment bolt.

This may not be your issue but I found the owners manual instructions to be useless.

Posted on Jan 02, 2009

  • 14 Answers

SOURCE: headlight adjustment

under the hood, near the rear of the headlamp assemblies, there are adjustment screws with phillips head screwdriver slots. They may be hard to see with the radiator support above the headlamps, but they will be the only phillips adjustment screw heads on the whole headlamp assembly. They will be facing directly vertical facing up

Posted on Apr 13, 2009

LiquidPT
  • 9 Answers

SOURCE: headlight adjustment

If you look at the front of the headlight, there are actually a couple of screws around the edge. These are your adjustment screws.

Posted on Jun 14, 2009

  • 1986 Answers

SOURCE: Headlight adjustment instructions

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams: Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

  • 1986 Answers

SOURCE: Headlight adjustment for 2006 Infiniti M35

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Sep 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do I find the horizontal adjuster for head lights on 2004 Toyota Sienna?


there is no single adjuster but the horizontal adjustment is by using a combination of the 3 adjusting screws
as correct headlight aiming is a requirement by law , have it done by an experienced service center

Nov 26, 2015 | 2004 Toyota Sienna

1 Answer

How to adjust headlights on toyota progres


I assume you mean from low beam to high beam? On the left side "stalk" just push it forward. If you mean adjusting them as to level them, then behind the headlight housing there are screws, csr needs to be level to adjust them.

Feb 09, 2015 | Toyota Cars & Trucks

1 Answer

How to adjust headlight on 2004 nissan murano?


Should b a star shaped screw right near headlight..turns both waysto adjust light

Aug 23, 2014 | 2004 Nissan Murano

2 Answers

How do i adjust my headlights on my gto


Headlight adjustment requires specialized tools.

Jun 08, 2012 | 2004 Pontiac GTO

1 Answer

How do i adjust headlights for a 2004 toyota tacoma


older vehicles have adjustment screws accessible thru trim on front of headlights, newer vehicles have adjustment screws in engine compartment on or near each headlight assembly (usually requiring a torx screwdriver) one screw will adjust side to side and the other will adjust up and down. park vehicle level with lights on & aim at vertical flat surface 20 feet away. Cover headlight you are not adjusting so it doesn't interfere with aiming the one you are working on. Driver's side- just below height of light on vehicle and to the right of straight, Passenger side- just below annd straight ahead. Adjust at low beam. Law enforcement and DMV prefer you have this done by shop.

Oct 03, 2010 | 2004 Toyota Tacoma

1 Answer

White plastic bracket holding headlight


headlight bracket, headlight adjuster, or headlight adjuster bracket

Mar 28, 2010 | 1994 Toyota 4Runner

1 Answer

I Have an Audi a4 Quatro 2004 model. Adjust Low Beams?


There are two adjustment points (screws). For example left headlight: you will see one point near the end of left wing, at bottom side through a wing hole. This is for vertical plane headlight beam adjustment (up-down). Another one point is against water radiator side. This is for horizontal plane headlight beam adjustment (left-right).

Nov 19, 2009 | 2004 Audi A4

1 Answer

Can't adjust 2004 Ford Expedition headlight


I had a similar problem on my 04 expedition. I just bought it and the headlights were aiming too far down. A rather larger gap was noticeable between the headlight and the hood. The so called adjustment bolt did nothing. I removed the headlights and found 2 issues. On the adjustment bolt there is a washer. Make sure when you re-install the headlight the washer sets on top of the plastic slot and is visible when looking down behind the headlight. Without the washer being in the correct location it will not tighten the headlight in place.
Second I found the adjustment bolt adjusted nothing. It merely tightened the headlight in place. What I had to do was to loosen this bolt and physically move the headlight into place and the re-tighten the bolt. Hence the slot is the adjustment. Turning the bolt CW or CCW did not move the headlight.
I tried several things trying to figure why the lights would not move until I realized I could move the light with my hands and tightened them in place using the adjustment bolt.

This may not be your issue but I found the owners manual instructions to be useless.

Dec 28, 2008 | 2004 Ford Expedition

1 Answer

Headlight Adjustment


Good Afternoon. I have a 2004 S60R & had to adjust the headlights recently. The adjustment is easy, but requires a small socket wrench. I forget the exact size of the adjustment bolt, but it's close to 1/4". It's located directly behind each headlight & is fairly easty to reach. Adjust the lights at night on a flat section of road (you'll need a flashlight to see the adjustment bolt when doing this). Hope this helps. David

Aug 25, 2008 | 2004 Volvo S60

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...